• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.331-338
• /
• 2005

The rapid advances in high power light sources and arrays as encountered in incandescent lamps have induced dramatic increases in die heat flux and power consumption at all levels of high power LED packaging. The lifetime of such devices and device arrays is determined by their temperature and thermal transients controlled by the powering and cooling, because they are usually operated under rough environmental conditions. The reliability of packaged electronics strongly depends on the die attach quality, because any void or a small delamination may cause instant temperature increase in the die, leading sooner or later to failure in the operation. Die attach materials have a key role in the thermal management of high power LED packages by providing the low thermal resistance between the heat generating LED chips and the heat dissipating heat slug. In this paper, thermal transient characteristics of die attach in high power LED package have been studied based on the thermal transient analysis using the evaluation of the structure function of the heat flow path. With high power LED packages fabricated by die attach materials such as Ag paste, solder paste and Au/Sn eutectic bonding, we have demonstrated characteristics such as cross-section analysis, shear test and visual inspection after shear test of die attach and how to detect die attach failures and to measure thermal resistance values of die attach in high power LED package. From the structure function oi the thermal transient characteristics, we could know the result that die attach quality of Au/Sn eutectic bonding presented the thermal resistance of about 3.5K/W. It was much better than those of Ag paste and solder paste presented the thermal resistance of about 11.5${\~}$14.2K/W and 4.4${\~}$4.6K/W, respectively.

• Korean Journal of Rural Living Science
• /
• v.8 no.2
• /
• pp.111-117
• /
• 1997

In this study we tried to give a decision on propriety of working conditions, to present ideas on reducing work loads. and to grope for efficiency of agricultural works. For this we examined the actual conditions of working environment, farmer's clothes, working posture, working methods, working time, resting state, fatigue recovery methods during cultivating lettuce in the winter greenhouse. And Ive improved harmful factors that affect farmer's health by considering results of previous study and farmer's subjective sensation. And we measured, compared, and analyzed the farmer's work loads before and after improvement. The results of this study are as follows ; 1. According to examine the actual conditions of cultivating lettuce in the winter greenhouse, farmers have experienced physical and mental chronic fatigue on the basis of the hot and humid crops-centered working environment, the rough ground condition, inconsistent arrangement of working stand and sorter, heavy-weared habits. and unsuitable working posture. 2. When we improved harmful factors that affect farmer's health, conformed the positive effects on important work efficiency index such as heart rate, electromyovolume, body temperature, and microclimate inside clothing and work loads were decreased by improving the hot and humid working environment, eliminating the hillock and obstacles of working path. deliver way, arranging the working stand and sorter consistantly, decreasing the clothing weight, improving the working postures and methods as using assistant appliances, alloting the working time and sequence effectively and presenting the light gymnastic exercises and rest for fatigue restoration.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.3
• /
• pp.939-945
• /
• 2014

In most of mobility enhancing plans for the transportation disabled, decisions for the investment priorities are firstly made by the facilities that have lower installation rate or lower satisfaction rate; the decisions are made without analyzing the importance factor (path loading factor) between the facility installation rate and the satisfaction rate together. In this study, a novel method of finding causality between the exogenous latent variables and the endogenous latent variables is provided by using the Structural Equation Model (SEM). The results show that the most influential facilities for the transportation disabled are bus stops, crosswalks and sidewalks in order. Also, a curb height around bus stops, a smoothness of sidewalks and installation of crosswalks traffic light are identified as an important facilities for the Transportation disabled.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.100-106
• /
• 2006

The behavior of spray impinging on the inclined constant temperature flat plate was experimentally investigated. To clarify the wall effect of a high pressure DISI injector, a relative angle of the inclined wall to a spray axis was varied. Spray penetration along the wall was observed optically and it was compared with that of a Fan spray type and Swirl type spray. To evaluate various spray motion quantitatively, a spray path penetration which describe the development of a spray tip along the wall was newly introduced. To observe the structure of an impinging spray, it was visualized by a controlled stroboscope light and its visualized image was captured on an CCD camera. Using the digital image of impinging spray $H_x$ and $R_x$ was extracted to clarify the structure of impinging spray. The main parameter of the relative position of the wall was the inclined angle which was defined as the angle was varied from $0^{\circ}$ (vertical impingement) to $60^{\circ}$ at the same condition.

• Korean Journal of Materials Research
• /
• v.28 no.5
• /
• pp.261-267
• /
• 2018

Hydrothermal synthesis of highly crystalline $TiO_2$ nanorods is a well-developed technique and the nanorods have been widely used as the template for growth of various core-shell nanorod structures. Magneli/CdS core-shell nanorod structures are fabricated for the photoelectrochemical cell (PEC) electrode to achieve enhanced carrier transport along the metallic magneli phase nanorod template. However, the long and thin $TiO_2$ nanorods may form a high resistance path to the electrons transferred from the CdS layer. $TiO_2$ nanorods synthesized are reduced to magneli phases, $TixO_{2x-1}$, by heat treatment in a hydrogen environment. Two types of magneli phase nanorods of $Ti_4O_7$ and $Ti_3O_5$ are synthesized. Structural morphology and X-ray diffraction analyses are carried out. CdS nano-films are deposited on the magneli nanorods for the main light absorption layer to form a photoanode, and the PEC performance is measured under simulated sunlight irradiation and compared with the conventional $TiO_2/CdS$ core-shell nanorod electrode. A higher photocurrent is observed from the stand-alone $Ti_3O_5/CdS$ core-shell nanorod structure in which the nanorods are grown on both sides of the seed layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.458-458
• /
• 2013

We investigated a study on the thermal degradation of boron doped zinc-oxide (BZO) layer which used as a transparent conducting layer on the Cu (In1-xGax) Se2 (CIGS) based thin film solar cells. Devices were annealed under the temperature of $100^{\circ}C$ or 100 hours and then Hall measurement was carried out to characterize the parameters of mobility (${\mu}Hall$), resistivity (${\rho}$), conductivity (${\sigma}$) and sheet resistance (Rsh). The initial values of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh were $29.3cm^2$/$V{\cdot}s$, $2.1{\times}10^{-3}{\Omega}{\cdot}cm$, $476.4{\Omega}^{-1}{\cdot}cm^{-1}$ and $19.1{\Omega}$/${\Box}$ respectively. After the annealing process, the values were $4.5cm^2$/$V{\cdot}s$, $12.8{\times}10^{-3}{\Omega}{\cdot}cm$, $77.9{\Omega}^{-1}{\cdot}cm^{-1}$ and $116.6{\Omega}$/${\Box}$ respectively. We observed that ${\mu}Hall$ and ${\sigma}$ were decreased, and ${\rho}$ and Rsh were increased. In this study, BZO layer plays an important role of conducting path for electrons generated by incident light onthe CIGS absorption layer. Therefore, the degradation of BZO layer characterized by the parameters of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh, affect to the cell efficiency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.2B
• /
• pp.130-142
• /
• 2009

In this paper, we propose a self-adaptation framework that selects a TCP variant adapted to current end-to-end path among available TCP variants. There is no single version of TCP that is suitable to all network environments since the causes for performance degradation are different one another according to characteristics of network environments. Thus, determining that which TCP variants should be selected in order to get best performance is very important. To enable adaptation through such determination, we integrate the existing network estimation schemes and some TCP variants into our framework then make light-weight performance knowledge database for TCP selection. Through implementing and evaluating the proposed framework we show that our solution can help TCP get high and stable performance on the various types of network environments by pure end-to-end.

• Korean Journal of Agricultural Science
• /
• v.38 no.4
• /
• pp.747-752
• /
• 2011

Wireless technology has enabled farmers monitor and control protected production environment more efficiently. Utilization of USN (Ubiquitous Sensor Network) devices also brought benefits due to reduced wiring and central data handling requirements. However, wireless communication loses signal under unfavorable conditions (e.g., blocked signal path, low signal intensity). In this paper, performance of commercial wireless communication devices were evaluated for application to protected crop production. Two different models of wireless communication devices were tested. Sensors used in the study were weather units installed outside and top of a greenhouse (wind velocity and direction, precipitation, temperature and humidity), inside ambient condition units (temperature, humidity, $CO_2$, and light intensity), and irrigation status units (irrigation flow and pressure, and soil water content). Performance of wireless communication was evaluated with and without crop. For a 2.4 GHz device, communication distance was decreased by about 10% when crops were present between the transmitting and receiving antennas installed on the ground, and the best performance was obtained when the antennas were installed 2 m above the crop canopy. When tested in a greenhouse, center of a greenhouse was chosen as the location of receiving antenna. The results would provide information useful for implementation of wireless environment monitoring system for protected crop production using USN devices.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.329-336
• /
• 2006

This paper investigates the problem of protecting multicast sessions in mesh wavelength-division multiplexing (WDM) networks against single link failures, for example, a fiber cut in optical networks. First, we study the two characteristics of multicast sessions in mesh WDM networks with sparse light splitter configuration. Traditionally, a multicast tree does not contain any circles, and the first characteristic is that a multicast tree has better performance if it contains some circles. Note that a multicast tree has several branches. If a path is added between the leave nodes on different branches, the segment between them on the multicast tree is protected. Based the two characteristics, the survivable multicast sessions routing problem is formulated into an Integer Linear Programming (ILP). Then, a heuristic algorithm, named the adaptive shared segment protection (ASSP) algorithm, is proposed for multicast sessions. The ASSP algorithm need not previously identify the segments for a multicast tree. The segments are determined during the algorithm process. Comparisons are made between the ASSP and two other reported schemes, link disjoint trees (LDT) and shared disjoint paths (SDP), in terms of blocking probability and resource cost on CERNET and USNET topologies. Simulations show that the ASSP algorithm has better performance than other existing schemes.

• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.441-448
• /
• 2001

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. However, exhaust gas heat discharged to atmosphere through chimney reaches up to 10~20% of total heat capacity of the oil burred. In order to recover the heat of this exhaust gas and to use for greenhouse heating, the heat pipe type exhaust heat recovery system was manufactured and tested in this experiment. The system consisted of a heat exchanger made of heat pipes, ø15.88${\times}$600mm located in the rectangular box of 675(L)${\times}$425(W)${\times}$370(H)mm, an air suction fan and air ducts. The number of heat pipe was 60, calculated considering the heat exchange amount between exhaust gas and air and heat transfer capacity of a heat pipe. The working fluid of heat pipe was acetone because acetone is known for its excellent heat transfer capacity. The system was attached to the exhaust gas path. According to the performance test it could recover 53,809 to 74,613kJ/h depending on the inlet air temperature of 12 to -12˚at air flow rate of 1.100㎥/h. The temperature of the exhaust gas left the heat exchanger dropped to 100$^{\circ}C$ from 270$^{\circ}C$ after the heat exchange between the suction air and the exhaust gas.