• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.42-44
• /
• 1994

This paper presents the method of estimating integral coefficients of new distance relaying algorithm for transmission line protection. The proposed method is based on the differential equation calculates impedance value by approximation of integral term of integro-differential equation which relate voltage with current. As a result, we can determine the integral coefficients in least square error sense in frequency domain and we take into consideration the analog filter characteristics and frequency domain characteristics of the system to be protected. The simulation results showed that these coefficients can be successfully used to obtain impedance value in distance relay.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.481-490
• /
• 2003

This paper presents an efficient eigensolution method for non-proportionally damped systems. The proposed method is obtained by applying the accelerated Newton-Raphson technique and the orthonormal condition of the eigenvectors to the linearized form of the quadratic eigenproblem. A step length and a selective scheme are introduced to increase the convergence of the solution. The step length can be evaluated by minimizing the norm of the residual vector using the least square method. While the singularity may occur during factorizing process in other iteration methods such as the inverse iteration method and the subspace iteration method if the shift value is close to an exact eigenvalue, the proposed method guarantees the nonsingularity by introducing the orthonormal condition of the eigenvectors, which can be proved analytically. A numerical example is presented to demonstrate the effectiveness of the proposed method.

• Proceedings of the PSK Conference
• /
• 2002.10a
• /
• pp.399.3-399.3
• /
• 2002

Near-infrared (NIR) system was used to determine rapidly and simply indomethacin in buffer solution for a dissolution test for tablets and capsules. Indomethacin standards were prepared ranging from 10 to 50ppm using mixture of phosphate buffer(pH 7,2) and water(1:4), The near infrared(NIR) transmittance spectra of indomethacin standard solutions were collected by using a quartz cell in 1 mm and 2mm pathlength, Partial least-square regression (PLSR) was explored to develop calibration models over the spectral range 1100-1700nm. (omitted)

• Journal of Korean Port Research
• /
• v.10 no.1
• /
• pp.53-61
• /
• 1996

This paper describes the effect of wave control using submerged flat plate by the numerical calculation and the hydraulic model test. The boundary element method is used to develop a numerical solution for the flow field caused by monochromatic oblique waves incident upon an infinitely long, sumerged flat plate situated in arbitrary water depth. The effect of wave blocking is examined according to the change of length, submerged depth of flat plate and incident angles. Numerical results show that longer length, shallower submergence of flat plate and larger incident angles enhance the effect of wave blocking. To validate numerical analysis method, hydraulic model test was conducted in 2-D wave flume with 60 cm metal sheet. Reflected waves are extracted from water surface elevation in front of the location of a submerged plate by least square method with 3 wave gages. From comparing experimental results with numerical results, efficiency of numerical analysis method by this study could be confirmed well within wide ranges of wave frequencies.

• Information Systems Review
• /
• v.25 no.2
• /
• pp.163-180
• /
• 2023

Based on the Technology-Organization-Environment (TOE) model, this study proposed a research model that explains the continuance intention of users in the with Covid-19 era considering the technical, organizational, and environmental aspects of Remote Work Solution (RWS). To verify the research model and hypothesis, an online survey was conducted on domestic RWS users. Partial least squares (PLS) were utilized to analyze the collected 411 data. As a result of the analysis, it was found that functionality and security level had positive impacts on both productivity improvement and satisfaction. However, it was also confirmed that organizational readiness had a positive effect on productivity improvement but did not affect satisfaction. Furthermore, the results revealed that government support had a positive relationship with continuance intention, but the health concerns did not. Finally, the correlations between productivity improvement, satisfaction, and continuous intention were confirmed to be significant. Therefore, 9 out of a total of 11 hypotheses were supported.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.8
• /
• pp.945-956
• /
• 1999

This work reports a set of approximate analytical solutions describing the initial transient process of close-contact melting between a rectangular parallelepiped solid and a flat plate on which either constant temperature or constant heat flux is imposed. Not only relative motion of the solid block tangential to the heating plate, but also the density difference between the solid and liquid phase is incorporated in the model. The thin film approximation reduces the force balance between the solid weight and liquid pressure, and the energy balance at the melting front into a simultaneous ordinary differential equation system. The normalized model equations admit compactly expressed analytical solutions which include the already approved two-dimensional solutions as a subset. In particular, the normalized liquid film thickness is independent of all pertinent parameters, thereby facilitating to define the transition period of close-contact melting. A unique behavior of the solid descending velocity due to the density difference is also resolved by the present solution. A new geometric function which alone represents the three-dimensional effect is introduced, and its properties are clarified. One of the representative results is that heat transfer is at least enhanced at the expense of the increase in friction as the cross-sectional shape deviates from the square under the same contact area.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.313-316
• /
• 2008

Although the positioning accuracy of the Global Positioning System (GPS) has been studied extensively and used widely, it is still limited due to errors from sources such as the ionospheric effect, orbital uncertainty, antenna phase center variation, signal multipath and tropospheric influence. This investigation addresses the tropospheric effect on GPS height determination. Data obtained from GPS receivers and co-located surface meteorological instruments in 2003 are adopted in this study. The Ministry of the Interior (MOl), Taiwan, established these GPS receivers as continuous operating reference stations. Two different approaches, parameter estimation and external correction, are utilized to correct the zenith tropospheric delay (ZTD) by applying the surface meteorological measurements (SMM) data. Yet, incorrect pressure measurement leads to very poor accuracy. The GPS height can be affected by a few meters, and the root-mean-square (rms) of the daily solution ranges from a few millimeters to centimeters, no matter what the approach adopted. The effect is least obvious when using SMM data for the parameter estimation approach, but the constant corrections of the GPS height occur more often at higher altitudes. As for the external correction approach, the Saastamoinen model with SMM data makes the repeatability of the GPS height maintained at few centimeters, while the rms of the daily solution displays an improvement of about 2-3 mm.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.130-140
• /
• 1998

This paper presents a method to estimate subpixel accuracy motion vectors using a mathermatical model withoug interpolation. the proposed method decides the coefficients of mathematical model, which represents the motion vector which is achieved by full search. And then the proposed method estimates subpixel accuracy motion vector from achieved mathematical model. Step by step mathematical models such as type 1, type 2, type 3, modified bype 2, modified type 3, and Partial Interpolation type 3 are presented. In type 1, quadratic polynomial, which has 9 unknown coefficients and models the 3by 3 pixel plane, is used to get the subpixel accuracy motion vectors by inverse matrix solution. In type 2 and 3, each quadratic polynomial which is simplified from type 1 has 5 and 6 unknown coefficients and is used by least square solution. Modified type 2 and modified type 3 are enhanced models by weighting only 5 pixels out of 9. P.I. type 3 is more accurate method by partial interpolation around subpixel which isachieved by type 3. LThese simulation results show that the more delicate model has the better performance and modified models which are simplified have excellent performance with reduced computational complexity.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.127-133
• /
• 1999

This paper is a research about system identification which optimizes uncertain geothechnical properties from the data measured during geotechnical design and construction. Various numerical optimization algorithms of Simplex method, Powell method, Rosenbrock method and Levenberg-Marquardt method were applied to the excavation problem to determine which method showed the best results with respect to robustness of success in finding an optimal solution to within a certain accuracy and number of function evaluations. From the results of numerical analysis, all of four algorithms are converged to exact solution after satisfying the allowed criteria, and Levenberg-Marquardt's algorithms was identified to be the most efficient method in number of function evaluations. System identification was applied to geotechnical engineering problems, possibly being occurred in field, to verify its applicability : estimation of settlement due to self-weight consolidation in dredged and filled soil. For self-weight consolidational settlement of a dredged soil, a program of evaluating the constitutive relationship of effective stress-void ratio-permeability was developed by using the technique of system identification. Thus, consolidational characteristics of a dredged soil, having a very high initial void ratio, can be evaluated.

• Korean Journal of Geomatics
• /
• v.2 no.2
• /
• pp.139-143
• /
• 2002

The rational polynomial coefficients (RPC) model is a generalized sensor model that is used as an alternative solution for the physical sensor model for IKONOS of the Space Imaging. As the number of sensors increases along with greater complexity, and the standard sensor model is needed, the applicability of the RPC model is increasing. The RPC model has the advantages in being able to substitute for all sensor models, such as the projective, the linear pushbroom and the SAR. This report aimed to generate a RPC model from the physical sensor model of the KOMPSAT-1(Korean Multi-Purpose Satellite) and aerial photography. The KOMPSAT-1 collects 510~730 nm panchromatic imagery with a ground sample distance (GSD) of 6.6 m and a swath width of 17 km by pushbroom scanning. The least square solution was used to estimate the RPC. In addition, data normalization and regularization were applied to improve the accuracy and minimize noise. This study found that the RPC model is suitable for both KOMPSAT-1 and aerial photography.