• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.36-38
• /
• 2001

A basic structure of 2500V-4500V reverse-conducting GCT (RC-GCT) is given in this paper. The punch-through type (PT) is adopted for narrow N-base with high resistivity so that the fast turn-off and low on-state voltage can be achieved. The photo mask design was made upon the both turn-off performance and solution of separation between GCT and integrated freewheeling diode (FWD) part. The turn-on and turn-off characteristics for reserve-conducting gate commutated thyristors (RC-GCTs) were investigated by ISE simulation. Additionally, the local carrier lifetime control by proton irradiation was adopted so as not only to obtain the reduction of turn-off losses of GCT but also to reach a soft reverse recovering characteristics of FWD

• Journal of Powder Materials
• /
• v.20 no.5
• /
• pp.376-381
• /
• 2013

Spherical Ti-6Al-4V powders in the size range of 250 and 300 ${\mu}m$ were uniformly doped with nano-sized hydroxyapatite (HAp) powders by Spex milling process. A single pulse of 0.75-2.0 kJ/0.7 g of the Ti-6Al-4V powders doped with HAp from 300 mF capacitor was applied to produce fully porous and porous-surfaced Ti-6Al-4V implant compact by electro-discharge-sintering (EDS). The solid core was automatically formed in the center of the compact after discharge and porous layer consisted of particles connected in three dimensions by necks. The solid core increased with an increase in input energy. The compressive yield strength was in a range of 41 to 215 MPa and significantly depended on input energy. X-ray photoelectron spectroscopy and energy dispersive x-ray spectrometer were used to investigate the surface characteristics of the Ti-6Al-4V compact. Ti and O were the main constituents, with smaller amount of Ca and P. It was thus concluded that the porous-surfaced Ti-6Al-4V implant compacts doped with HAp can be efficiently produced by manipulating the milling and electro-discharge-sintering processes.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.392-395
• /
• 2003

The study of electric field analyses has been conducted on two kinds of bushings for 17.5kV $SF_6$ gas insulated recloser. In this paper, two model bushings and input conditions for the analyses are described in detail. The results of the electric field analyses are presented and compared with to find out the better design in two bushings. Finally some suggestions are given for improving the insulation characteristics of the bushings.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.1
• /
• pp.67.2-67.2
• /
• 2019

We present the results of KVN and ALMA observations toward WX Psc (IRC+10011) which is a long-period variable OH/IR star. The SiO masers of v=1 and v=2, J=5-4, and the SiO thermal emission of v=0, J=5-4 were observed together with H2O v2=1 (232.6 GHz) and continuum emission at ALMA Band 6 in October 2017 (Cycle 5). This observation aims to investigate the physical association between the inner and outer parts of the circumstellar envelope (CSE) swept by the stellar winds, which is very crucial to understand the asymmetric outward motions developed during the evolutionary phases from the asymptotic giant branch (AGB) stars to the planetary nebulae (PNe). The strong SiO maser features and thermal emissions are detected together with the continuum emission in ALMA observation, which imply the elongated morphology of the CSE of WX Psc. While the spatial resolution of about 20 mas in ALMA observation cannot clearly resolve the detailed characteristics of the inner part of the CSE, the Korean VLBI Network (KVN) observations show the spatial distributions of the v=1 J=1-0, J=2-1, J=3-2 SiO masers emitted from the inner regions of CSE, which are the complementary to the ALMA results. Therefore, we expect these results reveal how the bipolar features of the 22 GHz H2O maser are connected to the innermost region of CSE through the dust condensation region, which is closely related to the enormous mass ejection of the evolved stars.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.63-63
• /
• 2009

In this work, we demonstrate 800V 4H-SiC power DMOSFETs with several structural alterations to observe static DC characteristics, such as a threshold voltage ($V_{TH}$) and a figure of merit ($V_B^2/R_{SP,ON}$). To optimize the static DC characteristics, we consider four design parameters; (a) the doping concentration ($N_{CSL}$) of current spreading layer (CSL) beneath the p-base region, (b) the thickness of p-base ($t_{BASE}$), (c) the doping concentration ($N_J$) and width ($W_J$) of a JFET region, (d) the doping concentration ($N_{EPI}$) and thickness ($t_{EPI}$) of epi-layer. Design parameters are optimized using 2D numerical simulations and the 4H-SiC DMOSFET structure results in high figure of merit ($V_B^2/R_{SP,ON}$>~$340MW/cm^2$) for a power MOSFET in $V_B{\sim}1200V$ range.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.52-59
• /
• 2007

We investigated the effects of the addition of Mn and $AB_5$ type alloy on the electrochemical characteristics of Ti-Cr-V BCC type alloys as anode materials for Ni-MH battery. The activation behavior and discharge capacity of the BCC type alloys were significantly improved by ball-milling with the $LmNi_{4.1}Al_{0.25}Mn_{0.3}Co_{0.65}$ alloy, because the $AB_5$ type alloy acted as hydrogen path on the surface of the BCC type alloy. Among the Mn substituted alloys($Mn=0.03%{\sim}0.08%$), the $Ti_{0.32}Cr_{0.38}Mn_{0.05}V_{0.25}$ alloy ball-milled with $AB_5$ type alloy exhibited the greatest discharge capacity of $336\;mAh{\cdot}g^{-1}$. In addition, Mn substituted alloys exhibited the lower plateau pressure in P-C- T curve, the better hydrogen storage capacity and faster surface activation compared with the alloy without Mn.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1332-1336
• /
• 1995

In this paper, the procedures and the results of design and manufacturing technologies, mechanical operating tests, insulation tests and short-circuit tests for 800kV 40kA model GCB are presented. The problems to be solved and the countermeasures for the problems are also proposed to improve the performances the model GCB.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.322-324
• /
• 1999

This paper presents the methodology of measuring the 22.9[kV] bus load characteristics for verifying the bus load model developed with equivalent load aggregation of load components, and the analysis of 22.9[kV] load data.

• Transactions of Materials Processing
• /
• v.27 no.3
• /
• pp.177-183
• /
• 2018

The influence of electric current on the springback characteristics of AZX311 magnesium alloy and martensitic steel after V-bending test is investigated. Various pulsed electric currents are applied into the specimens followed by a V-bending test, and the changes in the springback angle are measured. In order to evaluate not only the thermal effect but also the athermal effect of electric current on the springback angle, the temperature rises resulting from the applied electric current are measured for all test conditions. As a result, it was found that the springback is significantly decreased as the current density increases. As for the martensitic steel, since the dislocation recovery immoderately occurs at a high electric current density condition of $80A/mm^2$, the optimal current density condition should be required.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.701-706
• /
• 2003

Fuel cell is remarkable for one of the clean energy recently. But in the fuel cell case, it has characteristics with low voltage and high current. Therefore, for using domestic power, it should be changed to the power source with commercial voltage and frequency. In this paper fuel cell simulator having electrical characteristics is designed and constructed instead of fuel cell stack. Voltage generated from fuel cell is from 39V to 72V dc and should be boosted to 400v do for home appliances. A stand alone system including the inverter and DC/DC converter for the fuel cell is then proposed. Experimental result is used to support the analysis.