• 대한치과보철학회지
• /
• 제57권2호
• /
• pp.127-133
• /
• 2019

목적: 본 연구의 목적은 주조 금속 포스트, 기성 섬유강화형 포스트 그리고 치과영역에서 새롭게 주목 받고 있는 재료인 polyetherketoneketone(PEKK)으로 제작한 포스트로 수복된 근관 치료 치아의 파절 강도 및 파절 양상에 대해 조사하는 것이다. 재료 및 방법: 총 21개의 하악 소구치를 포스트 재료에 따라 각각 7개씩 3개의 군으로 무작위로 분류하였다. 그룹 A는 주조 금속 포스트 코어; 그룹 B는 기성 섬유강화형 포스트 및 레진 코어; 그룹 C는 밀링된 PEKK 포스트 코어로 수복하였다. 모든 시편은 금속관으로 수복하였다. 각각의 시편들을 제작 후 만능 시험기를 사용하여 2 mm/min 속도로 치아 장축에 대해 135도의 정적 하중을 가하여 파절 강도를 측정하고, 파절 양상에 대해 조사하였다. 결과 분석은 유의수준 ${\alpha}=.05$에서 Kruskal-Wallis test 후 사후검정으로 Mann-Whitney U test를 시행하였다. 결과: PEKK 포스트 파절 강도는 주조 금속 포스트와 기성 섬유강화형 포스트에 비해 낮은 값을 보였다. 파절양상에 있어서는 육안과 현미경, 방사선 사진을 통해 살펴본 결과 금속 포스트 코어에서는 치근파절의 양상이 대부분 나타난 반면 기성 섬유 강화형포스트는 포스트의 탈락이 주로 발생하였다. PEKK 포스트 코어의 경우 치아와 포스트가 함께 파절되는 양상이 주로 나타났다. 결론: 치관부 치질이 심하게 손상된 치아 수복 시 적절한 재료의 선택이 필요하며, PEKK 포스트의 임상적 적용을 위해서는 강도 향상에 대한 연구가 더 필요할 것으로 보인다.

• 대한치과보철학회지
• /
• 제34권2호
• /
• pp.349-362
• /
• 1996

To determine the factors to affect on stone surface porosities produced from hydrogen gas of additional silicone, both putty and syringe type of 7 commercially different additional silicone impression materials(Blend-A-Scon, Correct VPS, Exaflex, Express, Extrude, Provil, Reprosil) were chosen and NewFujirock(GC) was poured into the impressions of detail-reproducing test block at 1, 15, 30, 45, 60 minutes after the impression materials had set and 4 specimens were made for each pouring time, each type of impression material, and each consisency and So, 280 specimens were made in total. The number of surface porosities of same area($2826 mm^2$) which were typically caused by hydrogen gas using the stereoscope(X 7.5) by two observers. Comparison of putty-syringe type and among the impression materials are tested by Kruscal-Wallis method and Mann-Whitney method(p<0.05). The results are as follows. 1. The number of porosities decreased as the pouring time of stone was delayed on both putty and syringe type of additional silicone materials. 2. The putty type significantly produced more porosities than syringe type except for the group of Reprosil.(p<0.05). 3. In case of putty type, the number of porosities increased as following order. Reprosil / Blend-A-Scon and Provil / Correct VPS and Extrude / Express and Exaflex. 4. In case of syringe type, Blend-A-Scon and Extrude produced no porosity and Exaflex and Provil at 30 minites, but Express produced porosities even at 60 minutes and the most. Additional silicone impression material releases hydrogen gas, and that fact can make the resulting die stone model useless. So, to minimize these adverse effects, it is desirable not to expose putty type of additional silicone on critical impression surface because putty type has a tendency to produce more porosities than syringe type. And it is important to have sufficient time before pouring the stone on impression because porosities produce less as time passes after setting of impression material. Also, there are differences among 7 additional silicone impression materials, so it is desirable to choose adequate brand of additional silicone for good laboratory work.

• Restorative Dentistry and Endodontics
• /
• 제27권3호
• /
• pp.249-256
• /
• 2002

The use of flowable composite resins as liners in class II packable composite restoration has been suggested by some manufacturers. However, the contributions of this technique are unproven. The purpose of this study was to compare the gingival microleakage in class II packable composite restorations with or without the use of flowable composite resins as liners. Slot cavities were prepared on both proximals of 80 extracted human molars and randomly assigned to 8 groups of 20 each. The gingival margins were located at 1mm above CEJ in 80 cavities (group1-4) and 1mm below CEJ in 80 cavities (group5-8). The prepared teeth were mounted in the customized tray with adjacent teeth to simulate clinical conditions and metallic matrix band (Sectional matrix) and wooden wedges were applied. After acid etching and application of Single Bond, each group was restored with the following materials using incremental placement technique: Group 1,5 (Filtek P60), group 2, 3, 4 and group 6, 7, 8 (AeliteFlo, TetricFlow, Revolution/ Filtek P60). All specimens were thermocycled 500 times between 5$^{\circ}C$ and 55$^{\circ}C$ with 1 mimute dwell time, immersed 2% methylene blue dye for 24 hours and then rinsed with tab water. The specimens were embedded in clear resin and sectioned longitudinally through the center of restoration with a low speed diamond saw. Dye penetration at gingival margin was viewed at 20 magnification and analyzed on a scale of 0 to 4. Kruscal-Wallis One way analysis and Mann-Whitney Rank sum test were used to analyze the results. The results of this study were as follows. 1. The leakage values seen at the enamel margin were significantly lower than those seen at the dentin margin(P<0.05). 2. On the enamel margin, packable composite resins with flowable liners showed lower leakage than those without flowable liners, but there were no significant differences among the four groups(P>0.05). 3. On the dentin margin, four groups demonstrated moderate to severe leakage, and there were no significant differences in leakage values(P>0.05).

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.46-55
• /
• 2000

During bonding procedure of composite resin, the prepared cavity can be contaminated by saliva. In this study, marginal microleakage and shear bond strength of a composite resin to primed enamel and dentin treated with artificial saliva(Taliva$^{(R)}$) were evaluated. For the marginal microleakage test, Class V cavities were prepared in the buccal surfaces of fifty molars. The samples were randomly assigned into 5 groups with 10 samples in each group. Control group was applied with a bonding system (Scotchbond$^{TM}$ Multi-Purpose plus) according to manufacture's directions without saliva contamination. Experimental groups were divided into 4 groups and contaminated with artificial saliva for 30 seconds after priming: Experimental 1 group ; artificial saliva was dried with compressed air only, Experimental 2 group ; artificial saliva was rinsed and dried. Experimental 3 group ; cavities were etched with 35% phosphoric acid for 15 seconds after rinsing and drying artificial saliva. Experimental 4 group ; cavities were etched with 35% phosphoric acid for 15 seconds and primer was reapplied after rinsing and drying artificial saliva. All the cavities were applied a bonding agent and filled with a composite resin (Z-100$^{TM}$). Specimens were immersed in 0.5% basic fuschin dye for 24 hours and embedded in transparent acrylic resin and sectioned buccolingually with diamond wheel saw. Four sections were obtained from one specimen. Degree of marginal leakage was scored under stereomicroscope and their scores were averaged from four sections. The data were analyzed by Kruscal-Wallis test and Fisher's LSD. For the shear bond strength test, the buccal or occlusal surfaces of one hundred molar teeth were ground to expose enamel(n=50) or dentin(n=50) using diamond wheel saw and its surface was smoothed with Lapping and Polishing Machine(South Bay Technology Co., U.S.A.). Samples were divided into 5 groups. Treatment of saliva-contaminated enamel and dentin surfaces was same as the marginal microleakage test and composite resin was bonded via a gelatin capsule. All specimens were stored in distilled water for 48 hours. The shear bond strengths were measured by universal testing machine (AGS-1000 4D, Shimaduzu Co., Japan) with a crosshead speed of 5 mm/minute. Failure mode of fracture sites was examined under stereomicroscope. The data were analyzed by ANOVA and Tukey's studentized range test. The results of this study were as follows : 1. Enamel marginal microleakage showed no significant difference among groups. 2. Dentinal marginal microleakages of control, experimental 2 and 4 groups were lower than those of experimental 1 and 3 groups (p<0.05). 3. The shear bond strength to enamel was the highest value in control group (20.03${\pm}$4.47MPa) and the lowest value in experimental 1 group (13.28${\pm}$6.52MPa). There were significant differences between experimental 1 group and other groups (p<0.05). 4. The shear bond strength to dentin was higher in control group (17.87${\pm}$4.02MPa) and experimental 4 group (16.38${\pm}$3.23MPa) than in other groups, its value was low in experimental 1 group (3.95${\pm}$2.51 MPa) and experimental 2 group (6.72${\pm}$2.26MPa)(p<0.05). 5. Failure mode of fractured site on the enamel showed mostly adhesive failures in experimental 1 and 3 groups. 6. Failure mode of fractured site on the dentin did not show adhesive failures in control group, but showed mostly adhesive failure in experimental groups. As a summary of above results, if the primed tooth surface was contaminated with artificial saliva, primer should be reapplied after re-etching it.

• 치위생과학회지
• /
• 제11권5호
• /
• pp.389-395
• /
• 2011

본 연구는 치위생과 학생들이 가지고 있는 성취동기가 어떠한지를 파악하고, 성취동기에 영향을 미치는 요인을 알아보기 위해 2010년 3월부터 2010년 6월까지 약 4개월에 걸쳐 3개 대학의 치위생과 재학생을 편의추출하여 자료를 수집하였고 설문지 421부를 분석에 사용한 결과 다음과 같은 결론을 얻었다. 1. 대상자의 일반적 특성에서 졸업 후 예상되는 근무기간을 보면 '결혼 후에도 계속 하겠다'가 78.4%로 가장 높게 나타났으며, 해외진출에 대한 나의 의지에 대한 질문에는 '상황에 따라 결정하겠다' 47.7%, '즉시 가겠다' 29.2%, '경력을 쌓은 후 가겠다' 22.6%로 나타났고 치위생학에 대한 나의 생각에 있어서는 대체로 긍정적이었다. 2. 치위생과 학생의 성취동기는 3.34점으로 나타났으며, 가장 높은 점수를 보인 문항은 '주어진 일은 책임감 있게 수행한다' 3.78점이었고, 가장 낮은 점수를 보인 문항은 '약간 위험이 따르는 일을 좋아한다' 2.67점으로 나타났다. 3. 대상자의 일반적 특성에 따른 성취동기를 보면 학년이 높을수록(p<0.001), 임상실습경험이 있을수록(p<0.01), 졸업 후 예상하는 근무기간에 따라서는 '결혼 후 재취업하겠다'고 응답한 경우 높게 나타났다(p<0.05). 또 해외진출에 대한 의지는 해외진출에 대한 강한 의지를 가진 사람일수록 (p<0.001), 성격이 긍정적일수록(p<0.001), 상황이나 환경변화에 대해서도 적응을 잘 할수록 성취동기가 높게 나타났다(p<0.001). 4. 대상자의 일반적 특성이 성취동기에 미치는 영향을 살펴본 결과, 다른 변수들이 통제된 가운데 학년이 증가할수록(p<0.01), 졸업 후 예상되는 근무기간에서 '결혼 시까지 하겠다'(p<0.01), '결혼 후 계속하겠다' (p<0.05)는 생각을 가지지 않을수록 치위생과 학생들의 성취동기는 커지는 것으로 나타났다. 본 연구를 통해 치위생과 학생들의 성취동기는 대체로 높은 편이었으며, 학년이 증가할수록, 졸업 후 예상되는 근무기간이 길수록 성취동기는 높아지는 것을 알 수 있었다. 따라서 치위생과 학생들의 성취동기를 높이기 위해서는 재학 중에 치과위생사에 대한 긍정적 마인드를 심어주고, 재학 중에 노력한 결과 본인이 목표한 곳에 취업하여 성공적으로 일하고 있는 선배들의 사례를 통해 본인도 그렇게 할 수 있다는 진취적인 생각을 할 수 있도록 지도해야 할 것으로 생각된다.

• Restorative Dentistry and Endodontics
• /
• 제27권2호
• /
• pp.142-149
• /
• 2002

Low-viscosity composite resins may produce better sealed margins than stiffer compositions (KempScholte and Davidson, 1988: Crim, 1989). Plowable composites have been recommended for use in Class V cavities but it is also controversial because of its high rates of shrinkage. On the other hand, in the study comparing elastic moduli and leakage, the microfill had the least leakage (Rundle et at. 1997) Furthermore, in the 1996 survey of the Reality Editorial Team, microfills were the clear choice for abfraction lesions. The purpose of this study was to evaluate the microleakage of 6 compostite resins (2 hybrids, 2 microfills, and 2 flowable composites) with and without load cycling. Notch-shaped Class V cavities were prepared on buccal surface of 180 extracted human upper premolars on cementum margin. The teeth were randomly divided into non-load cycling group (group 1) and load cycling group (group 2) of 90 teeth each. The experimental teeth of each group were randomly divided into 6 subgroups of 15 samples. All preparations were etched, and Single bond was applied. Preparations were restored with the following materials (n=15) : hybrid composite resin [Z250(3M Dental Products Inc. St. Paul, USA), Denfil(Vericom, Ahnyang, Korea)], microfill [Heliomolar RO(Vivadent, Schaan, Liechtenstein), Micronew(Bisco Inc. Schaumburg, IL, USA)], and flowable composite［AeliteFlo(Bisco Inc. Schaumburg, IL, USA), Revolution(Kerr Corp. Orange, CA, USA)]. Teeth of group 2 were subjected to occlusal load (100N for 50,000 cycles) using chewing simulator(MTS 858 Mini Bionix II system, MTS Systems Corp. Minn. USA). All samples were coated with nail polish 1mm short of the restoration, placed in 2％ methylene blue for 24 hours, and sectioned with a diamond wheel. Enamel and dentin/cementum margins were analyzed for microleakage on a sclale of 0 (no leakage) to 3 (3/3 of wall). Results were statistically analyzed by Kruscal-Wallis One way analysis, Mann-Whitney U-test, and Student-Newmann-Keuls method. (p = 0.05) Results : 1. There was significantly less microleage in enamel margins than dentinal margins of all groups (p＜0.05) 2. There was no significant between six composite resin in enamel margin of group 1. 3. In dentin margin of group 1, flowable composite had more microleakage than others but not of significant differences. 4. there was no significant difference between six composite resin in enamel margin of group 2. 5. In dentin margin of group 2, the microleakage were R＞A =H=M＞D＞Z. But there was no significant differences. 6. In enamel margins, load cycling did not affect the marginal microleakage in significant degree. 7. In enamel margins, load cycling did affect the marginal microleakage only in Revolution. (p＜0.05).

• 대한방사선치료학회지
• /
• 제26권1호
• /
• pp.43-50
• /
• 2014

두경부암 환자의 헤드 홀더를 사용하는 경우 모의 치료 시 환자는 테이블 위에 위치하지만, 방사선 치료를 시행하는 경우 헤드 홀더를 치료 테이블에 걸쳐서 사용하기 때문에 체중 및 여러 가지 요소로 인한 기하학적 불일치로 상, 하, 좌, 우 및 처짐의 현상이 발생할 수 있다. 이러한 환자 Set-Up의 재현성의 불일치를 개선하기 위해 두경부암 전용 헤드 홀더를 자체 고안하여 제작 및 개발하여 유용성을 평가하였다. Alderson Rando Phantom을 이용하여 전산화단층촬영장치(High Advantage, GE, U.S.A)를 통해 이미지를 획득하였고, 광자선 4MV 세기변조 방사선치료(IMRT) 방식을 적용하여 최적화된 치료 계획을 실시하였다. 선형가속기(21EX, Varian, U.S.A)를 이용하여 모의 치료와 동일한 상태에서 환자를 set-up한 후 에 치료기에 장착된 CBCT를 이용하여 각각의 무게(0,15,30Kg)의 차이를 통해 교정 전, 후 X, Y, Z축의 오차를 5회 반복 측정한 결과는 다음과 같다. 0Kg에서 $0.4{\pm}0.8mm$, $0.8{\pm}0.4mm$, 0mm으로 나타났고, 교정 후에는 $0.2{\pm}0.8mm$, $0.4{\pm}0.5mm$, 0으로 나타났다. 15Kg에서 교정 전,후 오차는 $0.2{\pm}0.8mm$, $1.2{\pm}0.4mm$, $2.2{\pm}0.4mm$와 $0.2{\pm}0.4mm$, $0.4{\pm}0.5mm$, $0.4{\pm}0.5mm$로 나타났다. 30Kg에서 교정 전,후 오차는 $0.8{\pm}0.4mm$, $2.4{\pm}0.5mm$, $4.4{\pm}0.8mm$와 $0.6{\pm}0.54mm$, $1{\pm}0mm$, $0.6{\pm}0.5mm$로 나타났다. 각각의 교정 전,후의 통계적으로 분석한 결과 15Kg인 경우 Z축에서 p<0.034, 30Kg인 경우 Y, Z축에서 p<0.038, p<0.041 로 유의한 결과를 나타냈다. 두경부암 전용 방향 조절 장치 헤드 홀더가 환자의 set-up오차를 줄여주는 역할을 해주는 것으로 나타났다. 또한 오차를 줄여줌으로써 환자의 재현성이 향상되어 보다 정밀하고 정확한 방사선 치료를 구현할 수 있을 것으로 사료된다.