• 로봇학회논문지
• /
• 제6권1호
• /
• pp.27-33
• /
• 2011

Control and trajectory generation of a 7 DOF anthropomorphic robot arm suffer from computational complexity and singularity problem because of numerical inverse kinematics. To deal with such problems, analytical methods for a redundant robot arm have been researched to enhance the performance of inverse kinematics. In this research, we propose an analytical inverse kinematics algorithm for a 7 DOF anthropomorphic robot arm. Using this algorithm, it is possible to generate a trajectory passing through the singular points and intuitively move the elbow without regard to the end-effector pose. Performance of the proposed algorithm was verified by various simulations. It is shown that the trajectory planning using this algorithm provides correct results near the singular points and can utilize redundancy intuitively.

• 제어로봇시스템학회논문지
• /
• 제9권12호
• /
• pp.1026-1032
• /
• 2003

A biped walking robot which is developed as a platform for researching walking algorithm is briefly introduced. The developed walking robot has 6 degrees of freedom per one leg. The origins of the last three axis do not intersect at a point, so the kinematic analysis is cubmersome with the conventional method. In the former version of the robot, Jacobian-based inverse kinematics method is used. However, the Jacobian-based inverse kinematics method has drawbacks for the application in which knee is fully extended such as stair-case walking. The reason far that is the Jacobian becomes ill-conditioned near the singular points and the method is not able to give adequate solutions. So, a method for giving a closed-form inverse kinematics solution is proposed. The proposed method is based on careful consideration of the kinematic structure of the biped walking robot.

• 한국정밀공학회지
• /
• 제20권4호
• /
• pp.103-111
• /
• 2003

The Denavit-Hartenberg symbolic notation provides the framework for the convenient and systematic method for the robot manipulator kinematics, but is limited its use to the lower pair mechanism or to the single loop mechanisms. The Sheth-Uicker notation is its revised and generalized version to be extended fur the entire domain of the link mechanism including the higher pairs. This paper proposes the method that uses the Sheth-Uicker notation fur the robot kinematics modeling. It uses the instantly coincident coordinate system and the closed loop chain fur the coordinate transformation. It enables us to model the velocity kinematics of the robot that has the complex structures such as the ternary links and the wheels in a systematic and rational way. As an implementation of the proposed method, the Jacobian matrices were obtained for not only the robot with two legs and a torso, but a manipulator on a mobile platform.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.1-7
• /
• 2008

This paper describes the kinematics which is a new type of parallel manipulator, and the neural network is applied to solving the forward kinematics problem. The parallel manipulator called it as a Stewart platform has an easy and unique solution about the inverse kinematics. However, the forward kinematics is difficult to get a solution because of the lack of an efficient algorithm caused by its highly nonlinearity. This paper proposes the neural network scheme of an Newton-Raphson method alternatively. It is found that the neural network can be improved its accuracy by adjusting the offset of the obtained result.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.150-160
• /
• 1995

The practical design and construction of a Stewart Platform-based unilateral universal hand-controller is presented. It is also presented that such a design concept could be implemented by developing a technical method of determining the forward kinematics of a Stewart Platform in real time. In this work, the forward kinematics of a Stewart Platform has been determined in real time using three additional displacement sensors which eliminate the computational burden of solving the forward kinematics described in nonlinear simultaneous equations. The workspace of the Stewart Platform via inverse kinematics has been analyzed numerically and used as a design guide for the determination of the mechanism dimensions such as the sizes of the upper and base platforms and the minimum and maximum lengths of the legs. The hardware of the hand-controller has been constructed and tested to demonstrate the feasibility of the design concept.

• 한국정밀공학회지
• /
• 제29권1호
• /
• pp.64-71
• /
• 2012

In this paper, a parallel manipulator is comprised of two sliders and four links. Sliders execute a linear reciprocating motion depending on parallel guides and make the connected links rotate. A couple of links connected by sliders do coupling motion. The end-effector called a link tip has orientation angle. Through the kinematics analysis of this manipulator, we found displacement, velocity and acceleration using direct and inverse kinematics. We used equations that derived from this analysis and determined five constraint conditions. These conditions had much to do with rotation states of links, the relative relation of link length and coupling motion state. To verify those, we suggest a new algorithm regarding constraint conditions of a manipulator. With the result which performed the algorithm, we found out that operation range of coupled links was limited by relative relation of link length and that manipulator was not able to carry out a series of link motion, in case of being the link vertical between two parallel guides.

• 한국게임학회 논문지
• /
• 제4권4호
• /
• pp.19-24
• /
• 2004

본 연구에서는 수학적 지식이 요구되는 기존의 역운동학 해법을 사용하지 않고 직관력이 높은 기하학 방식의 새로운 역운동학 해법을 제시하였다. 뼈대 2개로 구성된 역운동학 모듈은 뼈대가 꺾이는 방향의 3차원 벡터만을 제공하여 수학적 지식이 없이도 역운동학의 사용이 가능했다. 본 연구에서 제시한 방법은 수학적 지식이 요구되지 않기 때문에 좀더 많은 그래픽 디자이너들이 역운동학을 쉽게 사용할 수 있을 것이다.

• 한국컴퓨터그래픽스학회논문지
• /
• 제5권1호
• /
• pp.11-17
• /
• 1999

Example guided inverse kinematics (EGIK)는 기존의 역운동학(inverse kinematics)을 확장, 향상시키는 알고리즘이다. 기존의 역운동학은 모델자체의 redundancy에 기인하여 jerky한 동작을 만들어내는 단점이 있다. EGIK에서는 미리 측정된 동작데이타를 효과적으로 이용하여 이러한 redundancy문제를 해결한다. 이 때 end-effector 위치 차이와 관절각의 차이를 동시에 최소화하기 위해서 비선형 최적화 기술이 사용된다. 우리는 결과로서의 동작이 원래의 동작의 특성을 잘 보존하는 자연스러운 것임을 보인다. EGIK는 기존의 동작 데이타를 이용하여 다관절체의 동작을 생성해내는 효과적인 기술이다.

• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.414-430
• /
• 1996

In this paper, a new kinematic structure of a parallel manipulator with six Cartesian degrees of freedom is proposed. It consists of a platform which is connected to a fixed base by means of 3-PPSP(parameters P, S denote the prismatic, spherical joints) subchains. Each subchain has a link which is concected to a passive prismatic joint at the one end and a passive spherical joint at the other. The spherical joint is then attached to perpendicularly arranged prismatic actuators which are fixed at the base. The spherical joint is then attached to perpendicularly arranged prismatic actuators which are fixed at the base. This arrangement provides a basis to control all six Cartesian degrees of motion of the platform in space. Due to its efficient architecture, the colsed-form solutions of the inverse and forward kinematics can be obtained. As a consequence, this new kinematic structure can be servo controlled using simple inverse kinematics becaese forward kinematics allows for measuring the platform's position and orientation in Cartesian space. Furthermore, the proposed structure provides an effective functional workspace. Series of simulations are performed to verify the results of the kinematics analyses.

• 대한의용생체공학회:의공학회지
• /
• 제29권6호
• /
• pp.431-435
• /
• 2008

Quantitative information of a three dimensional(3D) kinematics of joint is very useful in knee joint surgery, understanding how knee kinematics related to joint injury, impairment, surgical treatment, and rehabilitation. In this paper, an automated 2D/3D image matching technique was developed to estimate the 3D in vivo knee kinematics using dual X-ray images. First, a 3D geometric model of the knee was reconstructed from CT scan data. The 3D in vivo position and orientation of femoral and tibial components of the knee joint could be estimated by minimizing the pixel by pixel difference between the projection images from the developed 3D model and the given X-ray images. The accuracy of the developed technique was validated by an experiment with a cubic phantom. The present 2D/3D image matching technique for the estimation of in vivo joint kinematics could be useful for pre-operative planning as well as post-operative evaluation of knee surgery.