• 센서학회지
• /
• 제24권4호
• /
• pp.219-223
• /
• 2015

Indium free consisting of three alternating layers GTO/Ag/GTO has been fabricated by radio-frequency (RF) sputtering for the applications as transparent conducting electrodes and the structural, electrical and optical properties of the gallium tin oxide (GTO) films were carefully studied. The gallium tin oxide thin films deposited at room temperature are found to have an amorphous structure. Hall Effect measurements show a strong influence on the conductivity type where it changed from n-type to p-type at $700^{\circ}C$. GTO/Ag/GTO multilayer structured electrode with a few nm of Ag layer embedded is fabricated and show the optical transmittance of 86.48% in the visible range (${\lambda}$ = 380~770 nm) and quite low electrical resistivity of ${\sim}10^{-5}{\Omega}cm$. The resultant power conversion efficiency of 2.60% of the multilayer based OPV (GAG) is lower than that of the reference commercial ITO. GTO/Ag/GTO multilayer is a promising transparent conducting electrode material due to its low resistivity, high transmittance, low temperature deposition and low cost components.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1459-1461
• /
• 1996

The optical and electrical properties of High Power AlGaAs/AlGaAs Infrared LED with DDH( Double power Double Hetero Junction) structure are investigated. The high power LED is recently studied in order to apply to high speed communication devices. The power out of AlGaAs/AlGaAs with DDH structure is 13.0[mW], the forward voltage is 1.45[V], and the average decrease rate of power out is about 5[%] after aging test. The optical and electrical properties of DDH structure LED are superior than that of SH structured LED. The DDH structured LED is suitable to the high speed communication devices.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.497-500
• /
• 2001

Due to their better photosensitivity in X-ray, the amorphous selenium based photoreceptor is widely used on the X-ray conversion materials. It was possible to control the charge carrier transport of amorphous selenium by suitably alloying a-Se with other elements(e.g. As, Cl). The charge transport properties of amorphous Selenium is decided on hole which is induced from metal to selenium in metal-selenium junction and which is transferred in a-Se bulk. This phenomenon is resulted of changing electric field owing to increasing of space charge by deep trap of a-Se bulk. In this paper, We dopped the chlorine to compensate deep hole trap and deposited blocking layer using dielectric material to prevent from increasing space charge for injection charge between metal electrode and a-Se layer. We compared space charge and the decreasing of trap density through measuring dark and photo current. 缀Ѐ㘰〻ሀ䝥湥牡氠瑥捨湯汯杹

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.115-115
• /
• 2011

Nano hybrid superlattices consisting of organic and inorganic components have great potential for creation of new types of functional material by utilizing the wide variety of properties which differ from their constituents. They provide the opportunity for developing new materials with new useful properties. Herein, we fabricated new type of organic-inorganic nano hybrid superlattice thin films by a sequential, self-limiting surface chemistry process known as molecular layer depostion (MLD) combined with atomic layer deposition (ALD). An organic layer was formed at $150^{\circ}C$ using MLD with repeated sequintial adsorption of Hydroquinone and Titanium tetrachloride. A $TiO_2$ inorganic nanolayer was deposited at the same temperature using ALD with alternating surface-saturating reactions of Titanium tetrachloride and water. Using UV-Vis spectroscopy, we confirmed visible light absorption by LMCT. And FTIR spectroscopy and XPS were employed to determine the chemical composition. Ellipsometry and TEM analysis were also used to confirm linear growth of the film versus number of MLD cycles at all same temperature. In addition, p-n junction diodes domonstrated in this study suggest that the film can be suitable for n-type semiconductors.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.60-60
• /
• 2011

Giant magnetoresistance (GMR), tunneling magnetoresistance (TMR), and magnetic random-access memory (MRAM) are currently active research areas in spintronics. The high magnetoresistance and the high spin polarization (P) of electrons in the ferromagnetic electrodes of tunnel junction or intermediate layers are required. Magnetite, Fe3O4, is predicted to possess as half-metallic nature, P ~ 100% spin polarization, and has a high Curie temperature (TC~850 K). Experiments demonstrated that the P~($80{\pm}5$)%, ~($60{\pm}5$)%, and ~40-55% for epitaxial (111), (110) and (001)-oriented Fe3O4 thin films, respectively. Epitaxial Fe3O4 films may enable us to investigate the effects of half metals on the spin transport without grain-boundary scattering.In addition, it has been reported that the Verwey transition (TV, a first order metal-insulator transition) of 120 K in bulk Fe3O4 is strongly affected by many parameters such as stoichiometry and stress, etc. Here we report that the growth modes, magnetism and transport properties of Fe3O4 thin films were strongly dependent on the oxygen pressure during film growth. The average roughness decreases from 1.021 to 0.263 nm for the oxygen pressure increase from $2.3{\times}10-7$ to $8.2{\times}10^{-6}$ Torr, respectively. The 120 K Verwey transition in Fe3O4 was disappeared for the sample grown under high oxygen pressure.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.253-253
• /
• 2011

ZnTe semiconductor is very attractive a material for optoelectronic devices in the visible green spectral region because of it has direct bandgap of 2.26 eV. The prototypes of ZnTe light emitting diodes (LEDs) have been reported [1], showing that their green emission peak closely matches the most sensitive region of the human eye. The optoelectronic properties of ZnTe:O film allow to expect a large optical gain in the intermediate emission band, which emission band lies about 0.4-0.6 eV below the conduction band of ZnTe [2]. So, the ZnTe system is useful for the production of high-efficiency multi-junction solar cells [2,3]. In this work, the ZnTe:O thin films were deposited on Al2O3 substrates by using the radio frequency magnetron sputtering system. Three sets of samples were prepared using argon and oxygen as the sputtering gas. The deposition chamber was pre-pumped down to a base pressure of 10-7 Torr before introducing gas. The deposition pressure was fixed at 10-3 Torr throughout this work. During the ZnTe deposition, the substrate temperature was 300 oC. The optical properties were also investigated by using the ultraviolte-visible (UV-Vis) spectrophotometer.

• Transactions on Electrical and Electronic Materials
• /
• 제6권3호
• /
• pp.124-127
• /
• 2005

It has been a long time since organic solar cells were expected as a low-cost energy-conversion device. Although practical use of them has not been achieved, technological progress continues. Morphology of the materials, organic/inorganic interface, metal cathodes, molecular packing and structural properties of the donor and acceptor layers are essential for photovoltaic response. We have fabricated solar cell devices based on zinc-phthalocyanine(ZnPc) as donor(D) and fullerene$(C_60)$ as electron acceptor(A) with doped charge transport layers, and BCP and $Alq_3$ as an exciton blocking layer(EBL). We have measured the photovoltaic characteristics of the solar cell devices using the Xe lamp as a light source. We were use of $Alq_3$ layer leads to external power conversion efficiency was $2.65\%$ at illumination intensity $100\;mW/cm^2$. Also we confirmed the optimum thickness ratio of the DA hetero-junction is about 1:2.

• 한국재료학회지
• /
• 제30권2호
• /
• pp.99-104
• /
• 2020

Recent discoveries of ferroelectric properties in ultrathin doped hafnium oxide (HfO₂) have led to the expectation that HfO₂ could overcome the shortcomings of perovskite materials and be applied to electron devices such as Fe-Random access memory (RAM), ferroelectric tunnel junction (FTJ) and negative capacitance field effect transistor (NC-FET) device. As research on hafnium oxide ferroelectrics accelerates, several models to analyze the polarization switching characteristics of hafnium oxide ferroelectrics have been proposed from the domain or energy point of view. However, there is still a lack of in-depth consideration of models that can fully express the polarization switching properties of ferroelectrics. In this paper, a Zr-doped HfO₂ thin film based metal-ferroelectric-metal (MFM) capacitor was implemented and the polarization switching dynamics, along with the ferroelectric characteristics, of the device were analyzed. In addition, a study was conducted to propose an applicable model of HfO₂-based MFM capacitors by applying various ferroelectric switching characteristics models.

• 한국전기전자재료학회논문지
• /
• 제28권4호
• /
• pp.213-217
• /
• 2015

Device model parameters are very important for accurate estimation of electrical performances in devices, integrated circuits and their systems. There are a large number of methods for extraction of model parameters in power MOSFETs. For high efficiency, design is important considerations of a power MOSFET with high-voltage applications in consumer electronics. Meanwhile, it was proposed that the efficiency of a MOSFET can be enhanced by conducting JFET region double implant to reduce the On-resistance of the transistor. This paper reports the effects of JFET region double implant on the electrical properties and the decreasing On-resistance of the MOSFET. Experimental results show that the 1st JFET region implant diffuse can enhance the On-resistance by decreasing the ion concentration due to the surface and reduce the On-resistance by implanting the 2nd Phosphorus to the surface JFET region.

• 한국전기전자재료학회논문지
• /
• 제22권2호
• /
• pp.128-131
• /
• 2009

Silicon carbide (SiC) has attracted significant attention for high frequency, high temperature and high power devices due to its superior properties such as the large band gap, high breakdown electric field, high saturation velocity and high thermal conductivity. We performed Al ion implantation processes on n-type 4H-SiC substrate using a SILVACO ATHENA numerical simulator. The ion implantation model used Monte-Carlo method. We simulated the effect of channeling by Al implantation in both 0 off-axis and 8 off-axis n-type 4H-SiC substrate. We have investigated the effect of varying the implantation energies and the corresponding doses on the distribution of Al in 4H-SiC. The controlled implantation energies were 40, 60, 80, 100 and 120 keV and the implantation doses varied from $2{\times}10^{14}$ to $1{\times}10^{15}\;cm^{-2}$. The Al ion distribution was deeper with increasing implantation energy, whereas the doping level increased with increasing dose. The effect of post-implantation annealing on the electrical properties of Al-implanted p-n junction diode were also investigated.