• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.8-13
• /
• 2015

Molded Case Circuit Breakers (MCCBs) are typically used to provide over current protection for electrical safety caused by short circuit faults and overloads in indoor low voltage power systems. The MCCB automatically connects and disconnects loads from the electrical source when the current reaches a value and duration that will cause an excessive. However, the MCCB sometimes is not interrupted due to a malfunction, nuisance tripping, or in a fire. Ensuring electrical safety is very important in a indoor low voltage power system. This paper presents the operating characteristics of MCCBs according to a temperature rise from room temperature to 160 degrees Celsius delivered by a radiant panel heater. The ABS 54c(rated current: 30A) of the hydraulic magnetic trip type was used in the experiments. The signals of temperature, voltage, and current were measured using the high accuracy Signal Conditioning Extensions for Instrumentation (SCXI) measurement system with the LabVIEW program manufactured by National Instruments. The operating characteristics were measured as functions of current amplitude and ramp-up rate. The MCCB tripping time decreased as a result of increasing current amplitude and ramp-up rate under a temperature rise condition, because the temperature and level of the current are directly proportional to the tripping time. Additionally, an instantaneous operation was observed after 8 times of the rated current, and the MCCB began to melt a surface temperature of around 300 degrees Celsius of. The experimental results coincided well with the operating curve.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.3
• /
• pp.639-646
• /
• 2016

In this study, the contactless measurement method with a optical displacement sensor(ODS, ADNS 9500) was proposed to overcome flaws in a rotary encoder based measurement under particular circumstances, such as a slippage and a case of little rotational inertia. The performance tests of the optical displacement sensor using data acquisition board and National Instruments's LabVIEW program were performed to accomplish accurate displacement measurements and the performance characteristics according to measurement direction, speed, acceleration, height and surface types were discovered through the repetitive tests. The experimental results indicate that, in order to get an accurate in-plane motion, the height(distance between the ODS and the target surface) has to be maintained at the range of 2.4 mm to 3.2 mm and the sensitivity(resolution) should be modified and applied to the formulae for displacement calculation, considering its measurement direction, speed and surface type.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.3
• /
• pp.53-63
• /
• 2006

The general objective of this study was to investigate biomechanical characteristics of bowling swing using three-dimensional cinematography. This study focused specifically on movements of the upper body segments during a bowling swing. Eight elite female bowling players participated in this study. Subjects performed bowling swing and their performance was sampled at 60 frame/sec using two high-speed video cameras with a synchronizer. After digitizing images from two cameras, the two-dimensional coordinates were used to produce three-dimensional coordinates of the 12 body segments (20 joint reference makers). The obtained three-dimensional coordinates were fed to a custom-written kinematic and kinetic analyses program (LabView 6.1, National Instrument, Austin, TX, USA). The analyses determined the linear and angular kinematic variables of the body segments with which joint force and torque of the lower and upper trunks and the shoulder were estimated based on the Newton-Euler equations. It was found that during the bowling swing the peak linear velocities of the body segments were reached in sequence the trunk, the shoulder, the elbow, the wrist, and the bowl. This result indicates that linear momentum of the lower body and the trunk transmits to the arm segment during the bowling swing. The joint torques of the torso and the arm occurred almost simultaneously, indicating that bowling swing seem to be a push-like motion, rather than a proximal-distal sequence motion in which many of throwing motions are categorized. The ultimate objective of the bowling swing is to release a heavy-weight bowl with power and consistency. Therefore, the bowling swing observed in this study well agrees with that bowlers use the stepping to increase the linear velocity of the bowl, the simple pendulum system and the push-like segmental motion in the torso and the arm segment to enhance the power at the release of the bowl.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.4
• /
• pp.105-113
• /
• 2006

The purpose of this study was to analyze the joint torque of triple segmental system in golf driver swing. For this purpose, joint torque were calculated. In order to determine the load on the lumbar region, a triple segmental system was set for wrist, left shoulder and lumbar, torque working on the lumbar region were estimated. For this study, a total of 7 professional golfers were sampled, and then, their driver swings were recorded with two high-speed digital video cameras (180 frames/sec.) to be synthesized into 3-dimensional images and coordinated. Then, Eular's equation was used to produce some kinematic data, which were used to calculate joint torque with Newton's function. All data were calculated using LabVIEW 6.1 graphic program. The results of this study can be summarized as follows; It was found that the joint torque was generated in the direction opposite the target on wrist and shoulder during down swing, while in the direction towards the target on the lumbar region. During impact and release, the torque on the wrist joint was converted from the direction opposite the target to the direction towards the target, while the torque on the lumbar region was generated vice versa. The joints on the club-arm-shoulder were generated in the opposite direction at the beginning of down swing when the torque on the thorax-pelvis began to be generated, and then, the torque on the thorax-pelvis began to lower, while that on the club-arm-shoulder began to increase. Thus, a rapid decrease of the torque on the lumbar region linked to the low trunk acted to increase moment and joint torque on the arm-club region.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.4
• /
• pp.49-59
• /
• 2006

The purpose of this study was to investigate the relations between the segments of the body, the three dimensional anatomical angle according to sweep shot in ice hockey. The subjects of this study were five professional ice hockey players. The reflective makers were attached on anatomical boundary line of body. For the movement analysis three dimensional cinematographical method(APAS) was used and for the calculation of the kinematic variables a self developed program was used with the LabVIEW 6.1 graphical programming(Johnson, 1999) program. By using Eular's equations the three dimensional anatomical Cardan angles of the joint and ice hockey stick were defined. 1. In three dimensional linear velocity of blade the Y axis showed maximum linear velocity almost impact, the X axis(horizontal direction) and the Z axis(vertical direction) maximum linear velocity of blade did not show at impact but after impact this will resulted influence upon hitting puck. 2. The resultant linear velocity of each segment of right arm showed maximum resultant linear velocity at impact. It could be suggest that the right arm swing patterns is kind of push-like movement. therefore the upper arm is the most important role in the right arm swing. 3. The three dimensional anatomical angular displacement of trunk in flexion-extension showed flexion all around the wrist shot. The angular displacement of trunk in internal-external rotation showed internal rotation angle at the backswing top and and increased the angle after the impact. while there is no significant adduction-abduction. 4. The three dimensional anatomical angular displacement of trunk showed most important role in wrist shot. and is follwed by shoulder joints, in addition the movement of elbow/wrist joints showed least to the shot. this study result showed upperlimb of left is more important role than upperlimb of right.

• Journal of Korean Society of Transportation
• /
• v.25 no.3
• /
• pp.99-109
• /
• 2007

Variable message signs (VMS), which are used for providing real-time information on traffic conditions and accident occurrences, are one of the important components of intelligent transportation systems VMS messages need to meet human factor requirements: messages should be readable and understandable while driving. Lab-controlled experiments on VMS messages were conducted to obtain useful data for analyzing drivers' responsive characteristics for VMS messages. Binary logistic regression (BLR) modeling techniques were applied to explore the relationships among drivers' message perceptions, message reading time, and amount of VMS messages. Probabilistic outcomes of the proposed BLR-based perception model could be greatly utilized to design VMS messages considering drivers' legibility performance. The major contribution of this study is to develop invaluable statistical models that can be used in designing VMS messages more effectively from the human factor point of view. The results could be further applied to establish the scheme of VMS message phase and duration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.942-945
• /
• 2003

Nerve gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas was dimethylmethylphosphonate($C_3H_9O_3P$, DMMP) that is simulant gas of nerve gas. Sensing material was $SnO_2$ added ${\alpha}-Al_2O_3$ with $4{\sim}20wt.%$ and was physically mixed. And then it was deposited by screen printing method on alumina substrate. Sensor device was consisted of sensing electrode with interdigit(IDT) type in front and heater in back side. Total size of device was $7{\times}10{\times}0.6mm^3$. Crystallite size of fabricated $SnO_2$ were characterized by X-ray diffraction(XRD, Rigaku) and morphology of the $SnO_2$ powders was observed by a scanning electron microscope(SEM, Hitachi). Fabricated sensor was measured as flow type and sensor resistance change was monitored real time using LabVIEW program. The best conditions as added $Al_2O_3$ amounts and operating temperature changes were 4wt.% and $300^{\circ}C$ in DMMP 0.5ppm, respectively. The sensitivity was over 75%. Response and recovery times were about 1 and 3 min., respectively. Repetition measurement was very good with ${\pm}3%$ in full scale.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.8-18
• /
• 2009

CableLAB published DOCSIS 3.0 Specifications to supply broadband access to homes and small businesses. The primary technique of DOCSIS 3.0 Specification is channel bonding which provides cable operators with a flexible way to significantly increase up/downstream speeds. In this paper, we propose the upstream scheduler that serves channel bonding. Proposed scheduler consists of two sub-scheduler: bonding group scheduler and channel scheduler. Also, we propose three scheduling algorithms to allocate request bandwidth of CM to each bonding channel: equivalent scheduling algorithm, current request-based scheduling algorithm, and last grant-based scheduling algorithm. In order to evaluate the performance of these algorithms and DOCSIS 3.0 MAC protocol, we develop the DOCSIS 3.0 simulator with the network simulator, OPNET, to model DOCSIS network, CMTS, and CM. Our results show that equivalent scheduling algorithm is superior to others in the view of transmission delay and throughput and DOCSIS 3.0 protocol provides higher throughput than pre-DOCSIS 3.0 protocol.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.398-406
• /
• 2013

Nuclear medicine imaging devices such as PET diagnose disease after injecting radiopharmaceuticals in human body for diagnosis. Radiopharmaceuticals should maintain the proper pH for human body safety. In general, pH paper is used to measure the pH of the radiopharmaceutical. pH of the sample compared with the standard color chart is used for measurement. However, the pH reading difference according to the experience of a rater can be generated. Also, a pH meter for measuring pH has a high sensitivity and contamination of the sensor must be avoided. In this paper, we developed the new hardware device for pH reading method and software was developed with vision algorithm to measure pH easily and simply.

• Journal of Korean Elementary Science Education
• /
• v.29 no.4
• /
• pp.505-514
• /
• 2010

This study aims to explore group inquiry using science writing heuristic in elementary school science. We observed and examined what elementary students experienced in their science classes and moreover how they used their data to support their claims in the view point of scientific epistemology. The research question of this study is 'what is the result of coherence measurement for figuring out the relationship between argument and ground in group inquiry activity?'. To solve the study question, one fifth-grade class at an elementary school was selected. Four lessons in group inquiry using a worksheet of science writing heuristic were videotaped and transcribed. It was found that the hours of group inquiry when students can discuss meaningfully occupied approximately 37 to 45%. When measuring coherence in each lesson by developing a scale from one to five to estimate the coherence of the work sheet designed, the total average was 3.424. It implicated that students had their claims supported by some of their evidences. Although the figure was not enough to assist that they found strong bonds between their claims and data, they started to move forward to epistemological approach in their science lab works.