• Journal of Soil and Groundwater Environment
• /
• v.11 no.3
• /
• pp.12-19
• /
• 2006

In this study, the stability of Ca-bentonite colloids from Gyeongju area was studied by investigating the changes in the size of the bentonite colloids using a dynamic light scattering method depending on the geochemical conditions such as pH and ionic strength. Kinetic and equilibrium coagulation behavior of the bentonite colloids was investigated by changing the pH and ionic strength of the bentonite suspensions. The results showed that the stability of the bentonite colloids strongly depended upon contact time, pH, and ionic strength. It was also shown that the bentonite colloids were unstable at higher ionic strength greater than 0.01 M $NaClO_4$ at whole pH values considered. In addition, the stability ratio Wand the critical coagulation concentration (CCC) were also calculated using the data from the kinetic coagulation experiments. The stability ratio W was decreased as the ionic strength increased and varied with pH depending on the ionic strength. The CCC of the Ca-bentonite colloids was about 0.05 M $NaClO_4$ around pH 7.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.3
• /
• pp.329-338
• /
• 2019

Suction of unsaturated bentonite buffers is a very important input parameter for hydro-mechanical performance assessment and design of an engineered barrier system. This study analyzed suction measurement techniques and constitutive models of unsaturated porous media reported in the literature, and suggested suction measurement techniques and constitutive models suitable for bentonite buffer in an HLW repository. The literature review showed the suction of bentonite buffer to be much higher than that of soil, as measured by total suction including matric suction and osmotic suction. The measurement methods (RH-Cell, RH-Cell/Sensor) using a relative humidity sensor were suitable for suction measurement of the bentonite buffer; the RH-Cell /Sensor method was more preferred in consideration of the temperature change due to radioactive decay heat and measurement time. Various water retention models of bentonite buffers have been proposed through experiments, but the van Genuchten model is mainly used as a constitutive model of hydro-mechanical performance assessment of unsaturated buffers. The water characteristic curve of bentonite buffers showed different tendencies according to bentonite type, dry density, temperature, salinity, sample state and hysteresis. Selection of water retention models and determination of model input parameters should consider the effects of these controlling factors so as to improve overall reliability.

• Nuclear Engineering and Technology
• /
• v.31 no.2
• /
• pp.139-150
• /
• 1999

The swelling pressure of a potential buffer material was measured and the effect of dry density, bentonite content and initial water content on the swelling pressure was investigated to provide the information for the selection of buffer material in a high-level waste repository. Swelling tests were carried out according to Box-Behnken's experimental design. Measured swelling pressures were in the wide range of 0.7 Kg/$\textrm{cm}^2$ to 190.2 Kg/$\textrm{cm}^2$ under given experimental conditions. Based upon the experimental data, a 3-factor polynomial swelling model was suggested to analyze the effect of dry density, bentonite content and initial water content on the swelling pressure The swelling pressure increased with an increase in the dry density and bentonite content, while it decreased with increasing the initial water content and, beyond about 12 wt.% of the initial water content, levelled off to nearly constant value.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.2
• /
• pp.40-45
• /
• 1999

This study deals with an investigation on low cost adsorbents locally available n dyeing wastewater treatment of color removal. Peat, bentonite, slag and fly ash were utilized for this study. Considering that low cost adsorbents contained in $SiO_2$, $Fe_2O_3$ and $Al_2O_3$ compositions, and coagulants were mainly used aluminate and ferrate in color removal. Color of dyeing wastewater was high removed in peat, berntonite and slag except for fly ash with passed time. It could be known that color removal of peat and slag were increased to pH 4, but was hardly changed with advancing to alkaline. Color intended to be high removed with increasing of agitation speed but to be almost slow after 150rpm. As a result on the experiment of Freundlich adsorption isotherms, adsorption intensity(l/n) appeared to be peat>fly ash>slag>bentonite and adsorption capacity(k) came out peat>bentonite>slag>fly ash. Therefore, if low cost adsorbents substituted for existing adsorbents, peat, bentonite and slag could look forward to an expected economical effect.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.6
• /
• pp.493-500
• /
• 2006

This paper concerns the measurement of thermal conductivity of grouting materials for ground loop heat exchanger. A thermal conductivity meter, QTM-500 based on modified transient hot wire method was used to measure the thermal conductivity of neat bentonite and mixtures of bentonite and various additives. Relative to the total mixture mass, as the percent additive was increased the mixture thermal conductivity increased. For the bentonite-silica sand mixtures, the higher density of the sand particles resulted in much higher mixture thermal conductivity. The quartzite and silica sands produced the largest increases in mixture thermal conductivity, while common masonry and limestone sands produced lower thermal conductivity increases.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.5
• /
• pp.773-786
• /
• 2018

In this paper, viscosity features of sealant (bentonite-cement slurry), which is used for umbrella arch method in tunnel, were studied. The sealant must secure optimal strength and capacity for the waterproof and stabilization of borehole as well as to satisfy groutability. In this study, the variation of viscosity was measured with different mixing processes. With an increase of initial mixing period with water and bentonite mixture, the required time for the rapid increase of viscosity of the sealant is shorten. With increase of mixing period, the possibility of swelling of bentonite will increases and this can lead increase of the viscosity of the mixture. In addition, the behaviors of sealant vary with a drastic increase of the viscosity: thixotropy and rheopexy. Furthermore, the bentonite/water mixing period influences on the bleeding features of the sealant. Further study is required to introduce the guideline, which can be applicable in the field in the aspect of required capacity of the sealants and mixing processes of the ingredients.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.97-104
• /
• 2017

A bentonite mixing with local soil widely used as liner layer for landfill should have low permeability less than $1{\times}10^{-7}cm/s$. But there are several limitations of bentonite used as liner layer, such as drying shrinkage cracking, ineffective waterproof ability under salt water condition like flocculation under sea water. The purpose of this research is the development of a salt resistance bentonite by mixing sepiolite and guar gum to overcome the weak points of bentonite to get high water resistance capacity and permeability coefficient below $1{\times}10^{-7}cm/s$ under salt water condition. After having performed drying shrinkage cracking test, swelling index test, compaction test, and hydraulic conductivity test we confirmed the optimal mixing ratio of materials and evaluated the performance of materials.

• Tunnel and Underground Space
• /
• v.32 no.1
• /
• pp.30-58
• /
• 2022

The deep geological repository for high-level radioactive waste disposal is a multi barrier system comprised of engineered barriers and a natural barrier. The long-term integrity of the deep geological repository is affected by the coupled interactions between the individual barrier components. Erosion and piping phenomena in the compacted bentonite buffer due to buffer-rock interactions results in the removal of bentonite particles via groundwater flow and can negatively impact the integrity and performance of the buffer. Rapid groundwater inflow at the early stages of disposal can lead to piping in the bentonite buffer due to the buildup of pore water pressure. The physiochemical processes between the bentonite buffer and groundwater lead to bentonite swelling and gelation, resulting in bentonite erosion from the buffer surface. Hence, the evaluation of erosion and piping occurrence and its effects on the integrity of the bentonite buffer is crucial in determining the long-term integrity of the deep geological repository. Previous studies on bentonite erosion and piping failed to consider the complex coupled thermo-hydro-mechanical-chemical behavior of bentonite-groundwater interactions and lacked a comprehensive model that can consider the complex phenomena observed from the experimental tests. In this technical note, previous studies on the mechanisms, lab-scale experiments and numerical modeling of bentonite buffer erosion and piping are introduced, and the future expected challenges in the investigation of bentonite buffer erosion and piping are summarized.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.63-73
• /
• 2019

In this study, it was studied recycled soils with bentonite-polymer mixture in order to design economic landfill instead of clay liner. Recycled soil was used as SP, a sandy soil with 90.58% sand and 1.88% silt and clay. The recycled soils were mixed with 4%, 6%, and 8% bentonite by weight, and then compared with samples mixed with 2%, 3%, and 4% bentonite by weight in marine clay. Recycled soil satisfied the permeability criteria at 8%, and clay soil satisfied at 3%. In order to make a sample that satisfies the standard of the waste landfill, a permeability test was conducted by mixing 0.16%, 0.24%, and 0.28% of the polymer in a sample having 4% bentonite mixing ratio. The unconfined compression strength test was carried out at the same mixing ratio to confirm that the specification was satisfied. As the bentonite mixture ratio increased, the permeability coefficient and unconfined compression strength decreased. The strength in polymer mixing increased initially and then maintained a constant value. At 4% bentonite mixing ratio and 0.28% polymer mixing ratio, the coefficient of permeability was 1.0×10^-7 cm/sec or less, and the unconfined compression strength was over 500 kPa. It was confirmed that it can be used as a mixed liner material of waste landfills.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.1
• /
• pp.69-74
• /
• 1977

This study has been conducted to identify physico-chemical and clay mineralogical characteristics of bentonites produced in Korea for the purpose of finding good quality bentonite for agricultural ure. The results are summarized as follows: 1. Bentonites are mainly composed of montmorillonite developed from tuffs in a lava flow. 2. Chemical properties of bentonites are: pH in $H_2O$(1:1), 7:cation exchange capacity, 60-96me/100g; content of $SiO_2$, 54-72%; ratio of $SiO_2$ to $Al_2O_3$, 4.1-10.0;oven dry loss of $H_2O$ is higher than the ingnition loss of $H_2O$. 3. The x-ray diffrection patterns of powder bentonites show peaks at $14-15{\AA}$, $4.4{\AA}$, and $2.5{\AA}$, and that of swellen one show $17{\AA}$ when treated with ethylene glycol. 4. Distribution areas of the good quality bentonites were (1) Dogu-Dong, Donghae-Myeon, Yeonil-Gun, Gyeongsangbug-Do (2) Hamyeon-Ri, Yangnam-Myeon, Weolseong-Gun, Gyeongsanbug-Do. (3) Joam-Ri, Gangdong-Myeon, Weolseong-Gun, Gyeongsangbug-Do. (4) Sanha-Ri, Gangdong-Myeon, Ulju-Gun, Gyeongsangnam-Do. (5) Sinhyeon-Ri, Gangdong-Myeon, Ulju-Gun, Gyeongsangnam-Do. (6) Yonghang-Ri, Pyeongchang-Myeon, Pyeongchang-Gun, Gangweon-Do.