• Korean Chemical Engineering Research
• /
• 제58권2호
• /
• pp.286-292
• /
• 2020

본 연구에서는 별도의 이미지 분석 장비를 사용하지 않고 정량적으로 알부민의 농도를 측정할 수 있는 회전각도를 이용한 3차원 종이 칩(3D-PADs)를 제시한다. 변색된 구간의 회전각도를 측정하는 간단한 방법으로 검출을 시연하였다. 3D-PADs는 왁스 프린터를 이용한 인쇄와 라미네이팅 과정을 거쳐 빠르게 제작할 수 있다. 3D-PADs는 샘플의 알부민을 검출하기 위하여 citrate buffer와 tetrabromophenol blue를 흡수시켰다. 3D-PAD의 흡수패드에 샘플 용액을 흡수시키면, 샘플 용액은 형성된 유로를 통하여 수직 및 수평 흐름을 통해 분석 구간으로 흐른다. 변색된 구간의 회전각도는 특정한 알부민의 농도를 나타내며, 알부민 측정의 신뢰할 수 있는 값임을 확인할 수 있었다.

• Current Photovoltaic Research
• /
• 제4권4호
• /
• pp.159-163
• /
• 2016

Piled snow upon PV module interferes with Photoelectric Effect process through photovoltaic directly. As a result of this phenomenon, its generation efficiencies keep decreasing or are stuck at zero power generating status. In addition, PV facilities have been installed on those places such as water surface, roof-top, and other isolated places, dealing with conditions of "Securing high REC weighted value", "Difficulty of securing land" and so forth. Through this study, we are able to actualize the function of heating over PV modules when it snows. We adopted laminating method through heating film and modules, guaranteeing warranty more than for 25 years. Also we are trying remote control systemically, not by hardware control, to run parallel with automatic driving and monitoring system which enable to control operation time, insolation, amount of snowfall automatically. We applied analysis of actual proof to both snow removal PV system and general PV power system, and these led to bear power consumption analysis while snow-removing, and its comparison after finishing the task as "One stone, two birds." In the long run, we could carry out economic analysis against snow removal system, and this helps to verify the most maximized control method for snow removal conditons on a basis of weather information. this study shall let prevent people from negligent accidents, and improve power generation problems as mentioned from the top. Ultimately, we expect to apply this system to heavy snowfall regions in winter season in spite of its limited system installaion in Korean territory, initially.

• 대한치과기공학회지
• /
• 제39권3호
• /
• pp.137-143
• /
• 2017

Purpose: The purpose of this study is to analyze the fitness of heat - pressed ceramic laminate veneers fabricated using the additive manufacturing. Methods: Impression was replicated by using light body silicone and heavy body silicone on the custom tray, and it was fabricated using Type IV Stone. The test specimens were prepared by using a dental scanner, a laminating veneer using a dental design program, and a specimen with a 3D printer. The control specimens were prepared by the lost wax technique and heat - pressed to fabricate the specimens. The data of the specimens were measured by the RMS value of the internal fitness a using a 3-dimensional measurement program. Results: The Stereolithography laminate veneer group was measured at $78.10(4.09){\mu}m$ and the LWV group was measured at $31.50(5.10){\mu}m$. There is a significant difference between the two groups (p<0.001) Conclusion : Evaluation of fitness laminate veneers was fabricated by additive manufacturing showed the difference statistically significantly and clinically acceptable result.

• 한국광학회지
• /
• 제20권4호
• /
• pp.241-248
• /
• 2009

액정 디스플레이에서 시야각 향상을 위해 사용하는 보상판과 편광판을 접합한 복합판의 광축 틀어짐 오차와 보상판의 $R_{in}$(in-plane retardation), $R_{th}$(out-of-plane retardation)를 동시에 결정하는 새로운 방법을 제시하였다. 보상판은 광축이 임의의 기울임각과 방위각을 갖는 o-판으로 하였으며, 확장된 존스 행렬법에 기반한 광학모델을 도입하여 복합판의 편광특성을 분석하였다. 입사각 0도와 50도에서 시료의 방위각을 360도 회전시키며 투과된 빛의 편광상태를 각각 계산한 후, 타원법의 모델링 분석기법을 적용하여 광축 틀어짐과 복합판의 기울임각과 방위각들을 역방계산하였다. 이 방법은 편광판과 보상판을 접합한 후에도 복합판의 성능평가를 할 수 있어 제조공정단계를 줄여 제조 원가를 절감하는데 기여할 수 있을 것으로 기대된다.

• 한국인터넷방송통신학회논문지
• /
• 제12권1호
• /
• pp.245-248
• /
• 2012

본 논문에서는 실리콘 기반의 기술과 차별화하여 저온동시소성세라믹 (LTCC) 기판을 이용하여 대표적 압전물질인 PZT 박막의 최적의 증착조건을 연구하였다. LTCC 기술은 실리콘 기반의 기술에 비하여 낮은 생산 단가, 높은 수율, 3차원 구조물의 용이한 제작성 등으로 인하여 센서 및 액추에이터와 같은 10 um ~ 수백 um 정도의 중규모 디바이스를 제작하는데 있어서 중요한 역할을 담당하고 있다. LTCC 기판은 NEG사의 MLS 22C 상용 파우더를 이용하여 100 um 두께의 그린쉬트를 적층하고 동시소결하여 400 um 두께로 제작하였다. 제작한 기판위에 Pt/Ti 하부전극을 증착하고 RF 마그네트론 스퍼터링 방법을 이용하여 PZT 박막의 증착조건을 연구하였다. 증착조건으로는 RF 전력과 아르곤과 산소 가스비를 가변하여 실시하였으며, XRD와 EDS를 사용하여 박막의 결정성 및 성분을 분석하였다. 실험을 통하여 얻어진 최적의 증착조건은 RF 전력 125W, 아르곤과 산소비 15:5에서 가장 우수한 특성을 나타내는 것을 확인하였다.

• 구강회복응용과학지
• /
• 제32권3호
• /
• pp.246-254
• /
• 2016

Direct metal laser sintering (DMLS) 방식은 3D 프린팅 중 한 방식으로, 재료를 쌓아가면서 레이저를 이용하여 선택적으로 sintering하는 방식이다. 이는 주조 방식에서 문제되는 결손과 뒤틀림을 방지할 수 있으며 절삭 가공 방식으로 제작하기 어려운 복잡한 구조물을 제작할 수 있다. 본 증례들은 DMLS 방식을 이용하여 지대치 간 길이가 긴 고정성 보철물, 포스트 등 다양한 고정성 보철물을 제작하여 수복하였고, 주기적인 관찰 결과 심미적, 기능적으로 만족할만한 결과를 얻었기에 이를 보고하는 바이다.

• 한국전기전자재료학회논문지
• /
• 제24권4호
• /
• pp.297-302
• /
• 2011

Recently, low temperature co-fired ceramic (LTCC) technology is widely used in sensors, actuators and microsystems fields because of its very good electrical and mechanical properties, high reliability and stability as well as possibility of making 3D micro structures. In this study, we investigated the effects of sputtering gas ratio and annealing temperature on the crystal structure of $Pb(ZrTi)O_3$ (PZT) thin films deposited on LTCC substrate. The LTCC substrate with thickness of $400\;{\mu}m$ were fabricated by laminating 4 green tapes which consist of alumina and glass particle in an organic binder. The PZT thin films were deposited on Pt / Ti / LTCC substrates by RF magnetron sputtering method. The results showed that the crystallization of the films were enhanced as increasing $O_2$ mixing ratio. At about 25% $O_2$ mixing ratio, was well crystallized in the perovskite structure. PZT thin films was annealed at various temperatures. When the annealing temperature is lower, the PZT thin films become a phyrochlore phase. However, when the annealing temperature is higher than $600^{\circ}C$, the PZT thin films become a perovskite phase. At the annealing temperature of $700^{\circ}C$, perovskite PZT thin films with good quality structure was obtained.

• 한국산업보건학회지
• /
• 제28권3호
• /
• pp.241-256
• /
• 2018

Objectives: This study aimed to review the characteristics of three-dimensional printing technology focusing on printing types, materials, and health hazards. We discussed the methodologies for exposure assessment on hazardous substances emitted from 3D printing through article reviews. Methods: Previous researches on 3D printing technology and exposure assessment were collected through a literature review of public reports and research articles reported up to July 2018. We mainly focused on introducing the technologies, printing materials, hazardous emissions during 3D printing, and the methodologies for evaluation. Results: 3D printing technologies can be categorized by laminating type. Fused deposition modeling(FDM) is the most widely used, and most studies have conducted exposure assessment using this type. The printing materials involved were diverse, including plastic polymer, metal, resin, and more. In the FDM types, the most commonly used material was polymers, such as acrylonitrile-butadiene-styrene(ABS) and polylactic acids(PLA). These materials are operated under high-temperature conditions, so high levels of ultrafine particles(mainly nanoparticle size) and chemical compounds such as organic compounds, aldehydes, and toxic gases were identified as being emitted during 3D printing. Conclusions: Personal desktop 3D printers are widely used and expected to be constantly distributed in the future. In particular, hazardous emissions, including nano sized particles and various thermal byproducts, can be released under operation at high temperatures, so it is important to identify the health effects by emissions from 3D printing. Furthermore, appropriate control strategies should be also considered for 3D printing technology.

• 패션비즈니스
• /
• 제18권3호
• /
• pp.73-90
• /
• 2014

Paper, once known and used only as a medium for printing or handicrafts, is now being used in new fields including artistic clothing, and an environment-friendly material for fashion, while the functionality of its formative characteristics and esthetics have been newly highlighted. On this basis, this study performed a content analysis of paper couture and categorization of types of paper modeling techniques based on 904 paper couture submitted to paper fashion shows, exhibitions and contest exhibits from 2001 to 2013. Analysis results showed that paper textile types were most common at 86.64%, while techniques using laminating, bonding, overlapping or paper as-is represented 62.17%. Expressive techniques in which paper was cut or torn and attached to paper clothing was 11.62%, paper folding was 5.75%, drawing and coloring 4.65%, and finally, paper cutting was 2.65%. Meanwhile, among paper modeling techniques using paper yarn textiles, a paper weaving technique was 6.75%. Moreover, other techniques in which paper modeling techniques or subsidiary clothing was blended were 3.65%, and Dak peeling textiles were 1.33%. Paper paste moulding textiles types represented 1.44%, above all papier $m{\hat{a}}ch{\acute{e}}$ techniques of 0.55% and creasing and holding techniques were 0.88%. Paper is sufficient to express the artists' creativity as well as having qualities as an artistic medium, such as variability through combined use with other materials, variation in form, suitability for reuse of waste paper, and environmental friendliness. Also, various paper modeling techniques can be blended with textiles for a generalized technology that overcomes the limits of paper and textiles.

• Composites Research
• /
• 제32권4호
• /
• pp.177-184
• /
• 2019

이미 제작된 복합재료 제품을 분석하여 층별로 어떤 기계적 물성을 가지는지 알아낼 수 있다면, 기존 제품에 비해 더 좋은 성능을 내는 복합재료 개발을 수행할 수 있게 된다. 본 연구에서는 프리프레그를 적층하여 제작된 복합재료 구조물에 대해 역설계 기법을 적용하여 내부 프리프레그 층의 물성을 계산하고자 하였다. 단순히 인장시험으로 얻어지는 물리량을 이용한 경우와 인장시험 및 모드 해석을 통해 얻어지는 물리량을 이용한 경우를 비교한 결과 후자의 정확도가 더 높음을 알 수 있었다. 최종적으로 예측된 $E_1$의 최대 오차는 0.09%였고 예측된 $E_2$의 최대 오차는 7%였다.