• Magazine of the Korean Society of Agricultural Engineers
• /
• v.8 no.1
• /
• pp.1088-1096
• /
• 1966

The following is a method of synthetic unitgraph derivation based on the routing of a time area diagram through channel storage, studied by Clark-Jonstone and Laurenson. Unithy drograph (or unitgraph) is the hydrograph that would result from unit rainfall\ulcorner excess occuring uniformly with respect to both time and area over a catchment in unit time. By thus standarzing rainfall characteristics and ignoring loss, the unitgraph represents only the effects of catchment characteristics on the time distribution of runoff from a catchment The situation abten arises where it is desirable to derive a unitgraph for the design of dams, large bridge, and flood mitigation works such as levees, floodways and other flood control structures, and are also used in flood forecasting, and the necessary hydrologie records are not available. In such cases, if time and funds permit, it may be desirable to install the necessary raingauges, pruviometers, and stream gaging stations, and collect the necessary data over a period of years. On the otherhand, this procedure may be found either uneconomic or impossible on the grounds of time required, and it then becomes necessary to synthesise a unitgraph from a knowledge of the physical charcteristics of the catchment. In the preparing the approach to the solution of the problem we must select a number of catchment characteristic(shape, stream pattern, surface slope, and stream slope, etc.), a number of parameters that will define the magnitude and shape of the unit graph (e.g. peak discharge, time to peak, and base length, etc.), evaluate the catch-ment characteristics and unitgraph parameters selected, for a number of catchments having adequate rainfall and stream data and obtain Correlations between the two classes of data, and assume the relationships derived in just above question apply to other, ungaged, Catchments in the same region and, knowing the physical characteritics of these catchments, substitute for them in the relation\ulcorner ships to determine the corresponding unitgraph parameters. This method described in this note, based on the routing of a time area diagram through channel storage, appears to provide a logical line of research and they allow a readier correlation of unitgraph parameters with catchment characteristics. The main disadvantage of this method appears to be the error in routing all elements of rainfall excess through the same amount of storage. evertheless, it should be noted that the synthetic unitgraph method is more accurate than the rational method since it takes account of the shape and tophography of the catchment, channel storage, and temporal variation of rainfall excess, all of which are neglected in rational method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.9
• /
• pp.6221-6226
• /
• 2015

In this paper, waveguide analysis was interpreted as an optical waveguide using the feedback perturbation method simple and easy to apply compared to the analysis method, while the other almost identical to the numerical calculation method. In addition, efficient coupling with an optical transmission line of optical fiber and the waveguide form the thin film of different functional elements is required in order to achieve the full optical communication system. However, problems arise, such as the light field (field) and the decrease of the access efficiency due to inconsistency in the distribution characteristics of the connection surface by the difference in size of the cross section thereof when connecting the optical fiber and the waveguide directly to the combination of a thin film. Therefore propose a new type of connector structure to increase the efficiency of the connection when connecting the optical fiber waveguide and the thin film was analyzed by applying a coupled mode theory, the binding efficiency of the modified contactor. And by diffusing Ti on the $LiNbO_3$ substrate and a wide range of applications in the manufacture of integrated optical material made of a current low-loss Ti: $LiNbO_3$ optical waveguide and making the Y-branch waveguide, and the properties were confirmed.

• The Plant Pathology Journal
• /
• v.26 no.4
• /
• pp.313-320
• /
• 2010

Genetic instability of the rice blast fungus Magnaporthe oryzae has been suggested as a major factor underlying the rapid breakdown of host resistance in the field. However, little information is available on the mechanism of genetic instability. In this study, we assessed the stability of repetitive DNA elements and several key phenotypic traits important for pathogenesis after serially transferring two isolates though rice plants and an artificial medium. Using isolate 70-15, we obtained a total of 176 single-spore isolates from 10 successive rounds of culturing on artificial medium. Another 20 isolates were obtained from germ tubes formed at the basal and apical cells of 10 three-celled conidia. Additionally, 60 isolates were obtained from isolate KJ201 after serial transfers through rice plants and an artificial medium. No apparent differences in phenotypes, including mycelial growth, conidial morphologies, conidiation, conidial germination, appressorium formation, and virulence, or in DNA fingerprints using MGR586, MAGGY, Pot2, LINE, MG-SINE and PWL2 as probes were observed among isolates from the same parent isolate. Southern hybridization and sequence analysis of two avirulence genes, AVR-Pita1 and AVR-Pikm, showed that both genes were also maintained stably during 10 successive generations on medium and plants. However, one reversible loss of restriction fragments was found in the telomere-linked helicase gene (TLH1) family, suggesting some telomere regions may be more unstable than the rest of the genome. Taken together, our results suggest that phenotype and genotype of M. oryzae isolates do not noticeably change, at least up to 10 successive generations on a cultural medium and in host plants.

• Archives of Plastic Surgery
• /
• v.37 no.4
• /
• pp.481-484
• /
• 2010

Purpose: Congenital dermoid cysts develop during the fusion of the embryo when the ectodermal tissue gets trapped in the line of fusion. Dermoid cysts of the head are rare lesions comprised of epidermal and mesodermal elements. Furthermore, dermoid cysts in the occipital area are extremely rare. Only a few cases of dermoid cysts in the posterior scalp have been reported. Especially, A bilateral, synchronous presentation in this location has not been reported previously in the literature. Methods: All 5 cases had a gradually enlarging mass of the posterior aspect of the scalp. The cysts were mobile, noncompressible, and non-tender, without evidence of an associated sinus tract, skin dimpling, discoloration, or communication with adjacent structures. The CT scan displayed a hypodense cystic lesions about -87 to +24 HU (Housefield units, average +3.2 HU) with hypodense capsule and no postcontrast enhancement. All tumors were found just under the skin, and were well encapsulated, so they were completely removed the mass with adjacent periosteum. Results: On gross findings, all tumors were oval-or round-shaped, and when the cystic tumor was cut open it presented a greasy and caseous substance. Histologically, all specimens contain desquamated squamous epithelium and keratin in the lumen and are encapsulated and lined by keratinized stratified squamous epithelium. And, all cases of posterior mass are the presence of adnexal structures. Conclusion: Appropriate diagnosis requires not only an index of suspicion for this rare tumor a very careful history and search for skin changes. Especially, CT can reveal the exact location of the cyst, its relationship with the adjacent structures. We think that occipital dermoids divide into superficial and deep type. In our cases, because they did not have intra-cranial involvement or fistula formation, they are superficial type. This report describes the clinical and operative aspects of the superficial dermoid cysts and provides a review of the literatures.

• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.409-415
• /
• 2011

The method to improve the detection sensitivity of Hand-held XRF (X-Ray Fluorescence) device currently being developed is discussed. To minimize the loss of the intensity due to atmospheric gas molecules, the vacuum module, which can be filled with atmospheric or He gas, between the sample and the detector was installed. And the change of the detection sensitivity was measured in a vacuum and in the He gas-filled state. As a result, the following three important results were obtained; Firstly, XRF intensity was increased 2~4 times in the low energy range (3~4 keV). It is a very important result because the enhancement of the detection sensitivity means shortening of the detection time in Hand-held XRF device. Secondly, the possibility of detection of the elements less than 3 keV in emission energy was confirmed. Thirdly, the absorption by atmospheric gas molecules can be minimized without vacuum- sealed vessel in Hand-held XRF device, if the vacuum module filled with He gas is used. We concluded that all of three results are very meaningful in the development of a Hand-held XRF device.

• Journal of Life Science
• /
• v.13 no.4
• /
• pp.529-534
• /
• 2003

This study was done to investigated the phytosterol compositions of safflower (Carthamus tinctorius L.) seed. The phytoestrogen activity was also determined using CAT-ELISA Kit in ethanol extract of safflower seed. The phytosterol of safflower seeds was identified using gas chromatography-mass spectrometry after saponification of the oils. The phytosterol content and composition of safflower seed oils were 4% and identified stigmast-5-en-3-ol (3$\beta$, 24S)-form, ${\gamma}$-sitosterol (clionasterol) with Wiley MS spectrum library. The synergistic effect of human estrogen receptor (hER) has been investigated using a minimal chimeric promoters composed of the TATA region of the adenovirus-2 major late promoter (A22MLP) and two consensus perfectly polindromic Xenopus vitellogenin A2 gene estrogen responsive elements (XVEREl19). Transient transfection experiments in tile human breast adenocarcinoma cell line MCF-7, which is known to express the estrogen receptor endogenously, revealed that phytoestrogen from Carthamus tinctorius L. acts as estrogen. We have observed the transcriptional activities stimulated methanol and ethanol extract of safflower seed in MCF-7, were 0.43 and 0.37 respectively, compared to that by $\beta$-estradiol as 1.0. Our data showed that safflower seeds have estrogenic activity methanol and ethanol extracts and ethanol lower than that of $\beta$-estradiol. This result provides the first evidence that the beneficial effect of safflower seeds may be mediated, at least in part, by the stimulating effect of phytoestrogen ell bone-protecting.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.4 no.2
• /
• pp.77-87
• /
• 1986

As for the deformation measurement of structure, there are many controversial points in using the methods by the strain guage, inclinometer, bial guage, and geodetic method because of the difficulty of instrument setting and the problem in the degree of accuracy of the results as well as in the economical aspect. Therefore, to verify the superiority of the Close- Range Photogrammetry method for the structural deformation measurement, the result of load deformation on the model structure, which was made using the Close-Range Photogrammetry method was compard with the results which was made using the methods of dial guage, precision level, and triangulation. In addition to that, to consider the general problem which would happen when C. R. P method was applied to the practical structure. The elements of C. R. P method like camera rotation angle ($\psi$,$\omega$), exposure elevation (Z$_{L}$), and angle of inclined base line ($\theta$) were experimented, and their specificities were reconsidered. As a result, the application of C. R. P method to the general structure is expected to be increased not only in the aspect of accuracy but in the economical aspect.t.

• Journal of KIISE:Software and Applications
• /
• v.27 no.8
• /
• pp.864-876
• /
• 2000

This paper proposes a new scene boundary detection scheme for the MPEG System stream using MPEG Audio information and proves its usefulness by extensive experiments. A scene boundary has a characteristic that the audio as well as video information are changed rapidly. This paper first classifies this scene boundary into three cases ; Radical, Gradual, Micro Changes, with respect to the audio changes. The Radical change has a large-scale changing of decibel value and pitch value at a scene boundary, the Gradual change shows the long-time transition of decibel and pitch values from max to min or vice versa, and the Micro change displays a some change of pitch or frequency distribution without decibel changes. Upon this analysis, a new scene change detection algorithm detecting these three cases is proposed in which a progressive window with a time line is used to trace the changes in the audio information. Some experiments with various movies show that proposed algorithm could produce a high detection ratio for Radical change that is the most popular scene change in the movies, while producing a moderate detection ratio for Gradual and Micro changes. The proposed scene boundary detection scheme could be used to build a database for visual information like MPEG System stream.

• Journal of Distribution Research
• /
• v.7 no.1
• /
• pp.105-127
• /
• 2002

This paper presents an analysis of how the business models of organizations are getting transformed in the Marketspace created by the Internet. We use a research model comprising the transformation scores of four Ps(Product, Price, Promotion, and Place) as dependent variables and three dimensions, Demographics, Technology, and Community elements on the Websites, as explaining variables about the Cyber Transformation of the 4Ps. While most existing literatures have focused on Website's technology, our research model includes 22 five-point-scale items; 10 Demographics /Technology items and 12 Community items. To measure the 4P's transformation scores, the authors selected 14 workable items from the Marketspace Model by Dutta, Kwan, & Segev(1997). A sample of 123 shopping mall Websites comprising three categories(grocery, jewelry/accessory, and cosmetics) from the 100hot.co.kr list are evaluated and the data is analyzed by SPSSWIN 8.0 version. The result shows that there are five significant factors, Technology, Interaction, Connectedness, Business Features, and Domain, while the average transformation scores of 4Ps are at very low level. The factor scores are used in regression analysis for each P. Two factors, Technology and Interaction are influencing all four Ps; Connectedness is influencing only two, Product and Place. Organizations must not simply take their existing business models. They have to adopt the Technology items(navigation, logo, e-mail, guide, graphics) and to facilitate the Interaction items(consulting, number/quality of bulletin boards, participation, offline events) and Connectedness(club activation, contents, partner/site link, entertainment contents) in order to get transformed in the Marketspace successfully in the near future.

• Journal of Welding and Joining
• /
• v.28 no.3
• /
• pp.92-98
• /
• 2010

Ferritic stainless steels, which have relatively small thermal expansion coefficient and excellent corrosion resistance, are increasingly being used in vehicle manufacturing, in order to increase the lifetime of exhaust manifold parts. But, there are limits on use because of the problem related to cosmetic resistance, corrosions of condensation and high temperature salt etc. So, Aluminum-coated stainless steel instead of ferritic stainless steel are utilized in these parts due to the improved properties. In this investigation, Al-8wt% Si alloy coated 409L ferritic stainless steel was used as the base metal during Gas Tungsten Arc(GTA) welding. The effects of coated layer on the microstructure and hardness were investigated. Full penetration was obtained, when the welding current was higher than 90A and the welding speed was lower than 0.52m/min. Grain size was the largest in fusion zone and decreased from near HAZ to base metal. As welding speed increased, grain size of fusion zone decreased, and there was no big change in HAZ. Hardness had a peak value in the fusion zone and decreased from the bond line to the base metal. The highest hardness in the fusion zone resulted from the fine re-precipitation of the coarse TiN and Ti(C, N) existed in the base metal during melting and solidification process and the presence of fine $Al_2O_3$ and $SiO_2$ formed by the migration of the elements, Al and Si, from the melted coating layer into the fusion zone.