• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.89-97
• /
• 2018

The test results of a 7-tonf-class engine for the third-stage engine of KSLV-II are presented. Hot-firing tests performed with two engineering model engines are classified into ground tests and high-altitude tests according to the test conditions. The operability verification of the engines were carried out through short and long duration tests. The full duration test performed for the durability verification of the engines revealed a few of items to be improved. Synthetically, encouraging data of adding power to engine development were obtained from the test results. New engines based on these results will be manufactured and consistently verified through hot-firing tests.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.171-176
• /
• 2016

In this paper, the integration of the firing test stages at the acceptance test of the propelling charge has been studied using statistical analysis on the basis of the test data of K676 and K677 propelling charge for K9 self propelled howitzer. Acceptance test of K676 / K677 propelling charge consists of 3 stages and each stage is charge assessment test, charge uniformity test and charge proving ground test. Many of rounds are fired and much money is spent to prove the charge performance at each stage. The result of t-test shows that there is no difference between charge uniformity and charge proving ground test stage of K676 and K677 propelling charge.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.296-303
• /
• 2012

The captive model test of submerged body using CPMC(Computerized Planar Motion Carriage) was carried out at the Ocean Basin of KORDI/MOERI. The target model is a submarine with general hullform. The forces and moments acting on the submerged body were measured by 6-axis waterproof gage. The oblique motion test and turning test were carried out in horizontal and vertical planes of the model. Maneuvering coefficients and derivatives were obtained from the test results. The stability indices in horizontal and vertical planes were obtained by using maneuvering derivatives. In this paper the introduction of test equipment and test results are presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1088-1093
• /
• 2010

The Smart bi-directional pile load test with variable end plate overcomes the shortcoming of the Osterberg cell test. It is possible that the ultimate bearing capacity of piles can be known by using two different end plates. The first step is to measure end bearing capacity with smaller end plate and the second step is similar to the conventional O-cell test. In this study, model test was performed to evaluate the smart bi-directional pile load test in sand. Vertical displacement of the model pile were messured at the axial loading condition.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.11
• /
• pp.3086-3096
• /
• 1999

To declare conformance of multi-protocol Implementation Under Test(IUT), every layer of the multi-protocol IUT should be tested. According to ISO9646, single-layer test method is applied to testing the highest layer of multi-protocol IUT and single-layer embedded test method is used for the layers by layer all the protocols in a multi-protocol IUT. This paper proposes a new method for testing a multi-protocol IUT. The proposed test method assumes that a multi-protocol IUT is under test and that the interfaces between the layers cannot be controlled or observed by the tester. We apply the proposed test method to TCP/IP and compare the application results with those of the existing test turns out that the proposed test method significantly reduces the number of test cases as well as the number of test events while providing the same test coverage. In addition, the proposed test method shows the capability to locate the layer that is source of failure in testing multi-protocol IUTs.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.61 no.3
• /
• pp.43-53
• /
• 2019

It is well-known fact that the stone-mastic asphalt (SMA) mixture has shown superior rut resistance, compared with the dense-graded asphalt (DGA) mixture in highway pavements. However, the SMA is measured to be inferior to DGA mixes when tested by well-known high-temperature test methods, such as the wheel tracking (WT), asphalt pavement analyzer, the Marshall Stability and Kim Test. Therefore, this study examined the reasons why it was measured to be inferior, and devised a potential procedure by which the superiority of SMA could be measured at $60^{\circ}C$. The strength against deformation ($S_D$), which was known to show very high correlation with WT results for DGA mixes, was measured by the Kim Test on the specimen confined in the compacted mold. In standard Kim Test, which used the specimen without confinement, the DGA was measured to show higher $S_D$ than the SMA. But by confining specimen, it was found that the $S_D$ of SMA was measured to be higher than that of DGA. Therefore, the confined static test protocol devised in this study was found to be feasible for evaluating rut resistance of SMA mix.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.4
• /
• pp.15-23
• /
• 2006

In this paper, full-scale airframe static test of 4-seater canard airplane(the Firefly) was explained. From the results of the structural analysis, 5 design limit loads test conditions and 11 design ultimate loads test conditions were selected. Test loads analysis was performed and test fixtures and load control system(LCS) were prepared to realize the test loads. To protect the test article during the test, the overload protection system was prepared. Strain and deflection values were acquired through the data acquisition system(DAS) to verify the structural analysis results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.718-725
• /
• 2016

In this study, the plastic flow curve of commercially pure titanium sheet (CP Ti) actively used in the plate heat exchanger etc., was evaluated. The plastic flow curve known as hardening curve is a key factor needed in conducting finite element analyses (FEA) for the forming process of a sheet material. A hydraulic bulge test was performed on the CP Ti sheet and the strain in this test was measured using the DIC method and ARAMIS system. The measured true stress-true strain curve from the hydraulic bulge test (HBT) was compared with that from the tensile test. The measured true stress-true strain curve from the hydraulic bulge test showed stable plastic flow curve over the strain range of 0.7 which cannot be obtained in the case of the uniaxial tensile test. The measured true stress-true strain curve from the hydraulic bulge test can be fitted well by the hardening equation known as the Kim-Tuan model.

• Journal of applied mathematics & informatics
• /
• v.5 no.1
• /
• pp.263-268
• /
• 1998

This paper proposes the two-sample comparison us-ing sign test based on ranked-set sample(RSS). We investigate the asymptotic properties of the proposed test statistic and compare the asymptotic relative efficiencies of the proposed test statistic with re-spect to Mann-Whitney-Wilcoxon test statistic based on RSS and Mann-Whitney-Wilcoxon test statistic based on the simple random sample(SRS).

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.19-25
• /
• 2009

This paper includes test results of 30tonf-level TP+GG startup simulation cold flow test using liquid oxygen and kerosene. Test objectives, coupled test plant configuration, test condition, test procedure of performed tests, and test results are presented.