• Journal of the Korean Chemical Society
• /
• v.61 no.5
• /
• pp.238-243
• /
• 2017

In this study, water treatment sludge carbonized with $400^{\circ}C$ was tested as an adsorbent for the removal of Pb and Cd in water. The carbonized sludge was characterized by thermo-gravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray fluorescence spectrometry (XRF), and surface area analysis. Carbonized sludge exhibited much higher specific surface area and total pore volume than water treatment sludge itself. In batch-type adsorption process, carbonized sludge represented better adsorption performance for Pb than Cd, achieving 90~98% at the concentrations conducted in the experiments. Equilibrium data of adsorption were analyzed using the Freundlich and Langmuir isotherm models. It was seen that both Freundlich and Langmuir isotherms have correlation coefficient $R^2$ value larger than 0.95. The results of studies indicated that carbonized water treatment sludge by heat treatment could be used as an efficient adsorbent for the removal of Pb and Cd from water.

• Clean Technology
• /
• v.7 no.2
• /
• pp.141-149
• /
• 2001

The effects of various factors such as adsorption temperature, interstitial velocity, species and concentration of adsorbates(benzene and toluene) and aspect ratio(L/D) on adsorption characteristics were investigated in a fixed bed with activated carbon. The breakthrough time in a fixed bed was decreased with the increasing of adsorption temperature, interstitial velocity and concentration of adsorbates. The interstitial velocity, concentration of adsorbates and adsorption temperature had influenced considerably upon the MTZ(mass transfer zone) and LUB(length of unused bed) obtained through the breakthrough curves, while aspect ratio(L/D) had smaller effect than former factors. Especially, the concentration of adsorbates among factors have the largest effect on MTZ and LUB. From comparison with the model isotherms, such as the Langmuir, Freundlich and Langmuir-Freundlich, the experimental isotherm data of benzene and toluene agreed farily well to three adsorption isotherm models.

• Journal of Environmental Science International
• /
• v.27 no.6
• /
• pp.401-410
• /
• 2018

Waste citrus peel-based activated carbon (WCAC) was prepared from waste citrus peels by activation with KOH. The removal of Cu and Pb ions from aqueous solution by the prepared WCAC was investigated in batch experiments. The solution pH significantly influenced Cu and Pb adsorption capacity and the optimum pH was 4 to 6. The adsorption of Cu and Pb ions by WCAC followed pseudo-second-order kinetics and the Langmuir isotherm model. The maximum adsorption capacity calculated by Langmuir isotherm model was 31.91 mg/g for Cu and 92.22 mg/g for Pb. As the temperature was increased from 303 K to 323 K, the ${\Delta}G^{\circ}$ value decreased from -7.01 to -8.57 kJ/mol for Cu ions and from -0.87 to -2.06 kJ/mol for Pb ions. These results indicated that the adsorption of Cu and Pb by WCAC is a spontaneous process.

• Korean Journal of Environmental Agriculture
• /
• v.35 no.1
• /
• pp.24-31
• /
• 2016

BACKGROUND: Heavy metal adsorption not only depends on rapid cooling slag(RCS) characteristics but also on the nature of the metals involved and on their competitive behavior for RCS adsorption sites. The goal of this study was to investigate the competitive absorption characteristics of Cu, Cd and Zn in single- and multi-metal forms by RCS.METHODS AND RESULTS: Both single- and multi-metal adsorption experiments were conducted to determine the adsorption characteristics of RCS for the heavy metals. Adsorption behaviors of the heavy metals by RCS were evaluated using both the Freundlich and Langmuir adsorption isotherm equations. The maximum adsorption capacities of metals by RCS were in the order of Cu(16.6 mg/g) > Cd(8.1 mg/g) > Zn(6.2 mg/g) in the single-metal adsorption isotherm and Cu(14.5 mg/g) >> Zn(1.3 mg/g) > Cd(0.6 mg/g) in the multi-metal adsorption isotherm. Based on data obtained from Freundlich and Langmuir adsorption models and three-dimensional simulation, multi-metal adsorption behaviors differed from single- metal adsorption due to competition. Cadmium and Zn were easily exchanged and substituted by Cu during multi-metal adsorption.CONCLUSION: Results from adsorption experiments indicate that competitive adsorption among metals increases the mobility of these metals.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.9
• /
• pp.37-45
• /
• 2010

Sorption characteristics of arsenic on furnace slag were investigated to remove arsenic from groundwater using furnace slag, which is industrial waste generated from steel company. Adsorption isotherm experiments and kinetic sorption experiments were performed and the chemical characteristics of supernatants from these experiments were analyzed. Results showed that all supernatants were alkaline (above pH 9) and the highest ion concentration in the solution was found with calcium (30~50 mg/L). Results of adsorption isotherms were more adequately described by the Freundlich model than Langmuir model. From adsorption isotherms experiments, it was noted that the adsorption amount of As(V) was 87% higher than that of As(III). Results of kinetic sorption experiments were more properly fitted by pseudo second order (PSO) model than pseudo first order model. Equilibrium adsorption amount ($q_e$) and relaxation time ($t_r$) calculated from PSO model increased with initial concentration of arsenic. Equilibrium adsorption amount of As(V) was higher than that of As(III) and relaxation time of As(V) was shorter than that of As(III). Adsorption isotherm results could be predicted by kinetic adsorption results, since equilibrium adsorption amount calculated through PSO model generally agreed with equilibrium adsorption amount measured from adsorption isotherm.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.619-626
• /
• 2009

The objective of this study was to evaluate the efficiency of Fe and Mn oxides coated granular activated carbons (FMOCGs) for the removal of arsenite and arsenate by oxidation and adsorption mechanisms using surface characterization and batch adsorption experiments. Within four manufactured adsorbents, Fe and Mn contents of FMOCG-1 was the highest (178.12 mg Fe/g and 11.25 mg Mn/g). In kinetic results, As(III) was removed by oxidation and adsorption with FMOCGs. Removal of arsenic by FMOCGs increased as pH value of the solution decreased. The adsorption isotherm results were well fitted with Langmuir isotherm. Adsorption amount of As(V) onto FMOCGs was higher than that of As(III) and the maximum adsorption capacities of FMOCGs for As(III) and As(V) were 1.38~8.44 mg/g and 2.91~9.63 mg/g, respectively.

• Journal of Environmental Science International
• /
• v.31 no.8
• /
• pp.691-706
• /
• 2022

Magnetic activated carbon was prepared by adding a magnetic material to activated carbon that had been prepared from waste citrus peel in Jeju. The adsorption characteristics of an aqueous solution of the antibiotic trimethoprim (TMP) were investigated using the magnetic activated carbon, as an adsorbent, and response surface methodology (RSM). Batch experiments were carried out according to a four-factor Box-Behnken experimental design affecting TMP adsorption with their input parameters (TMP concentration: 50~150 mg/L; pH: 4~10; temperature: 293~323 K; adsorbent dose: 0.05~0.15 g). The significance of the independent variables and their interaction was assessed by ANOVA and t-test statistical techniques. Statistical results showed that TMP concentration was the most effective parameter, compared with others. The adsorption process can be well described by the pseudo-second-order kinetic model. The experimental isotherm data followed the Langmuir isotherm model. The maximum adsorption capacities of TMP, estimated with the Langmuir isotherm model were 115.9-130.5 mg/g at 293-323 K. Also, both the thermodynamic parameters, ΔH and ΔG, have both positive values, indicating that the adsorption of TMP by the magnetic activated carbon is an endothermic reaction and proceeds via an involuntary process.

• Journal of Environmental Science International
• /
• v.2 no.4
• /
• pp.357-365
• /
• 1993

This study was conducted for the efficient utilization of biomaterials such as starch residue, tangerine skin, and green tea residue, which are agricultral by-products discarded in Cheju Province annually, as adsorbents and biomaterials were examined for their removal ability of heavy metal ions in waste water by batch adsorption experiments. The removal efficiency of biomaterials for heavy metal ions was above 80-90% and almost similar to activated carbon and the adsorption ability of those treated with 포르말린 was improved in the green tea residue only for $Pb^{2+}$, $Cu^{2+}$, and $Zn^{2+}$. In the conditions of pH, the removal efficiency of heavy metal ions was high in the range of 5-7. In the solutions which heavy metal ions were mixed, the removal efficiency was similar at $Ag^+$, $Pb^{+2}$ and reduced to about 10% at the other ions, as compared with the solutions they were not mixed. Adsorption isotherm of biomaterials was generally obeyed to Freundlich formular than Langmuir formular and Freundlich constant, 1/n were obtained in the range of 0.1-0.5.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.4
• /
• pp.1-8
• /
• 1999

This study was aimed ultimately to develop an adsorption process treating heavy metal wastewater by utilizing activated carbon using flyash. The affecting factors in adsorption process on heavy metal by flyash adhesion-activated carbon are s follows. Factors such as pH, and quality of activated carbon, and reaction time made batch adsorption isotherm described adsorption capacity was made use of the investigation to evaluate adsorptive possibility of heavy metal.As the results of this study, H ion has influence on adsorption of heavy metal if pH is low. As reaction time is transformed, factors such as optimum reaction time is taken into consideration an adsorptive process of heavy metal because an adsorption and a reduction process occur. Adsorption isotherm of adhesion-activated carbon was generally obeyed to Freundlich formular than Langmuir formular and Freundlich constant, l/n were obtained in the range of 0.1~0.5.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.1
• /
• pp.22-28
• /
• 2017

BACKGROUND: There is very limited knowledge of the effects of biochar derived from exhausted coffee residue on metal adsorption processes. Furthermore, only limited information is available on the adsorption mechanism of copper. The aim of this study was to evaluate the absorption behaviors of copper by biochar derived from exhausted coffee residue. METHODS AND RESULTS: Biochars produced by pyrolysis of exhausted coffee residue at $300^{\circ}C$(CB300) and $600^{\circ}C$(CB600) were characterized and investigated as adsorbents for the removal of copper from aqueous solution. The results indicated that the adsorption equilibrium was achieved around 2 h and the pseudo-second-order kinetic model fit the data better than the pseudo-first-order kinetic model. The maximum Cu adsorption capacities of CB600 by Freundlich and Langmuir isotherms were higher than those of CB300. The adsorption data were well described by a Langmuir isotherm compare to Freundlich isotherm. CONCLUSION: Our results suggest that exhausted coffee residue can be used as feedstock materials to produce high quality biochar, which could be used as adsorbents to removal copper.