• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.652-660
• /
• 2008

For the recycling of rapid-chilled steel slag, the mechanical strengths and physical properties of EVA-polymer modified mortars with the various replacement ratios of rapid-chilled steel slag were investigated. Twenty five specimens of polymer modified mortars were prepared with the five different amounts of EVA-polymer modifier (0, 5, 10, 15, 20 wt%) and rapid-chilled steel slag (0, 25, 50, 75, 100 wt%). For the investigation of the characteristics of polymer modified mortars, the measurements such as water-cement ratio, unit volume weight, air content for fresh mortar and compressive strength, flexural strength, water absorption, hot water resistance, porosity and SEM investigation for curing specimens were conducted. As a results, with an increase in the replacement ratio of rapid-chilled steel slag, water-cement ratios decreased but unit volume weight increased remarkably. With increasing EVA-polymer modifier and the replacement ratio of rapid-chilled steel slag, percent of water absorption decreased but compressive and flexural strengths increased remarkably. By the hot water resistance test, mechanical strengths decreased but total pore volume and porosity increased remarkably. In the SEM observation, the components of specimen were shown to stick to each other in the form of co-matrix phase before hot water resistance test, but polymer modifier of co-matrix phase was decomposed or deteriorated after hot water resistance test.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.279-287
• /
• 2007

An ore of stone obtained from quarry lose its about 60% such as the muck and the stone-dust during the process of making the architectural block, the crushed aggregate and so on. A part of the muck is only reutilized for the crushed aggregate as road pavement materials, while the most of the muck in the shape of powder is mixed with water and then it is deposited in a sludge tank. The muck in the shape of powder is called the stone-dust. If the stone-dust is discharged and sprayed, an ecosystem will have terrible damage because the seepage of surface water, the flow of ground water and the movement of air are not occurred smoothly by packing the void of soils. As the Waste Management Law (2003) in Korea, the stone-dust is sorted out the industrial waste and the most of that is dumped in ground. Therefore, the establishments of an efficient recycling plan are necessary through the improvement of engineering properties of the stone-dust. To investigate the possibility of recycle and improvement for the stone-dust, the stone-dust and natural soils are sampled from six quarries in Korea. The various soil tests are performed by use of the mixed soils with the stone-dust content ratio. As the result of various soil tests, the recycle possibility of the stone-dust is analyzed as subbase layer materials of the roads.

• Journal of Wetlands Research
• /
• v.16 no.4
• /
• pp.433-441
• /
• 2014

It has been known that sewage containing high-concentration nitrogen affects the efficiency of municipal wastewater treatment plants harmfully. Therefore, research has been actively conducted to treat sewage containing high-concentration nitrogen. The current study has analyzed organic compounds, conducted foaming tests, and operated a laboratory-level nitritation reactor with the subjects of anaerobic digester supernatant and livestock wastewater which are the typical kinds of sewage containing high-concentration nitrogen. According to the results of analyzing organic compounds, soluble inert components form the largest part of anaerobic digester supernatant while particle biodegradable components occupy the most part of livestock wastewater. About the retention time proper for the reaction of nitritation, anaerobic digester supernatant shows 2 days while livestock wastewater indicates 6 days. It seems that the difference in the proper retention time is resulted from the difference of properties in organic compounds and ammonium nitrogen concentration. In addition, livestock wastewater's reactor foam is generated comparatively more than anaerobic digester supernatant's, but it tends to be eliminated faster. It is expected that the findings of this study can be utilized as foundational data afterwards in applying the reaction of nitritation to municipal wastewater treatment plants.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.449-457
• /
• 2020

Due to the improvement of living standards and avoidance of the 3D industry, it is difficult to find young and competent domestic workers at construction sites, and most foreign workers are contributing to the replacement, but the quality is still deteriorating due to lack of skilled workers and aging. Precast method is a method that make members in factory and assembles them on site, which can be expected to improve labor force and quality. This study is intended to provide basic data for the development of hang-type PC beams that can be applied to the determination of the field application of developed PC beams. The U-type connecting material is installed on both ends of the hang-up PC beam, and the role of the U-type connecting material is very important because it is a simple construction method through the U-type connecting material. In addition, the performance of the U-type connecting material will determine the performance of the hang-type PC beam as the final destruction occurs in the hang-type PC beam. The material properties of U-type connecting material were identified through structural experiments, and the end test corresponding to the partial experiment was conducted based on the material test results identified. Finally, the final design value of PC beams was proposed through structural experiments for application to the site.

• Journal of Conservation Science
• /
• v.37 no.5
• /
• pp.567-578
• /
• 2021

In this study, the physicochemical properties of 21 wall fragments and rooftile pieces excavated from Jeseoksa Dump-site were analyzed, and the possibility of heat exposure, such as the fire reported in the literature, was investigated by estimating the firing temperature. From the results, it was estimated that the rooftiles were composed of refined materials, and the walls were composed of materials having different particle sizes depending on the layer. Unlike ordinary rooftiles and walls, they exhibited an uneven surface with traces of bloating phenomenon in the cross section. It was estimated from the blackening of some portions that firing was not performed in a controlled state in a constant firing environment. In addition, the estimated firing temperature showed that the non-overfired rooftiles had endured a firing temperature of 900℃ or less, but the over-fired samples were subjected to a temperature of 1,000℃ or higher and were fired at a temperature higher than the manufacturing temperature at that time. Additionally, the rooftiles probably became defective during firing or molding at the time of production, but the non-overfired rooftiles exhibited an intact shape and showed the possibility of heat exposure due to fire. Therefore, the analytical results of this study confirm that the defective architectural components damaged by the fire, as reported in the literature, were discarded in the Jeseoksa dump-site.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.6
• /
• pp.243-249
• /
• 2018

Ceramic tiles, which were manufactured through high-temperature firing process at over $1000^{\circ}C$, are widely used as interior and exterior materials for building construction due to their excellent durability and aesthetic of surface glaze. In recent years, the introduction of digital ink-jet printing in ceramic tiles for architectural use has been rapidly proceeding, and studies on the materials such as ceramic ink, ceramic pigment, glaze have been actively conducted. In this study, the effect of microstructure change of surface glaze on the printing properties of ceramic inks was investigated by micronization of kaolin, which is the raw material of surface glaze. Black ceramic ink was used for ink-jet printing on the surface glaze of ceramic tile to evaluate the printability by measuring the size and roundness of the printed ink dot. The relationship between microstructure change of surface glaze and printability of ceramic ink was also investigated by analyzing the surface roughness and internal micropore distribution of surface glaze.

• Korean Journal of Heritage: History & Science
• /
• v.45 no.3
• /
• pp.174-193
• /
• 2012

This study focused on distribution ratio of stone properties based on material characteristic analysis, provenance presumption and transportation route interpretation of the Sungnyemun stone block foundation. The stone block foundation is composed of pinkish granite (56.0%), reddish granite (4.5%) and leucocratic granite (26.2%) of original stones and pinkish granite of new stones(13.3%). The rock-forming minerals for granites are consisted mainly of quartz, alkali-feldspar, plagioclase and biotite, and are similar geochemical evolution trend of major, rare earth, compatible and incompatible elements. Therefore, it is clear that the rocks are genetically same origin. As a result of magnetic susceptibility measurement, the pinkish and reddish granite of original stones and pinkish granite of new stones showed normal distribution around about 4.00(${\times}10^{-3}SI\;unit$). But the leucocratic granite of original stones were confirmed ilmenite series under about 1.00(${\times}10^{-3}SI\;unit$). As a result of provenance interpretation and transportation route analysis based on the petrological results, the provenance of pinkish granite and reddish granite of original stones are presumed the north slope in Namsan mountain and Naksan mountain. Also, the leucocratic granite of original stones and the pinkish granite of new stones are strongly possible furnished from the south and north slope in Namsan mountain and Naksan mountain, respectively.

• Korean Journal of Construction Engineering and Management
• /
• v.22 no.2
• /
• pp.31-41
• /
• 2021

The purpose of this study is to analyze the properties of previous studies related to vocations in the construction field. The results of the analysis are as follows. First, The paper has not been published at the beginning of the establishment of the academic foundation for vocational studies, but there was a marked increase over the next 15 years. Second, research related to vocations in the construction field has been more active in engineering than in social science. Third, the primary data method was used much more than the secondary data method, and the quantitative research method through a questionnaire was the most common research method. Fourth, human objects showed the highest frequency as 78.9%, and among them, technicians was the most. Fifth, as the research topic, psychological and behavioral aspects such as job satisfaction, job stress, turnover intention, and organizational commitment were dealt with most, and structural and environmental aspects such as national job competency standards, job analysis, construction accidents, and career development. It was also found that the topic of the research was actively being dealt with.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.585-596
• /
• 2022

The purpose of this study is to propose an assessment method to analyze clay collectively referred to as fine particles of clay components contained in fine aggregates, and to propose quality standards for clay use through correlation with the performance of concrete to verify the properties of clay measured according to the method. As a result, it is analyzed that it will be suitably utilized as a method to assess the fine particles of the clay component of fine aggregates through the component analysis of XRF. Regarding the related quality standards, considering the error rate of about 10% of KCS 14 20 10, the related quality standards were analyzed to be safe when Al₂O₃+Fe₂O₃+MgO is 23.5% or less and SiO₂+K₂OSiO₂+K2₂O is 66.5% or more. To build on this study, it is expected that a comprehensive review will be conducted through additional follow-up studies such as on clay of coarse aggregates and durability analysis to establish a system for quality control of the soil fraction of aggregates.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.421-425
• /
• 2023

The smoke properties of some plastics were investigated, including polymethyl methacrylate (PMMA), polycarbonate (PC), polyvinyl chloride (PVC), and polyacetal. For smoke density, related values of static smoke characteristics were measured using a smoke density tester according to ISO 5659-2. In addition, combustion with and without flame was measured independently. Under the condition of radiant heat of 50 kW/m² using the flame method, the measured value of the maximum specific optical density (D_m) of smoke showed the lowest value for PMMA (401.26) and the highest value for PVC (1345.04). In addition, PMMA (262.82) was the lowest and PVC (1385.43) was the highest in the measured D_m of smoke under the condition of radiant heat of 50 kW/m² in the non-flame method. Smoke generation during combustion of the object is significantly affected by the radiant heat flux, and carbonizable plastics showed a higher amount of smoke than non-carbonizable plastics during combustion. Polymers with aromatic groups in the main polymer chain generated a large amount of smoke because a large amount of char was generated due to thermal decomposition.