• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.169-175
• /
• 2016

The hearth roll, which transfers the cold-rolled strip sheet in a Continuous Annealing Line (CAL), is always subjected to changes in the surface temperature and subsequently experiences thermal stress in service. These variations lead to the generation of thermal cracks on the hearth roll surface as well local plastic deformation. We performed finite element analysis to predict the thermal stress changes on the hearth roll surface and designed the collar shape of the hearth roll to minimize these thermal stresses. Results show that the hearth roll with a collar having an obtuse angle is much more effective than a hearth roll with collar having a right angle when the tangential stress, which is one of main causes leading to surface cracks, is compared for the various conditions. It was found that the tangential stress and the temperature on the surface of hearth roll can be reduced by 51.9% and 26℃ if the shape of roll on collar is re-designed.

• Geomechanics and Engineering
• /
• v.3 no.2
• /
• pp.117-130
• /
• 2011

The methods of design available for geocell-supported embankments are very few. Two of the earlier methods are considered in this paper and a third method is proposed and compared with them. In the first method called slip line method, plastic bearing failure of the soil was assumed and the additional resistance due to geocell layer is calculated using a non-symmetric slip line field in the soft foundation soil. In the second method based on slope stability analysis, general-purpose slope stability program was used to design the geocell mattress of required strength for embankment. In the third method proposed in this paper, geocell reinforcement is designed based on the plane strain finite element analysis of embankments. The geocell layer is modelled as an equivalent composite layer with modified strength and stiffness values. The strength and dimensions of geocell layer is estimated for the required bearing capacity or permissible deformations. These three design methods are compared through a design example. It is observed that the design method based on finite element simulations is most comprehensive because it addresses the issue of permissible deformations and also gives complete stress, deformation and strain behaviour of the embankment under given loading conditions.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.2 s.69
• /
• pp.257-265
• /
• 2004

The aim of this study is to investigate the inelastic buckling behavior of the beams under moment gradient using a line-type finite element method. The method is incorporated the non-uniform yielding of the cross-section caused by the presence of residual stress and accepted model of residual stress so called 'simplified' and 'polynomial' pattern is adopted in this study. The inelastic lateral-torsional buckling results obtained in this study is compared with the buckling results obtained from the design method based on the allowable stress method given in Korean Steel Designers Manual (KSDM 1995). This study have found that the design method in KSDM (1995) is conservative without and with intermediate bracing applied at the mid span of the beam, and there is some scope for improving the provisions of KSDM (1995)

• Genomics & Informatics
• /
• v.4 no.1
• /
• pp.11-15
• /
• 2006

The aim of this study is to identify hRad21-binding sites in human chromosome, the core component of cohesin complex that held sister chromatids together. After chromatin immunoprecipitation with an hRad21 antibody, it was cloned the recovered DNA and sequenced 30 independent clones. Among them, 20 clones (67%) contained repetitive elements including short interspersed transposable elements (SINE or Alu elements), long terminal repeat (LTR) and long interspersed transposable elements (LINE), fourteen of these twenty (70%) repeats clones had Alu elements, which could be categorized as the old and the young Alu Subfamily, eleven of the fourteen (73%) Alu elements belonged to the old Alu Subfamily, and only three Alu elements were categorized as young Alu subfamily. There is no CpG island within these selected clones. Association of hRad21 with Alu was confirmed by chromatin immunoprecipitation-PCR using conserved Alu primers. The primers were designed in the flanking region of Alu, and the specific Alu element was shown in the selected clone. From these experiments, it was demonstrated that hRad21 could bind to SINE, LTRs, and LINE as well as Alu.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.693-702
• /
• 1991

The existence of residual stress in the circumferential butt welded pipes is one of the most important problems concerning stress corrosion cracking in service. In this paper, the residual stress distributions in three kinds of circumferential butt welded pipes were measured by the hole drilling strain gage method and calculation using finite element method is performed and its results are compared with the experiments. At the inner surface of the pipe region near the center line of welding is under high tensile residual stress. However, as the distance from the center line of welding increases, the tensile component decreases and finally becomes compressive residual stress at region far away from the center line of welding. The longitudinal residual stress at the outer surface is compressive regardless of the diameter of pipe and the circumferential stress is changed rom compressive to tensile as pipe diameter increases. The results also demonstrate that the residual stress is mainly caused by self restraint bending force in the pipe welding.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.16 no.3
• /
• pp.315-320
• /
• 2006

There are many types of reduction drives for industrial applications. In general, high precision speed reducer which has a cycloid or involute teeth profile, used to in robot. Because, it is essential to use precision reduction drives for accuracy of position control on robot system. In this paper, we propose a robot speed reducer(RSR) with straight line teeth profile, which has basically a triangle teeth profile. In new straight line teeth profile, we have a good result for strength, stress and stiffness by using finite element analysis and the results indicate that variation of eccentric coefficient affects the optimal tooth motion, and it can lower the stress and noise.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.2
• /
• pp.144-154
• /
• 2000

We propose an algorithm for obtaining a triangular approximation of a trimmed NLRBS surface. Triangular approximation is used in the pre-processing step of many applications such as RP(Rapid Prototyping), NC(Numerical Control) and FEA(Finite Element Analysis), etc. The algorithm minimizes the number of triangular elements within tolerance and generates a valid triangular mesh for STL file and NC tool path generation. In the algorithm, a subdivision method is used. Since a patch is a basic element of triangular mesh creation, boundary curves of a patch are divided into line segments and the division of curves is applied for the interior of the surface. That is, boundary curves are subdivided into line segments and two end points of each line segment are propagated to the interior of the surface. For the case of a trimmed surface, triangulation is carried out using a model space information. The algorithm is superior because the number of elements can be controlled as the curvature of the surface varies and it generates the triangular mesh in a trimmed region efficiently. To verify the efficiency, the algorithm was implemented and tested for several 3D objects bounded by NURBS surfaces.

• Journal of Korean Association for Spatial Structures
• /
• v.10 no.2
• /
• pp.45-60
• /
• 2010

Nonlinear problems for membrane structures are very sensitive in convergence procedure in nonlinear iterations. Therefore many researchers have suggested a lot of ideas in published papers. In this study, authors are trying to get easier solution for taking membrane shape by initial stresses from substitution of the membrane to line elements. To obtain nonlinear stiffness, the nonlinear finite element method is used for both membrane and cable elements, and only geometric nonlinear terms are taken for shape analysis. By some examined models, we can find that the substituted models show better results to get, initial shape in which the concentrating phenomenon is removed at edge parts.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1743-1747
• /
• 2012

The research of superconducting fault current limiter (SFCL) for reduction of the fault current is actively underway in the worldwide. In this paper, we analyzed the characteristics of a SFCL using the transformer and superconducting elements combined mutually in accordance with the fault types. The structure of this SFCL was composed of the secondary and third windings of a transformer connected to the load and the superconducting element, respectively. The provided electric power flew into the load connected to the secondary winding of the transformer in normal state. On the other hand, when the fault occurred in power system, the fault current was limited by closing the line of third winding of the transformer. At this time, the effect of the fault was minimized by opening the fault line in secondary winding of a transformer in power system. The sensing of the fault state was performed by the current transformer(CT) and then turn-on and turn-off switching behavior of the secondary line in the transformer was performed by the silicon-controlled rectifier(SCR). As a result, the proposed SFCL limited the fault current within one-cycle efficiently. Also, the degradation of the superconducting element in the normal state was avoided.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1038-1044
• /
• 2017

We are working on improving the performance by applying the three-dimensional design element to the rotor blades of high pressure supersonic impulse turbine that drives turbo pump of liquid rocket engine. In this paper, based on the shape of a rotor blade of a turbopump turbine designed in the past, a three-dimensional shape is applied to a rotor blade through a stacking line change such as sweep and dihedral. After performing the flow analysis, the changes in the turbine performance characteristics for each design element were carefully examined and the results were summarized.