• Korean Journal of Medicinal Crop Science
• /
• v.4 no.1
• /
• pp.74-77
• /
• 1996

This experiment was conducted to evaluated the effect of CM (plant growth regulator) treatment on flowering, pod maturing and root yield components of Astragalus membramaceus Bunge. Three dilution rates (60, 70 and 80 times) were sprayed at $3{\sim}4$ leave stage. As the results, flowering was delayed $25{\sim}35$ days than August 13 of control and higher dilution rates was more effective to delay flowering. At the havesting time, be compared with non-treatment, plant height reduced $7.6{\sim}18.9\;cm$ and number of matured pods were decreased $50.6{\sim}76.1$ by increasing dilution rates. However, weight of dry root per plant was increased to 29% and dry root yield per 10a was increased to 28% in dilution rates 70 compared with non-treatment.

• Journal of Korean Society of Transportation
• /
• v.26 no.4
• /
• pp.99-110
• /
• 2008

It is commonly estimated that there is a much higher potential for accidents at a crossroads than along a single road due to its plethora of conflicting points. According to the 2006 figures by the National Police Agency, the number of traffic accidents at crossroads is greatly increasing compared to that along single roads. Among others, crossroads installed with traffic signals have more varied influential factors for traffic accidents and leave much more room for improvement than ones without traffic signals; thus, it is expected that a noticeable effect could be achieved in safety if proper counter-measures against the hazards at a crossroads were taken together with an estimate of causes for accidents This research managed to develop models for accident forecasts and accident intensity by applying data on accident history and site inspection of crossroads, targeting four selected downtown crossroads installed with traffic signals. The research was done by roughly dividing the process into four stages: first, analyze the accident model examined before; second, select variables affecting traffic accidents; third, develop a model for traffic accident forecasting by using a statistics-based methodology; and fourth, carry out the verification process of the models.

• Journal of Fashion Business
• /
• v.20 no.4
• /
• pp.189-206
• /
• 2016

A breast model was for the human body was devised by studying a body scan and human body index of a desirable breast type. Thus, when manufacturing various 3D models, these results can accordingly become a fundamental basis for realizing a desirable breast model. This study aims to provide a basic data for designing the cup patterns of brassieres in order to improve the function and wearing comfort. The comfort of three kinds of brassieres were compared: one manufactured by the actual measured size; another manufactured as per the ratio of desirable upper and lower breast lengths; and the third manufactured by the 3D model attained by the desirable human body ratio. In this study, we suggest a process for realizing the desirable breast model using the ratio of bust breadth and waist front length, which are the components for deciding the appropriate position and size of breast, and which are easy to measure. The ideal breast shape is an equilateral triangle formed by connecting the nipple with the center of the clavicle. After deciding the interval between the nipples, this value can be used to configure the locations of nipples by drawing a tangent, with equal length, from the anterior neck point (which is the center of clavicle) to the nipple. Also, since inside points of breast do not exist, the outer point of breast, upper point of breast, and below point of breast on the same plane, and the depths from the nipple point to the respective points, are applied to simulate a 3D image, by modifications along the x, y, and z axes. Depending on the type of breast, the length from the center of shoulder to the nipple, the diameter of breast, upper length of breast, and the position of nipple, are different. In conical or protruding breast, the wearing sensation is better when the nipple point of brassiere was lifted, by modifying the upper and lower lengths of breast. Considering the wearing sensation and function of a brassiere, it was better to leave the wearer's size as it is and use a pad within the same cup, rather than increase the basal area of the breast in order to increase the volume.

• The Journal of the Korea Contents Association
• /
• v.17 no.5
• /
• pp.337-356
• /
• 2017

The purpose of the research is to explore the main cause and effect of successful marriage that Korean husbands, who are multicultural families had. To do the research, the experiment has been done with 7 husbands for 2 months. The 7 husbands took depths interview and analyzed the result by grounded theory approach. As a result, the husband experienced 'repentance of marriage' because of 'unready marriage', but 'Raising children', 'Helping housework' and 'recognition from friends and colleague' have affected the husbands to have a successful marriage adaptation. Based on the result, a political and practical proposal has been proposed to the Korean husbands who are multi-cultural family. Here are the examples of the proposal. As a social welfare policy, 'obligation of information offering for prospective spouse', 'following the Labor Standards and parental leave', 'expansion of visiting supervise system' and 'making guidance for husbands and distribute map of Immigration Office, Multicultural Family Support Center and Community Center' have proposed. And as an alternative plan for a practical social welfare policy and continuous social awareness improvement, 'various education program', 'a program with domestic married couple', 'a program with parents-in-law', 'a specific program to increase the housework participation for husbands' and necessity of development and practice of group program for husband have been emphasized.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.596-608
• /
• 2017

In 2002, the government arranged an institutional strategy to make it possible for a consumers to make a claim for damages caused by product defects against a business that produces and sells a product by enforcing the Product Liability Law(hereinafter referred to as 'PL'). On the other hand, due to the recent humidifier sterilizer accident, approximately 12 cases of related bills, such as a revised bill for the product liability law, have been proposed to the National Assembly at present in an effort to introduce the group action system and punitive compensation system for the purpose of the strengthening of the corporate product liability, and consumer damage relief. Ironically, as much as 62.6% of small & medium businesses, which are actual interested parties to this bill, are unaware of this. Many companies are responding to PL with the rationalization of document preparation & storage, clarification of responsibility relations with related business operators, and PL insurance policy purchase, or securing compensation funds as a means of Product Liability Defense(PLD), but the methods of preparation such as this leave much room for limits on the considerations of product design and product safety. This paper presents the individual management system model with more focus on product safety by looking into the clear concept of PL and the countermeasures against it, grasping the relevance between the PL system and individual management system, and integrating the PL response system in preparation for the PL. It is hoped that the result of this research objective will be evaluated as a rational countermeasure for small & medium businesses to respond effectively to the PL.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.68-93
• /
• 1998

The physical properties of polymer are greatly influenced by the extent to which a resin cures. The presence of un reacted monomer can, have a plasticizing effect on the polymer, thereby altering the physical and mechanical properties of dentin bonding agent (DBA). If the DBA does not polymerize sufficiently, it will leave a weak bonding layer and lead to lower bond strength. The purpose of this study was to evaluate the shear bond strengths(SBS) and the degree of conversion (DC) of 4 commercialy avilable dentin bonding systems which are composed of 2 multi-bottle systems [Scotchbond Multi-Purpose (SMP), AeliteBond(AB)] and 2 onebottle systems [SingleBond(SB), One-Step(OS)]. For shear bond strength measurement, labial surfaces of freshly extracted bovine incisors were ground with # 600 grit SiC paper to expose dentin. Four different groups of samples were formed, with 10 samples. being made for each of the 4 commercial DBA in each group according to the curing sequences of DBA and overlayer thickness of composites: Group I (standard cure and 1mm thick composites) : The DBA was light cured and the composites of 1mm thickness was applied ; Group II (standard cure and 2mm thick composites) : The DBA was light cured and the composites of 2mm thickness was applied; Group III (simultaneous cure and 1mm thick composites) : The DBA was not light-cured and simultaneously cured with composites of 1mm thickness; Group N (simultaneous cure and 2mm thick composites) : The DBA was. not light-cured and simultaneously cured with composites of 2mm thickness. The SBS was measured immediately after the composites was bonded to the bovine dentin using an Instron machine. The DC of the DBA was examined in a thin film under simulated conditions of the experimental groups according to the curing sequences and overlayer thickness of composites in the SBS test. using a Fourier transform Infrared(FTIR) spectrometer. The following results were obtained from SBS tests and DC measurements 1. In SBS tests, the multi-bottle DBA(SMP, AB) had a generally higher bond strength values than the one bottle DBA(SB, OS). In DC measurements, the one bottle DBA(SB, OS) had a significantly higher DC than the multi-bottle DBA(SMP, AB). 2. In all DBAs except OS, there was no significant difference between the bond strength of group I (standard cure and 1mm thick composites) and that of group III (simultaneous cure and 1mm thick composites). SMP, SB in Group I had a significantly higher DC than those in group III, but AB, OS in group I had a significantly lower DC than those in group III 3. All DBAs in Goup II (standard cure and 2mm thick composites) had significantly higher bond strength and DC than those in Group N (simultaneous cure and 2mm thick composites). 4. In all DBAs, there was no significantly different SBS and DC between Group I and Group II, but all DBAs in Group III had significantly higher SBS and DC than those in Group IV.

• Journal of Intelligence and Information Systems
• /
• v.13 no.2
• /
• pp.43-53
• /
• 2007

e-Learning education system as the next educational trend supporting remote and multimedia education. However, the students stay mainly at remote place and it is hard to certificate whether he is really studying now or not. To solve this problem, some solutions were proposed such as instructor's supervision by real time motion picture or message exchanging. Unhappily, as you can see, it needs much cost to establish the motion exchanging system and trampling upon human rights could occasion to reduce the student's will. Accordingly, we propose the new intelligent system based on face recognition to reduce the system cost. The e-Learning system running on the web page can check the student's status by motion image, and the images transfer to the instructor. For this study, 20 students and one instructor takes part in capturing and recognizing the face images. And the result produces the prevention the leave of students from lecture and improvement of attention.

• Journal of Technologic Dentistry
• /
• v.8 no.1
• /
• pp.5-16
• /
• 1986

In order to provide the better and more effective dental health service, the study for manpower of dental laboratory technician with some relevant factors such as institutions for education and training, employment status and distribution of technicians, etc. was carried out through survey for 3,885 licensed technicians during 1965 - 1985. Results were obtained through the study as follows: 1. There are 14 junior health colleges in Korea and 3,106(79.9%) licensed dental technicians out of 3,885 graduated from health colleges and rest of them obtained their licenses through practical training in dental clinics. 2. 8,030 applicants have applied to the national examination which was carried out for 22 times during 1965 - 1985. The passing rate in the examination for 22 times showed 48.3% in average. 3. The dental technicians are working mostly in 404 dental laboratories and 2,522 dental clinics and hospitals through out the country. However, most technicians are dominantly working in large citis, because 255 (63.1%) dental laboratories and 1,537 (60.9%) dental clinics and hospitals are mainly located in Seoul and Busan. 4. Regarding distribution of the dental technician, 1,126(52.1%) technicians have been employed in the dental institutions, however, 530 (24.5%) could not have a job and the rest of them (504 technicians: 23.3%) were in leave absence from military service, travelling abroad and unknown reasons. 5. Through reference review, it was found that there were 95,886 dental technician (9/ 100,000 population) in the world during 1973$\sim$1977. However, 91,553 dental technicians lived in the developed countries (14/100,000 population)) also ratio between the dentist and the dental technician in the world showde 1:0.38. In such coentries where per capita income showed $100 in average, the distribution of the dental technician showed 0.272 per 100,000 population. 6. In an estimation of demand and supply for the dental technicians by the year from 1985 through 1996 in Korea, the supply is estimated by the capacity of educational institutions as over-production even through such estimation based on the future incresing of GNP and ratio between the dentist and the dental technicianas and also ratio between the dental technician and general population. At present such ratio shows less compared with the developed contries, however, it is estimated as over-supply in 1994.

• Journal of Korean Society of Transportation
• /
• v.23 no.2
• /
• pp.75-82
• /
• 2005

To relieve congestion in the current system of intercity transportation, the Korea decided in 1990 to construct a high-speed railroad between Seoul and Busan and it is now in operation. This new mode of transportation significantly cut travel time between major cities and a trip from Seoul to the southeastern port of Busan. Since the KTX opening, average daily passenger numbers on both the Gyeongbu and Honam lines have increased about 1.3 fold over 2003 levels. As of December 2004, the KTX trains are carrying about 81,000 people a day. On KTX routes, the daily number of airline passengers dropped. Express long-distance bus traffic also dropped by 20% to 30%, while that on short-distance routes (100km or less) increased by about 20%. These figures clearly indicate that the Korean transportation network is becoming railroad-centric. However, the number of KTX passengers is fewer than anticipated possibly due to the Korean economic downturn and the operation of the KTX will leave many existing Saemaul and Mugunghwa train sets idle, which will be put into operation for areas, not covered by the KTX. When all the existing major lines have been electrified, more high-speed rail services will be phased in using direct connections to maximize operational efficiency. And also, the dual management by KTX and conventional rail will be regarded as the promotion of the benefit of the public.

• Korean Journal of Family Social Work
• /
• no.43
• /
• pp.37-59
• /
• 2014

The purpose of this study is to analyze and find the relative importance of the factors impacting on the intent to leave among the female care worker's the labor properties, Total 540 questionnaire were distributed and collected from 387 female care workers working at the area of Daegu and GyeongBuk. The logistic regression analysis was used to analyze the relative importance among the factors. The results of the study are the followings: Academic ability, lower subjective-evaluation of remuneration, non-business contracts, labor intensity, the relationship between the user, the relationship between the agency providing are factors influencing on the turnover intention. In other words, higher education, lower subjective-evaluation of remuneration, more work than the contract, higher labor intensity, the female care workers have higher probability of turnover intention. Based on the results of the study, this paper suggests some implications as policy and practice.