• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.99-104
• /
• 2015

The requirement for success of via filling is its ability to fill via holes completely without producing voids or seams. Defect free via filling was obtained by optimizing plating conditions such as current mode, current density and additives. However, byproducts stemming from the breakdown of these organic additives reduce the lifetime of the devices and plating solutions. In this study, the relationship between JGB and current density on the copper via filling was investigated without the addition of other additives to minimize the contamination of copper via. AR 4 with $15{\mu}m$ diameter via were used for this study. The pulse current was used for the electroplating of copper and the current densities were varied from 10 to $20mA/cm^2$ and the concentrations of JGB were varied from 0 to 25 ppm. The map for the JGB concentration and current density was developed. And the optimum conditions for the AR 4 via filling with $15{\mu}m$ diameter were obtained.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.139-139
• /
• 2016

반도체 다마신배선용 도금용 구리도금첨가제는 대표적으로 accelerator, suppressor 및 leveler 첨가제를 사용하여 다마신 패턴을 채우고 평탄화를 시킬 수 있다. Si 반도체 공정기술에 기반한 정확한 구조분석을 통해 각각의 첨가제의 기능이 비교적 체계적으로 연구되었으며, 최근에는 유속영향을 많이 받는 것으로 알려진 leveler 첨가제에 대한 연구가 활발히 진행되고 있다. 본 연구는 대표적 leveler 첨가제의 하나인 Janus Green B(JGB, $C_{30}H_{31}ClN_6$)를 0 ~ 1 mM을 첨가하여 Si 기판위에 증착된 Cu 씨드층 상의 도금후 표면상태 및 불순물의 농도를 분석하고, 이 박막층들의 결정립 성장 경향성을 electron backscattered diffraction(EBSD) 분석을 통해 진행하였다. C, H, N 등의 불순물이 JGB 농도와 선형적 관계를 가지고 증가하는 것을 알 수 있었으며, S와 O의 불순물도 JGB 농도 증가에 따라 증가하는 것을 알 수 있었다. 또한 0.1 mM 첨가한 경우에 60% 정도 결정립 성장이 진행된 것을 알 수 있었으며, 0.2 mM을 넣은 경우에는 결정립 성장이 일어나지 않은 것을 알 수 있었다. 흥미로운 점은 4 point probe를 통한 면저항 측정을 통해 EBSD를 통한 결정립성장이 관찰되지 않은 0.2 mM JGB를 첨가한 경우에 대해서도 면저항의 감소가 관찰되며, 오히려 JGB 농도가 높을수록 이러한 면저항의 감소가 빠르게 시작되는 것을 관찰할 수 있었다. 이는 JGB 농도 증가에 따라 박막층의 불순물의 농도가 증가하고 막내에 존재하는 불순물의 농도가 증가하면 내부응력장이 커짐으로 인해 더욱 빠른 속도로 불순물의 재배치가 일어난 것으로 보인다. 이러한 불순물이 결정립계면에 편석되는 경우에 pinning을 통해 결정립계면의 이동을 저하시킬 수 있으므로 결정립의 성장 억제가 가능해진 것으로 판단된다.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.37-42
• /
• 2007

Copper deposition studies have been actively studied since interests on 3D SiP were increased. The defects inside via can be easily formed due to the current density differences on entrance, bottom and wall of via. So far many different additives and current types were discussed and optimized to obtain void-free copper via filling. In this research acid cupric sulfate plating bath containing additives such as PEG, SPS, JGB, PEI and wave current applied electroplating were examined. The size and shape of grain were influenced by the types of organic additives. The cross section of specimen were analyzed by FESEM. When PEI was added, the denser copper deposits were obtained. Electroplaing time was reduced when 2 step via filling was employed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.327-328
• /
• 2015

본 연구에서는 전기도금법을 이용하여 수지상(Dendrite) 구리 분말을 제조할 때 첨가제 유무를 비교하였다. 인가전위, 첨가제의 종류(JGB, PEG) 및 농도에 따른 수지상의 형상적인 특성이 비교되었으며, 겉보기 밀도와 비표면적(BET)이 측정되었다. 형상적 특성은 수지상의 2차 가지와 추축의 두께 비(ratio)로 비교한 결과 JGB 첨가(10ppm) 도금욕에서 30.67로 가장 큰값을 가지며, 겉보기 밀도는 JGB 첨가(80ppm)에서 $1.115g/cm^3fh$ 가장 낮은값을 보였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.167.2-167.2
• /
• 2017

수지상 구리분말은 하나의 상(statue)이 복수의 접점(contact point)를 제공하며 표면적이 넓은 구조적인 특징으로 인해 발열기판 전도성 페이스트 등 다양한 전기 전가 분야에 활용되어왔다. 때문에 본 연구에서는 전해도금방법으로 수지상 구리분말이 형성될 때 첨가제가 수지상의 형상에 어떠한 영향을 미치는지 분석하였다. 첨가제는 PEG, JGB를 사용하여 농도별로 실험을 진행하였다. SEM 이미지 분석결과 첨가제가 추가함에 따라 수지상이 미세해지며 첨가제의 농도가 증가함에 따라 DAS(dendrite arm spacing)값이 감소하여 표면적이 증가하였다. BET 비표면적 분석결과 PEG($1.882m^2/g$)보다 JGB($2.119m^2/g$)에서 표면적을 넓히는 효과가 뛰어났다.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.4
• /
• pp.153-157
• /
• 2013

The defect like the void or seam is frequently generated in the PCB (Printed Circuit Board) Via-Filling plating inside via hole. The organic additives including the accelerating agent, inhibitor, leveler, and etc. are needed for the copper Via-Filling plating without this defect for the plating bath. However, the decomposition of the organic additive reduces the lifetime of the plating bath during the plating process, or it becomes the factor reducing the reliability of the Via-Filling. In this paper, the interaction of each organic additives and the decomposition of additive were discussed. As to the accelerating agent, the bis (3-sulfopropyl) disulfide (SPS) and leveler the Janus Green B (JGB) and inhibitor used the polyethlylene glycol 8000 (PEG). The research on the interaction of the organic additives and decomposition implemented in the galvanostat method. The additive decomposition time was confirmed in the plating process from 0 Ah/l (AmpereHour/ liter) to 100 Ah/l with the potential change.

• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.335-341
• /
• 2012

Recently, the demand for the miniaturization of printed circuit boards has been increasing, as electronic devices have been sharply downsized. Conventional multi-layered PCBs are limited in terms their use with higher packaging densities. Therefore, a build-up process has been adopted as a new multi-layered PCB manufacturing process. In this process, via-holes are used to connect each conductive layer. After the connection of the interlayers created by electro copper plating, the via-holes are filled with a conductive paste. In this study, a desmear treatment, electroless plating and electroplating were carried out to investigate the optimum processing conditions for Cu via filling on a PCB. The desmear treatment involved swelling, etching, reduction, and an acid dip. A seed layer was formed on the via surface by electroless Cu plating. For Cu via filling, the electroplating of Cu from an acid sulfate bath containing typical additives such as PEG(polyethylene glycol), chloride ions, bis-(3-sodiumsulfopropyl disulfide) (SPS), and Janus Green B(JGB) was carried out. The desmear treatment clearly removes laser drilling residue and improves the surface roughness, which is necessary to ensure good adhesion of the Cu. A homogeneous and thick Cu seed layer was deposited on the samples after the desmear treatment. The 2,2'-Dipyridyl additive significantly improves the seed layer quality. SPS, PEG, and JGB additives are necessary to ensure defect-free bottom-up super filling.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.2
• /
• pp.141-147
• /
• 2015

Using laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), we evaluated the reliability of trace element abundance data measured from the silicate rock references of JR-3, JG-3, JGb-1 and JB-1b using glass discs made by alkali fusion. For 28 elements including rare earth elements, relative standard deviations (RSD) are better than 7% in case when the concentrations of the elements in the rock samples are greater than 10 ppm. However, RSD shows somewhat increased values for the concentrations less than 10 ppm, but never exceeds 25%. Compared with previously reported averages of the compiled abundance data, our data display satisfactory results for the most cases with differences less than 10%. We suggest that LA-ICP-MS analysis using fused glass beads is a reliable, precise and time-saving method of trace element analysis for the silicate rocks spanning from mafic to felsic compositions.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.67-72
• /
• 2012

In recent days, the wire width of IC is narrowed and the degree of integration of IC is increased to obtain the higher capacity of the devices in electronic industry. And then the surface quality of FCCL(Flexible Copper Clad Laminate) became increasingly important. Surface defects on FCCL are bump, scratch, dent and so on. In particular, bumps cause low reliability of the products. Even though there are bumps on the surface, if leveling characteristic of plating solution is good, it does not develop significant bump. In this study, the leveling characteristics of additives are investigated. The objective of study is to improve the leveling characteristic and reduce the surface step through additives and plating conditions. The additives in the electrodeposition bath are critical to obtain flat surface and free of defects. In order to form flat copper surface, accelerator, suppressor and leveler are added to the stock solution. The reason for the addition of leveler is planarization surface and inhibition of the formation of micro-bump. Levelers (SO(Safranin O), MV(Methylene Violet), AB(Alcian Blue), JGB(Janus Green B), DB(Diazine Black) and PVP(Polyvinyl Pyrrolidone) are used in copper plating solution to enhance the morphology of electroplated copper. In this study, the nucleation and growth behavior of copper with variation of additives are studied. The leveling characteristics are analyzed on artificially fabricated Ni bumps.

• Corrosion Science and Technology
• /
• v.10 no.4
• /
• pp.143-150
• /
• 2011

Copper electroplating has been applied to various fields such as decorative plating and through-hole plating. Technical realization of high strength copper preplating for wear-resistant tools and molds in addition to these applications is the aim of this work. Brighters and levelers, such as MPSA, Gelatin, Thiourea, PEG and JGB, were added in copper sulfate electrolyte, and the effects of these organic additives on the hardness were evaluated. All additives in this work were effective in increasing the hardness of copper electrodeposits. Thiourea increased the hardness up to 350 VHN, and was the most effective accelarator in sulfate electrolyte. It was shown from the X-ray diffraction analysis that preferred orientation changed from (200) to (111) with increasing concentration of organic additives. Crystallite size decreased with increasing concentration of additive. Hardness was increased with decreasing crystallite size, and this result is consistent with Hall-Petch relationship, and it was apparent that the hardening of copper electrodeposits results from the grain refining effect.