• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.557-563
• /
• 2014

This study deals with a resonant converter of an anti-start air conditioner compressor for commercial vehicles. The anti-start air conditioner compressor must generally have a high current, high efficiency, a low volume, and a low weight. To reduce the switching losses and voltage and current stresses of the device, the anti-start air conditioner compressor applies the full-bridge L-C resonant converter topology. Hardware parameters are designed to have a wide voltage range, and the switching frequency range of the L-C resonant converter is determined. Simulation is implemented using PSIM and an experiment is performed to verify the proposed converter.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.311-314
• /
• 2003

In this paper, proposed circuit proposes that Active-Clamp-Circuits basis of a current-fed inverter linked type high frequency resonant dc-dc converter of conventional. and the paper the most of characteristics of the reduced high voltage stress main switches with active clamp circuits and output current constant with the resonant part consists of L, C resonant tank circuit. Also, the capacitor (C$_1$, C$_2$) connected in switches are a common using by resonance capacitor and ZVS capacitor. and circuit analysis used state equation of each part modes. Also we conform a rightfulness theoretical analysis by comparing a parameters values and simulation values obtained from simulation using Power MOS-FET as switching devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.976-980
• /
• 2001

In this study, P $b_{0.88}$(L $a_{a}$N $d_{l-a}$)$_{0.08}$(M $n_{1}$3/S $b_{2}$3/)$_{0.02}$ $Ti_{0.98}$ $O_3$system ceramics were manufactured for 20 MHz class resonator application. Electromechanical coupling factor, mechanical quality factor and dynamic range of 3rd overtone thickness vibration mode were measured as the variations of La and Nd molar ratio. Mechanical quality factor and dynamic range at $\alpha$=0.6 composition ceramics showed the highest value of 2, 691 and 52.37 dB, respectively. The tempearture coefficient of resonant frequency measured from -2$0^{\circ}C$ to 8$0^{\circ}C$ showed an excellent value of 5ppm/$^{\circ}C$ at $\alpha$ = 1 composition ceramics. ceramics.s.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.86-93
• /
• 2003

This paper describes that the resonant tank type DC-DC converter consist of reactor and capacitor resonant tank circuit for increased the output current. This circuit configuration is composed of the resonant tank circuit used resonant capacitor and reactor and the capacitor connected in switch are a common using by resonance capacitor and ZVS(Zero Voltage Switching) capacitor. Therefore, the proposed converter can reduce a switching losses, noise, and voltage stress at turn-on and turn-on and has an advantage which is able to operating safely in load short, because DC reactor is connected with resonance reactor in order to supply a fixed current with low ripple from DC power supply. The analysis of proposed circuit uses normalized parameters and characteristic estimation is generally described the proposed circuit with the characteristics of power and output voltage etc. Also, design is based on the characteristic estmations in each step. Hence, We conform a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1026-1028
• /
• 2001

In this paper, proposal circuit proposes that load parallel resonant DC-DC Converter consist of L and C resonant tank circuit. Also, the capacitor$(C_1,\;C2)$ connected in switch are a common using by resonance capacitor and ZVS capacitor. The analysis of proposed circuit uses normalized parameter and characteristic estimation which is needed in each step before design is generally described the proposed circuit with the characteristics of average power and average output voltage etc. Alse, we conform a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.4
• /
• pp.326-333
• /
• 2004

This research proposes a high frequency resonant inverter for high power conversion apparatus, which is consist of two L-C linked full-bridge inverter using MOSFET in order to distribute voltage and current of the devices. As an output power control strategy, the time sharing control method is applied. From the computer simulation results, the inverters and devices can be shared properly voltage and current rating of the system. And also, theoretical characteristics of the proposed circuit are compared with experimental results.

• Geomechanics and Engineering
• /
• v.28 no.1
• /
• pp.25-33
• /
• 2022

The energy transferred on drill rods by dynamic impact mainly determines the penetration depth for in-situ tests. In this study, the dynamic response and transferred energy of drill rods are determined from the frequency of the stress waves. AW-type drill rods of lengths 1 to 3 m are prepared, and strain gauges and an accelerometer are installed at the head and tip of the connected rods. The drill rods are hung on strings, allowing free vibration, and then impacted by a pendulum hammer with fixed potential energy. Increasing the rod length L increases the wave roundtrip time (2L/c, where c is the wave velocity), and hence the transferred energy at the rod head. At the rod tip, the first velocity peak is higher than the first force peak because a large and tensile stress wave is reflected, and the transferred energy converges to zero. The resonant frequency increases with rod length in the waveforms measured by the strain gauges, and fluctuates in the waveforms measured by the accelerometer. In addition, the dynamic response and transferred energy are perturbed when the cutoff frequency is lower than 2 kHz. This study implies that the resonant frequency should be considered for the interpretation of transferred energy on drill rods.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.189-192
• /
• 2002

In this study, The experimental open-tube-type and close-tube-type thermoacoustic refrigerator were constructed. The resonant characteristics of a thermoacoustic refrigerator were investigated. In order to determine the optimum resonant tube length and frequency, We changed the length of resonant tube from 400mm to 850mm and the frequency from 100Hz to 1000Hz. In case of first harmonic, the temperature difference of open-tube-type (1/4 wave) refrigerator was $41^{\circ}C$(resonator length :500mm). The temperature difference of close-tube-type (1/2 wave) refrigerator was $43^{\circ}C$(resonator length :850mm). In this experiments, the experimental 1/2 wave refrigerator is slightly cooler than the experimental l/4 wave refrigerator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.5.2-8
• /
• 1995

0.15($Ba_{1-x}Sr_{x}$)O-$0.15Sm_2O_3$-$0.7TiO_2$(x=0∼9[m/o]ceramics were fabricated by mixed-oxide method. Microwave dielectric properties were investigated with sintering conditions aid Sr addictive. In the specimen with x=0[m/o] sintered at 1350∼1470[$^{\circ}C$], dielectric constant, quality factor and temperature coefficient of resonant frequency were 70∼74, 2800∼3300(at 3[GHz]), -1.33∼+l.66[ppm/$^{\circ}C$, respectively. Increasing the Sr additive from 0 to 5[m/o], dielectric constant and temperature coefficient of resonant frequency were increased and quality factor was decreased. In the specimen with x=r[m/o] sintered at 1375[$^{\circ}C$], 6[hr], dielectric constant, quality factor and temperature coefficient resonant frequency were 75.62, 2785(at 3[GHz]), +8.39[ppm/$^{\circ}C$], respectively.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1225-1229
• /
• 2018

In this paper, we investigated the electronic structures and defect states of $SrLaMgTaO_6$ (SLMTO) double perovskite structures by using resonant inelastic x-ray scattering. Recently, $Eu^{3+}$ doped SLMTO red phosphors have been vigorously investigated due to their higher red emission efficiency compared to commercial white light emitting diodes (W-LED). However, a comprehensive understanding on the electronic structures and defect states of host SLMTO compounds, which are specifically related to the W-LED and photoluminescence (PL), is far from complete. Here, we found that the PL spectra of SLMTO powder compounds sintered at a higher temperature, $1400^{\circ}C$, were weaker in the blue emission regions (at around 400 nm) and became enhanced in near infrared (NIR) regions compared to those sintered at $1200^{\circ}C$. To elucidate the difference of the PL spectra, we performed resonant inelastic x-ray spectroscopy (RIXS) at Ta L-edge. Our RIXS result implies that the microscopic origin of different PL spectra is not relevant to the Ta-related defects and oxygen vacancies.