• Proceedings of the Acoustical Society of Korea Conference
• /
• 1993.06a
• /
• pp.229-232
• /
• 1993

이 논문은 최근에 개발된 실시간 음성부 검출 알고리즘[1]을 TMS320C30 System board와 IBM PC486을 이용한 implementation에 관한 논문이다. 음성부 검출 알고리즘은 Energy와 LCR(Level Crossing Rate)를 이용하여 각 frame을 음성/묵음으로 분류하는 방법을 사용하였고 DSP 보드를 사용하여 한 frame이 입력되면 다음 frame이 입력되기 전에 그 frame에 대한 음성/묵음 분류를 하여 음성입력이 끝남과 동시에 음성이라고 판단되는 부분만을 DPS moemory상에 저장하므로 불필요한 memory의 낭비를 중이고 다음 단계의 음성처리를 위한 시간을 절약하였다. 이 알고리즘의 성능 평가를 위하여 Rabiner와 Sambur의 알고리즘과 한민수의 알고리즘과를 전문가가 수작업으로 찾아낸 결과와 비교 평가하였다. 알고리즘의 오차는 평균 남성 4.925ms, 여성 5.85ms로 1 frame 이내의 오차를 보였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.21-24
• /
• 2003

휴대이동전화의 고성능화, 소형화에 따라서 전자부품들은 고집적화가 요구되고 있다. 이에 따라서 많은 수의 수동부품을 회로 기판 내에 내장화하기 위한 LTCC(Low Temperature Cofired Ceramic: 저온동시소성)기술이 적용된 부품의 출현이 계속되고 있다. 본 연구에서는 이러한 저온동시소성 기술을 활용하여 제품을 개발하기 위해서 고주파수 대역의 소자의 특성을 측정 하였다. 측정된 소자의 특성을 적용하기 위해서 소자 쿠폰을 제작하으며 고주파 회로 분석과 시뮬레이션 결과를 통해서 수동소자가 내장된 PAM( 전력증폭기), FBAR용 모듈 기판을 제작하였다.

• Tribology and Lubricants
• /
• v.27 no.4
• /
• pp.209-212
• /
• 2011

The capacitive application(prove) can be used to measure the complex permittivity of dielectric material of various thickness and cross section. This paper presents that we designed the analysis system of engine oil permittivity to know the relation between the engine oil deterioration and the prove dimension. Each of the dimension of capacitive prove is changed and then electric capacity is measured by LCR {Inductance(L), Capacitance (C), and Resistance (R)} meter. The engine oil permittivity has extracted in the prove measurement. As the additional research, this paper suggest the best of the prove dimension for the permittivity measurement.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.142-142
• /
• 2003

The effects of film thickness on the dipolar relaxation of ferroelectric PbTiO$_3$ films were investigated in the microwave-frequency range. The dielectric constants ($\varepsilon$) and the dielectric losses (tan $\delta$) were successfully measured up to 30 ㎓ using interdigital capacitors. The PbTiO$_3$ thin films were deposited on the quartz substrate at room temperature and postannealed in oxygen atmosphere. As the film thickness increased, its grain size and tetragonality were enhanced. And the dipolar relaxation behavior began to appear in the thin films with approximately 20 nm thickness, since ferroelectric domains could not be formed hi small grains. The observed relaxation frequency (above 10 ㎓) was higher than the previous values reported in bulk ceramics. It can be correlated with the extremely small domain size of the thinfilms as shown by TEM. And, the Rayleigh constant [1] from domain wall motions was alsoinvestigated by LCR meter at 100 KHz.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.182-186
• /
• 2013

We studied the possibility that an air capacitor can be used as a humidity sensor by measuring capacitance change. In order to investigate the possibility, the change of capacitance of an air capacitor due to moisture in air was first considered theoretically, and was then experimentally verified. The capacitance was measured by an LCR impedance meter with a 100-kHz and 1-V ac. The results revealed that the changes in the experimentally measured capacitances were greater than those in the theoretically calculated values. Based on this fact, we knew that an air capacitor could be used as part of a humidity sensing device. We expect the humidity sensor with an air capacitor has characteristics of fast response time, high reliability, and high durability compared with other conventional methods.

• Tribology and Lubricants
• /
• v.12 no.1
• /
• pp.22-28
• /
• 1996

This study was undertaken to investigate the dry wear characteristics and mechanism of KP-4M steel for plastic molding against SKD 61 hardened by heat treatment. The wear test was carried out under different conditions such as sliding speed, contact pressure, sliding distance, with frictional tester of pin on disc type. The wear loss on variation of sliding speed was little in lower speed range below 0.5 m/sec and in higher speed range above 1.5 m/sec,'but wear loss was high in intermediate speed range. The critical sliding speed, which showed the maximum value of specific wear rate, became lower with increased contact pressure. Increasing the contact pressure, the critical sliding distance Lcr which the wear mechanism changes from severe wear to mild wear was increased due to the decrease of oxidation reaction velocity. Through this study we suggested a model of generation and elimination process of wear debris of KP-4M steel for plastic molding.

• Korean Journal of Mathematics
• /
• v.17 no.3
• /
• pp.283-291
• /
• 2009

We investigate the existence of multiple solutions (${\xi},{\eta}$) for perturbations of the parabolic system with Dirichlet boundary condition $$(0.1)\;\begin{array}{lcr}{\xi}_t=-L{\xi}+g_1(3{\xi}+{\eta})-s{\phi}_1-h_1(x,t)\;in\;{\Omega}{\times}(0,\;2{\pi}),\\{\eta}_t=-L{\eta}+g_2(3{\xi}+{\eta})-s{\phi}_1-h_2(x,t)\;in\;{\Omega}{\times}(0,\;2{\pi}).\end{array}$$ We show the existence of multiple solutions (${\xi},{\eta}$) for perturbations of the parabolic system when the nonlinearity $g^{\prime}_1,\;g^{\prime}_2$ are bounded and $3g^{\prime}_1(-{\infty})+g^{\prime}_2(-{\infty})<{\lambda}_1,\;{\lambda}_n<3g^{\prime}_1(+{\infty})+g^{\prime}_2(+{\infty})<{\lambda}_{n+1}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.553-555
• /
• 2002

We were fabricated of rf power resisotor on AlN substrates by thick film process. The characteristics of capacitance and microwave are measured by digital LCR meter and Network analyzer(HP8532D). The results are shown that capacitances are slight greater and microwave characteristics are good values.

• Elastomers and Composites
• /
• v.24 no.3
• /
• pp.185-192
• /
• 1989

The thermal degradation of the homopolymer poly(methyl methacrylate)(PMMA)/tetra cyano quino dimethane(TCNQ) blend and Eccogel/TCNQ blend were carried out using the thermogravimetric method in the stream of nitrogen gas with 60ml/min at various heating rate from 1 to $20^{\circ}C/min$. Friedman and Ozawa mathermatical methods were used to obtain the value of activation energy. Produced electrical properties and activation energy by electric conductivity method that used LCR meter.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.240.1-240.1
• /
• 2011

본 연구에서는 펄스레이져 박막 증착법(Pulsed Laser Deposition;PLD)을 이용하여 연자성의 CoNiFe (CNF) 물질과 강유전 특성의$BaTiO_3$ (BTO) 물질을 다층박막 구조로 제작하여 약자장(H=200 Oe)에 의해 에너지를 집적 시키거나 유전상수를 조절하여 박막의 구조 변화에 따른 커패시턴스 변화를 연구하였다. 다양한 구조의 다층 박막은 Si/$SiO_2$/Ti/Pt(111) 기판상에 PLD을 이용하여 증착하였으며, Phillp's X-선 회절기 (XRD)를 이용하여 결정구조와 격자 상수를 결정하였다. FE-SEM, TEM, AFM 및 EDS를 이용하여 박막 표면/단면의 미세구조 및 물질에 따른 조성비를 확인하였다. 자기적 특성을 위해Vibrating Sample Magnetometer (VSM)를 측정하였고, 전기적 특성은 LCR meter를 이용하여 측정하였다.