• Journal of Engineering Education Research
• /
• v.3 no.2
• /
• pp.14-23
• /
• 2000

This paper is concerned with the development of remote engineering laboratory using the internet. Recently, various virtual laboratories are introduced using the multimedia technologies but the internet laboratory using the real hardware system is not present. In this study, we developed the remote engineering laboratory by combining the GPIB program which controls the hardwares with the web programming which controls the internet. The function generator, LCR meter, and oscilloscope were considered as the measurement devices. The client program includes the user-interface which carry out experiment remotely. Several electrical experiments were set up to verify the experimental process. It has been found that the remote engineering experiments are feasible and valid. The methodologies will be discussed in detail.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.51-56
• /
• 2017

In this paper, we have developed a differential pressure flow sensor designed as a single capacitive type. And the sensor was fabricated using a MEMS process. Differential pressure flow sensors are the most commonly used sensors for industrial applications. The sensing diaphragm and bonding joint of the MEMS pressure sensor are easily broken at high pressure. In this paper, we proposed a structure in which the diaphragm of the sensor was not broken at a pressure exceeding the proof pressure, and the differential pressure sensor was designed and manufactured accordingly. The operating characteristics of the sensor were evaluated at a pressure three times higher than the sensor operating pressure (0-3 bar). The developed sensor was $3.0{\times}3.0mm$ and measured with a LCR meter (HP 4284a) at a pressure between 0 and 3 bar. It showed 3.67 pF at 0 bar and 5.13 pF at 3 bar. The sensor operating pressure (0-3 bar) developed a pressure sensor with hysteresis of 0.37%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.313.2-313.2
• /
• 2013

본 연구에서는 기존에 연구된 Solar Cell 보다 구조 및 제작이 단순한 $Al/Al_2O_3/Si$(100) Solar cell을 제작하여 평가하였다. 기판으로는 p-type Si(100), 0.5~2 ${\Omega}{\cdot}cm$을 사용하여 chemical cleaning 후 ALD(Atom Layer Deposition)법으로 Al2O3 터널링 절연막을 증착하였으며, 박막의 두께를 1~10 nm로 변화시켜 MIS 커패시터의 터널링 효과를 평가하였다. MIS 커패시터의 전기적 특성평가를 위해 누설전류 밀도-전계 특성은 pA meter/DC Voltage source를 사용하였고, 커패시턴스-전압특성, D-factor 특성은 precision LCR meter를 사용하였다. $Al/Al_2O_3/Si$(100) Solar cell의 특성평가를 위해 300~1100nm 파장영역에 따른 양자 효율을 평가하기 위해 Quantum Efficiency system (QE)을 사용하였고, Stanard Test Conditions 100 $mW/cm^2$, AM1.5, $25^{\circ}C$ 조건의 Voc, Isc, Jsc, FF (Fill Factor) 및 Efficiency(%)를 평가하기 위해 Solar simulator를 이용하였다.

• Tribology and Lubricants
• /
• v.27 no.4
• /
• pp.209-212
• /
• 2011

The capacitive application(prove) can be used to measure the complex permittivity of dielectric material of various thickness and cross section. This paper presents that we designed the analysis system of engine oil permittivity to know the relation between the engine oil deterioration and the prove dimension. Each of the dimension of capacitive prove is changed and then electric capacity is measured by LCR {Inductance(L), Capacitance (C), and Resistance (R)} meter. The engine oil permittivity has extracted in the prove measurement. As the additional research, this paper suggest the best of the prove dimension for the permittivity measurement.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.142-142
• /
• 2003

The effects of film thickness on the dipolar relaxation of ferroelectric PbTiO$_3$ films were investigated in the microwave-frequency range. The dielectric constants ($\varepsilon$) and the dielectric losses (tan $\delta$) were successfully measured up to 30 ㎓ using interdigital capacitors. The PbTiO$_3$ thin films were deposited on the quartz substrate at room temperature and postannealed in oxygen atmosphere. As the film thickness increased, its grain size and tetragonality were enhanced. And the dipolar relaxation behavior began to appear in the thin films with approximately 20 nm thickness, since ferroelectric domains could not be formed hi small grains. The observed relaxation frequency (above 10 ㎓) was higher than the previous values reported in bulk ceramics. It can be correlated with the extremely small domain size of the thinfilms as shown by TEM. And, the Rayleigh constant [1] from domain wall motions was alsoinvestigated by LCR meter at 100 KHz.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.182-186
• /
• 2013

We studied the possibility that an air capacitor can be used as a humidity sensor by measuring capacitance change. In order to investigate the possibility, the change of capacitance of an air capacitor due to moisture in air was first considered theoretically, and was then experimentally verified. The capacitance was measured by an LCR impedance meter with a 100-kHz and 1-V ac. The results revealed that the changes in the experimentally measured capacitances were greater than those in the theoretically calculated values. Based on this fact, we knew that an air capacitor could be used as part of a humidity sensing device. We expect the humidity sensor with an air capacitor has characteristics of fast response time, high reliability, and high durability compared with other conventional methods.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.553-555
• /
• 2002

We were fabricated of rf power resisotor on AlN substrates by thick film process. The characteristics of capacitance and microwave are measured by digital LCR meter and Network analyzer(HP8532D). The results are shown that capacitances are slight greater and microwave characteristics are good values.

• Elastomers and Composites
• /
• v.24 no.3
• /
• pp.185-192
• /
• 1989

The thermal degradation of the homopolymer poly(methyl methacrylate)(PMMA)/tetra cyano quino dimethane(TCNQ) blend and Eccogel/TCNQ blend were carried out using the thermogravimetric method in the stream of nitrogen gas with 60ml/min at various heating rate from 1 to $20^{\circ}C/min$. Friedman and Ozawa mathermatical methods were used to obtain the value of activation energy. Produced electrical properties and activation energy by electric conductivity method that used LCR meter.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.240.1-240.1
• /
• 2011

본 연구에서는 펄스레이져 박막 증착법(Pulsed Laser Deposition;PLD)을 이용하여 연자성의 CoNiFe (CNF) 물질과 강유전 특성의$BaTiO_3$ (BTO) 물질을 다층박막 구조로 제작하여 약자장(H=200 Oe)에 의해 에너지를 집적 시키거나 유전상수를 조절하여 박막의 구조 변화에 따른 커패시턴스 변화를 연구하였다. 다양한 구조의 다층 박막은 Si/$SiO_2$/Ti/Pt(111) 기판상에 PLD을 이용하여 증착하였으며, Phillp's X-선 회절기 (XRD)를 이용하여 결정구조와 격자 상수를 결정하였다. FE-SEM, TEM, AFM 및 EDS를 이용하여 박막 표면/단면의 미세구조 및 물질에 따른 조성비를 확인하였다. 자기적 특성을 위해Vibrating Sample Magnetometer (VSM)를 측정하였고, 전기적 특성은 LCR meter를 이용하여 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.234-234
• /
• 2008

Chemically homogeneous $Ba_{0.6}Sr_{0.4}TiO_3$ (BST) sols were synthesized using barium acetate, strontium acetate, and titanium isoproxide as starting materials. BST thin films of thickness 340 nm were deposited on Pt/$TiO_2/SiO_2$/Si and alumina substrates using spin coating method. The technique used for the processing of these films was Ultraviolet (UV) sol-gel photoannealing, using phto-sensitivity precursor solutions and UV-assisted rapid thermal processing(UV-RTP). The crystallization behaviour of the BST sols and thin films was studied by differential thermal analysis (DTA) and X-ray diffraction (XRD). Variation of permittivity and dielectric loss were measured in LCR-meter, model HP 4394A.