• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.8
• /
• pp.756-760
• /
• 2010

In this paper, a new method to recognize various motions of fighting with an aid of HMM is proposed. There are four kinds of fighting motion such as hook, jab, uppercut, and straight as the fighting motion. The motion graph is generalized to define each motion in motion data and the new 3D-chain code is used to convert motion data to motion graphs. The recognition experiment has been performed with HMM algorithm on motion graphs. The motion data is captured by a motion capture system developed in this study and by five actors. Experimental results are given with relatively high recognition rate of at least 85%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.98-106
• /
• 1998

In this study a control law and performance potential of semi-active suspensions for a tractor/semi-trailer have been investigated. The control law for airbag semi-active suspensions modeled in this study is developed using feedback linearization and Linear Quadratic (LQ) optimal control method. Inherent nonlinearity of the airbag suspensions has been considered in the control law development. It has been shown that the proposed semi-active control law provides better performance than that of well known sky-hook damping control strategy.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.11
• /
• pp.1662-1669
• /
• 2007

The high mobility group AT-hook1 (HMGA1) proteins are known to be related to the regulation of gene transcription, replication and promotion of metastatic progression in cancer cells. The loss of expression by disrupting the HMGA1 gene affects insulin signaling and causes diabetes in the mouse. Previously identified single nucleotide polymorphism (SNP) of HMGA1 was significantly associated with fat deposition traits in the pig. In this study, we identified 3,935 bp nucleotide sequences from exon 5 to exon 8 of the bovine HMGA1 gene and its mRNA expression was observed by quantitative real-time PCR. Six single nucleotide polymorphisms in the bovine HMGA1 gene were detected and the allele frequencies of these SNPs were investigated using the PCR-RFLP method in nine cattle breeds including Limousin, Simmental, Brown Swiss, Hereford, Angus, Charolais, Hanwoo, Brahman and Red Chittagong cattle. The map location showed that the bovine HMGA1 gene was also closely located with a previously identified meat quality QTL region indicating this gene is the most likely positional candidate for meat quality traits in cattle.

• Journal of agricultural medicine and community health
• /
• v.4 no.1
• /
• pp.81-89
• /
• 1979

This study was undertaken to evaluate the present status of intestinal helminthic infection in rural areas of Korea from Dec. 1976 to Feb. 1979.The 4,311 stool specimens collected from 4 mountainous areas, 2 plain areas and 4 ri ver basins were examined. The methods employed were Kato's cellophane thick smear technique and brine fletation technique. The results are as follows. 1. The positive rate of intestinal helminch of any kind was 73.4%. It was 82.9% in river basins, 70. 2% in plain areas and 70. 4% in mountainous areas. 2. The positive rates of intestinal helmint.h were; Ascaris lumbricoides 42.5%, Trichocephalus trichiurus 51.4%, Hookworm 4.2%, Clonorchis sinensis 4.0%, Meta-gonimus yokogawai 5.7%, Hymenolepis nana 1.3%, Taenia species 1.0%, and Trichostrongyllus orientalis 1.2% respectively. 3. Sexual distribution of heiminthic infections showed higher rate in female than that of male except C. sinensis, H. nana, Taenia species, and. M. yokogawai. 4.Infection rates of T. trichiurus, Hook-worm and C. sinensis increased with age, but conversely H. nana were more prominent in younger age. 5. No geographical differen=e was noticed except that, M. yokogawai (20.9%), C sinensis (14.2%) in river basins ancl Taenia species (2.3%, by applying only stool examination) in mountainous areas were higher than the other 2 areas.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.9
• /
• pp.1229-1238
• /
• 2016

This study was conducted to determine the relationships of five intragenic single nucleotide polymorphism (SNP) markers (protein kinase adenosine monophosphate-activated ${\gamma}3$ subunit [PRKAG3], fatty acid synthase [FASN], calpastatin [CAST], high mobility group AT-hook 1 [HMGA1], and melanocortin-4 receptor [MC4R]) and meat quality traits of Duroc breeding stocks in Korea. A total of 200 purebred Duroc gilts from 8 sires and 40 dams at 4 pig breeding farms from 2010 to 2011 reaching market weight (110 kg) were slaughtered and their carcasses were chilled overnight. Longissimus dorsi muscles were removed from the carcass after 24 h of slaughter and used to determine pork properties including carcass weight, backfat thickness, moisture, intramuscular fat, $pH_{24h}$, shear force, redness, texture, and fatty acid composition. The PRKAG3, FASN, CAST, and MC4R gene SNPs were significantly associated with the meat quality traits (p<0.003). The meats of PRKAG3 (A 0.024/G 0.976) AA genotype had higher pH, redness and texture than those from PRKAG3 GG genotype. Meats of FASN (C 0.301/A 0.699) AA genotype had higher backfat thickness, texture, stearic acid, oleic acid and polyunsaturated fatty acid than FASN CC genotype. While the carcasses of CAST (A 0.373/G 0.627) AA genotype had thicker backfat, and lower shear force, palmitoleic acid and oleic acid content, they had higher stearic acid content than those from the CAST GG genotype. The MC4R (G 0.208/A 0.792) AA genotype were involved in increasing backfat thickness, carcass weight, moisture and saturated fatty acid content, and decreasing unsaturated fatty acid content in Duroc meat. These results indicated that the five SNP markers tested can be a help to select Duroc breed to improve carcass and meat quality properties in crossbred pigs.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.3
• /
• pp.188-198
• /
• 2005

This study was conducted to survey the catches of vertical bottom longline fisheries in the sea mount of central northern Pacific($30^{\circ}-42^{\circ}N$, $170^{\circ}-175^{\circ}E$), during the period of July 1 to August 25,2004 by commercial fishing vessel. The number of 57 test fishing was carried out in the central northern Pacific during 43 days and the total catches were 21,092.4kg as 19 fish species, CPUE/day and catches/day were 185 baskets and 490.5kg, respectively. Main fish species caught from the experimental fishing were Squalus mitsukurii (66.3%), Coelorhyrchus asperocephaius (11.7%) and Helicolenus avius (9.8%) and, average inside diameter for fish mouth was 4.0cm over. Catch ratio according to each fishing ground was the order of F, D, J, B and C. Catch ratio fur water depth was the order of 450-500m, 350-400m, 300-350m, 400-450m, 1000-1100m and 500-550m and, main species by water depth was Squalus mitsukurii for 300-400m, Etmopterus lucifer for 300-550m, Coelorhyrchus asperocephaius far 1,000m over. Catch ratio according to the kind of hooks was higher at the hook no.6 for Squalus mitsukurii and no. 5 for Etmopterus lucifer and, catch ratio by baits was higher at squid for Squalus mitsukurii, saury and eel for Helicolemus avius and saury for Etmopterus lucifer. Accordingly, it is thought that the extension of fishing hours is needed with the reduction of damage and loss for fishing gears during fishing operation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.3
• /
• pp.290-297
• /
• 2011

The phenology of Campylaephora hypnaeoides J. Agardh and optimal conditions for carpospore release, growth and reproduction were examined in the field and in the laboratory from January to December 2007. In the field population of C. hypnaeoides, approximately 50% of the plants were vegetative during the study period. Additionally, the percentages of carposporophytes and tetrasporophytes were maximal in April (37%) and June (57%), respectively. Maximum growth in plant length, dry weight, and hook number coincided with the tetrasporophyte reproductive peak in the field. In culture, carpospore release, sporeling growth and reproduction were affected by environmental factors such as daylength, temperature, and salinity. The liberation of carpospores was maximum under continuous light and at a combination of $15^{\circ}C$ and $10\;{\mu}mol$ photons $m^{-2}\;s^{-1}$. Maximum growth of tetrasporophyte sporelings occurred at a combination of $20\;{\mu}mol$ photons $m^{-2}\;s^{-1}$ of constant light and $25^{\circ}C$. However, the growth of gametophyte sporelings was maximal under $40\;{\mu}mol$ photons $m^{-2}\;s^{-1}$ of constant light and in a combination of $20^{\circ}C$ and 35 psu. The tetrasporophyte sporelings were grew faster than gametophytes, indicating that gametophyte- and tetrasporophyte-sporelings have different physiological responses to irradiance and temperature. Tetrasporangial branches and cystocarps of C. hypnaeoides were produced from carpospores and tetraspores within 1 month, and they were stimulated at high temperature and irradiance levels. In conclusion, C. hypnaeoides should be seeded using carpospores during early winter (November-December) because cystocarps are easily identified by fishermen, and tetrasporophytes grow faster than gametophytes.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.95-102
• /
• 2018

This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes are well-coordinated to add up the lift capabilities of both cranes without any loss such that virtually a single crane is lifting, maneuvering and unloading. Two main constraints for the dual lifting are as follows: First, two barges of floating cranes should be constrained as a rigid body not to cause a relative motion between two barges and main hooks of the two cranes should be controlled as main hooks of a single crane. In order words, it is necessary to develop the cooperative control of two floating cranes in order to sustain a center of gravity of the module and minimize the tilting angle during the lifting and unloading by the two floating cranes. Two floating cranes are handled as a master-slave system. The master crane is able to gather information about all working conditions and make a decision to control the individual hook speed, which communicates the slave crane by TCP/IP. The developed control system has been embedded in the real floating crane systems and the dual lifting has been demonstrated five times at SHI shipyard in 2015. The moving angles of the lifting module are analyzed and verified to be suitable for hoisting control. It is verified that the dual lifting can be applied for many heavier and wider blocks and modules to shorten the construction time of ships and off-shore platforms.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.261-270
• /
• 2018

In this study, to replace the 'J-slot joint', a joint device between a disposal canister and an emplacement jig in Deep Borehole Disposal process, a novel joint device was designed and tested. The novel joint device was composed of a wedge on top of a disposal canister and a hook box at the end of a winch system. The designed joint device had merits in that it can recombine an emplaced canister freely without the replacement of the joint component. Moreover, it can be applied to various emplacement jigs such as drill pipes, wire-lines, and coiled tubing. To demonstrate the designed joint device, the joint device (${\Phi}110mm$, H 148 mm), a twin canister string (${\Phi}140mm$, H 1,105 mm), and a water tube (${\Phi}150mm$, H 1,500 mm) as a borehole model were manufactured at 1/3 scale. As deployment muds, Na-type bentonite (MX-80) and Ca-type (GJ II) bentonite muds were prepared at solid contents of 7wt% and 28wt%, respectively. The manufactured joint device showed good performance in pure water and viscous muds, with an operation speed of $10m{\cdot}min^{-1}$. It was concluded that the newly developed joint device can be used for the emplacement and retrieval of a deep disposal canister, below 3~5 km, in the future.