• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.2
• /
• pp.47-54
• /
• 2012

In this study, composite laminate cantilever type cylindrical shells with edge-stiffeners are analyzed. A versatile 4-node flat shell element which is useful for the analysis of shell structures is used. An improved flat shell element is established by the combined use of the addition of non-conforming displacement modes and the substitute shear strain fields. Two models by load conditions are considered. Load type A and B are loaded by point load at the free edge and line load respectively. A various parameter examples are presented to obtain proper stiffened length and stiffened thickness of edge-stiffeners. It is shown that the thickness of shell can be reduced minimum 30% by appropriate edge-stiffeners.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.1
• /
• pp.121-128
• /
• 1999

In this study, the behavior of R/C beams strengthened with carbon fiber laminate (CFL) is analyzed from the test results. CFL is attractive for this application due to its good tensile strength and low weight. Test parameters are the width and the thickness of CFL and repair of damaged specimen. The failure mode and ultimate load are analyzed from these measured data. Test results show that the peak load of specimens strengthened with CFL is increased to 1.27~2.04 times that of non-rehabilitation specimen. The wider lap width, larger amount of CFL, the larger strength is obtained. But the ductile behavior of the rehabilitated specimens is inversely proportional to the CFL thickness.

• Composites Research
• /
• v.14 no.6
• /
• pp.38-46
• /
• 2001

In this study, An optimization code that can design microwave absorbing composite laminates is developed, and 3-layered microwave absorbing composite laminates are developed by optimizing the thickness of each layer. The layers are 3 different composite laminates. Many variables including lay-up angles of electromagnetically orthotropic composite layer can be considered in this code. The developed laminate is composed of an impedance matching layer of glass/epoxy fabric laminate, a glass/epoxy fabric laminate layer containing aluminum filler and carbon/epoxy fabric laminate layer. Permittivities of the materials are obtained using a network analyzer and a coaxial air line.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.1
• /
• pp.41-52
• /
• 2001

In this paper the analysis of laminate composite folded plates with arbitrary angle connection like box girder is studied by finite strip method Total stiffness of laminated plate is obtained by integration of the stiffness in each layer or lamina through laminate thickness and total stiffness in each layer or lamina through laminate thickness and total tiffness matrix is obtained by substitutionto equilibrium equation derived from the minimum total potential energy theorem. The assumed displacement functions for a finite strip method in plate or box girder analysis are combinations of one-way polynomial functions in the transverse direction and harmonic functions in the span-wise direction. Finite strip method with the merits of the simplification in modeling and the reduction of analytical time is accurate in the analysis of laminate composite folded plates shaped like box firders.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.611-614
• /
• 2018

Laminate composites composed of $0.95Pb(Zr_{0.52}Ti_{0.48})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3$ piezoelectric ceramic and Fe-Si-B based magnetostrictive amorphous alloy are fabricated, and the effect of control of the areal dimensions and the thickness of the piezoelectric layer on the magnetoelectric(ME) properties of the laminate composites is studied. As the aspect ratio of the piezoelectric layer and the magnetostrictive layer increases, the maximum value of the ME voltage coefficient(${\alpha}_{ME}$) increases and the intensity of the DC magnetic field at which the maximum ${\alpha}_{ME}$ value appears decreases. Moreover, as the thickness of the piezoelectric layer decreases, ${\alpha}_{ME}$ tends to increase. The ME composites exhibit ${\alpha}_{ME}$ values higher than $1Vcm^{-1}Oe^{-1}$ even at the non-resonance frequency of 1 kHz. This study shows that, apart from the inherent characteristics of the piezoelectric composition, small thicknesses and high aspect ratios of the piezoelectric layer are important dimensional determinants for achieving high ME performance of the piezoelectric-magnetostrictive laminate composite.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.173-177
• /
• 2004

In this study, the effect of laminate thickness on the compressive behaviour of composite materials was investigated through systematic experimental work using the stacking sequences, [04]ns, [45/0/-45/90]ns and [45n/0n/-45n/90n]s (n = 2 to 8). The stacking sequence effects on failure strength of multidirectional laminates were examined. For this purpose, two different scaling techniques were used; (1) ply-level technique [45n/0n/-45n/90n]s and (2) sub laminate level technique [45/0/-45/90]ns. An apparent thickness effect existed in the lay-up with blocked plies, i.e. unidirectional specimens $([0_4]ns)$ and ply-level scaled multidirectional specimens ([45n/0n/-45n/90n]s). From the investigation of the stacking sequence effect, the strength values obtained from the sub laminate level scaled specimens were slightly higher than those obtained from the ply level scaled specimens. The measured failure strengths were compared with the predicted values

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.388-392
• /
• 2016

A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 laminate complex sheet. Two AA1050 and one AA6061 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 1.2 mm in thickness by conventional rolling. The rolling was performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 5.0 m/sec. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by natural aging T4) and artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age hardened Al complex sheets were revealed by optical microscope observation; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.9 times compared to that value of the starting material. In addition, the hardness of the complex sheets increased with cold rolling for AA1050 and age-hardening treatment for AA6061, respectively. After heat treatment, both AA1050 and AA6061 showed typical recrystallization structures in which the grains were equiaxed; however, the grain size was smaller in AA6061 than in AA1050.

• Korean Journal of Materials Research
• /
• v.26 no.3
• /
• pp.154-159
• /
• 2016

A roll-bonding process was applied to fabricate an AA1050/AZ91/AA1050 laminate complex sheet. Two AA1050 and one AZ91 magnesium sheets of 2 mm thickness, 30 mm width and 200 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 2 mm in thickness by conventional rolling. The rolling was performed at 623K without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 15.9 m/min. The AA1050/AZ91/AA1050 laminate complex sheet fabricated by roll bonding was then annealed at 373~573K for 0.5h. The microstructure of the complex sheets was revealed by electron back scatter diffraction (EBSD) measurement; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the complex sheet was found to increase by 11 % and the tensile elongation decreased by 7%, compared to those values of the starting material. In addition, the hardness of the AZ91 Mg region was slightly higher than those of the AA1050 regions. Both AA1050 and AZ91 showed a typical deformation structure in which the grains were elongated in the rolling direction; however, the mis-orientation distribution of grain boundaries varied greatly between the two materials.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.50-61
• /
• 2007

The structural stiffness, strength and stability on the bodyshell and floor structures of the Korean Low Floor Bus composed of laminate, sandwich panels and metal reinforced frame were evaluated. The laminate composite panel and facesheet of sandwich panel were made of WR580/NF4000 glass fabric/epoxy laminate, while aluminum honeycomb or balsa was applied to the core materials of the sandwich panel. A finite element analysis was used to verify the basic design requirements of the bodyshell and the floor structure. The use of aluminum reinforced frame and honeycomb core was beneficial for weight saving and structural performance. The symmetry of the outer and inner facesheet thickness of sandwich panels did not affect the structural integrity. The structural strength of the panels was evaluated using Von-Mises criterion for metal structures and total laminate approach criterion for composite structures. All stress component of the bodyshell and floor structures were safely located below the failure stresses. The total laminate approach is recommended to predict the failure of hybrid sandwich composite structures at the stage of the basic design.

• Steel and Composite Structures
• /
• v.18 no.3
• /
• pp.583-601
• /
• 2015

In the present study, the combined effects of thermal and mechanical loadings on the interlaminar shear stresses of both moderately thin and thick composite laminated beams are numerically analyzed. The finite element modelling of laminated composite beams and analysis of interlaminar stresses are performed using the commercially available software package MSC NASTRAN/PATRAN. The validity of the finite element analysis (FEA) is demonstrated by comparing the experimental test results obtained due to mechanical loadings under the influence of thermal environment with those derived using the present FEA. Various parametric studies are also performed to investigate the effect of thermal loading on interlaminar stresses generated in symmetric, anti-symmetric, asymmetric, unidirectional, cross-ply, and balanced composite laminated beams of different stacking sequences with identical mechanical loadings and various boundary conditions. It is shown that the elevated thermal environment lead to higher interlaminar shear stresses varying with the stacking sequence, length to thickness ratio, ply orientations under identical mechanical loading and boundary conditions of the composite laminated beams. It is realized that the magnitude of the interlaminar stresses along xz plane is always much higher than those of along yz plane irrespective of the ply-orientation, length to thickness ratios and boundary conditions of the composite laminated beams. It is also observed that the effect of thermal environment on the interlaminar shear stresses in carbon-epoxy fiber reinforced composite laminated beams are increasing in the order of symmetric cross-ply laminate, unidirectional laminate, asymmetric cross-ply laminate and anti-symmetric laminate. The interlaminar shear stresses are higher in thinner composite laminated beams compared to that in thicker composite laminated beams under all environmental temperatures irrespective of the laminate stacking sequence, ply-orientation and boundary conditions.