• 열처리공학회지
• /
• 제36권5호
• /
• pp.277-284
• /
• 2023

Hardness and damping characteristics of fine discontinuous precipitates (DPs) microstructure generated by low temperature long term isothermal aging were investigated in comparison with those of T6 heat-treated microstructure composed of DPs and continuous precipitates (CPs) in Mg-9%Al alloy. In this study, T6 and fine DPs microstructures were obtained by isothermal aging at 453 K for 24 h and at 413 K for 336 h, respectively, after solution treatment at 693 K for 24 h. The DPs microstructure exhibited higher hardness than the T6 microstructure, which is related to the lower (α + β) interlamellar spacing of the DPs. The DPs microstructure possessed better damping capacity than the T6 microstructure in the strain-amplitude independent region, whereas in the strain-amplitude dependent region, the reverse behavior was observed. The damping tendencies depending on strain-amplitude were discussed based on the microstructural features of the T6 and DPs microstructures.

• 공업화학
• /
• 제23권5호
• /
• pp.456-461
• /
• 2012

본 연구에서는 바이오매스의 에너지 활용성을 확인하기 위하여 실험실 연소로를 이용한 등온 및 비등온 연소특성 연구를 수행하였으며 바이오매스의 시료로는 목재펠렛, 볏짚 및 왕겨를 사용하였다. 바이오매스의 연소시 배출가스의 특성과 분진 및 잔류물을 분석하였으며 그 결과를 RDF의 연소실험 결과와 비교분석하였다. 등온 연소특성 실험으로부터 볏짚이 다른 시료에 비하여 연소속도가 빨라 급격히 산소량이 감소되어 불완전연소율이 증가함을 확인하였으며 목재펠렛의 경우 다른 시료에 비하여 가장 낮은 $NO_{X}$ 배출농도를 나타내었다. 또한 비등온 연소특성 실험으로부터 모든 시료가 $900^{\circ}C$의 연소온도에 도달하기 이전에 연소가 대부분 일어남을 확인할 수 있었으며 $NO_{X}$의 경우 CO가 배출되는 범위와 유사한 온도범위에서 배출되는 반면에 $SO_{2}$의 경우보다 고온에서 배출됨을 확인할 수 있었다.

• 접착 및 계면
• /
• 제14권1호
• /
• pp.21-27
• /
• 2013

셀룰로오스계 레이온섬유 또는 레이온직물은 좁은 온도범위의 안정화공정 동안에 열분해가 매우 빠르게 진행된다. 그러므로 레이온계 탄소섬유를 제조하는데 있어 안정화단계는 매우 중요한 핵심공정이다. 따라서 본 연구에서는 셀룰로오스계 레이온직물의 중량감소, 화학조성, 미세구조 및 texture 변화에 미치는 등온 안정화공정과 초음파세척의 영향을 조사하였다. $200{\sim}240^{\circ}C$ 영역에서 행한 등온 안정화공정의 온도는 레이온직물을 안정화 소요시간, 탄소함량, 산소함량, 셀룰로오스 구조 변화 그리고 직물 texture에 큰 영향을 주었다. 등온 안정화공정 전에 물을 이용한 초음파세척은 레이온직물의 안정화공정 시간을 단축하고, 안정화 후 직물의 탄소함량을 증가하고, 산소함량을 감소시키며, XRD 분석 패턴을 변화시키는데 역할을 하는 것으로 조사되었다. 또한 초음파세척은 등온 안정화공정시 발생하는 레이온직물의 빠른 중량감소 현상을 더디게 하고, 열수축을 감소시켜, 직물의 급격한 물리적 변화의 완화에도 기여하는 것으로 사료된다.

• 한국재료학회지
• /
• 제18권1호
• /
• pp.38-44
• /
• 2008

The micro-structural changes, strength characteristics, and micro-fractural behaviors at the joint interface between a Sn-4.0wt%Ag-0.5wt%Cu solder ball and UBM treated by isothermal aging are reported. From the reflow process for the joint interface, a small amount of intermetallic compound was formed. With an increase in the isothermal aging time, the type and amount of the intermetallic compound changed. The interface without an isothermal treatment showed a ductile fracture. However, with an increase in the aging time, a brittle fracture occurred on the interface due mainly to the increase in the size of the intermetallic compounds and voids. As a result, a drastic degradation in the shear strength was observed. From a microshear test by a scanning electron microscope, the generation of micro-cracks was initiated from the voids at the joint interface. They propagated along the same interface, resulting in coalescence with neighboring cracks into larger cracks. With an increase in the aging time, the generation of the micro-structural cracks was enhanced and the degree of propagation also accelerated.

• 대한기계학회논문집B
• /
• 제21권2호
• /
• pp.224-234
• /
• 1997

It was demonstrated earlier that for laminar, isothermal flow of the lubricant in long journal bearings, inertia has negligible effect on the load carrying capacity and influences only the stability characteristics of the bearing. The question in the present paper is: 'will these conclusions of the isothermal theory remain valid in the presence of significant dissipation, or will lubricant inertia and dissipation interact non-linearly to bring about qualitative changes in bearing performance\ulcorner' The results obtained here assert that the effect of lubricant inertia on load carrying capacity remains negligible, irrespective of the rate of dissipation. The stability of the bearing is, however, affected by lubricant inertia. These results, although obtained here for long bearings with Sommerfeld and Gumbel boundary conditions, are believed to be applicable to practical bearing operations and affirm that bearing load may be calculated from classical, i. e., non-inertial theory.

• 한국표면공학회지
• /
• 제43권6호
• /
• pp.309-314
• /
• 2010

The numerical study for the effect of various factors that affect the temperature distribution of the process glass installed above the large rectangular heater plate was carried out. For the calculation, heat flux, distance between heat source and process glass plate, effect of vacuum condition and convection in a chamber were considered as important factors. The results showed that the temperature gradient on the glass was increased at the natural convection because of the buoyancy force increases due to the heated air. Also, the more heat flux and distance between the heater plate and glass increases, the more increasing the temperature gradient was. In the case of isothermal heating wall, the temperature variation was smaller than the uniform heat flux condition.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제7권
• /
• pp.91-100
• /
• 1999

This paper investigates ventilation characteristics of an environmental chamber simulating an under-floor air conditioning system for isothermal and cooling supply air conditions. The tracer gas sulfur-hexafluoride (SF$F_6$) was injected into a supply duct using step-up and step-down methods. Local mean and room mean ages were calculated from the concentrations measured at internal points and at the exhaust duct. The air change efficiency of the chamber has been found to be greater in cooling conditions than in isothermal conditions. Also the room air change efficiency is not significantly affected but slightly improved by the presence of a supply diffuser.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.243-248
• /
• 2015

We prepared semi-insulating CdTe for radiation detectors by isothermal annealing of single crystals grown by Bridgeman technique in a sealed quartz container filled with Sn vapor. The resistivity of CdTe:Sn samples thus obtained was of order of $10^{10}Ohm{\cdot}cm$ at room temperature with electrons lifetime of $2{\times}10^{-8}$ s, which is appropriate for the applications desired. Analysis of electric transport characteristics depending on temperature, sample thickness and voltage applied revealed the presence of traps with concentration of about $(4-5){\times}10^{12}cm^{-3}$ with the corresponding energy level at 0.8 - 0.9 eV counted from the bottom of conduction band. The conductivity was determined by electron injection from electrodes in space charge limited current mode.

• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.161-169
• /
• 1989

본 연구의 목적의 하나는 기본 유동장과 온도장의 비평행성을 고려함으로써 등온 수직 원통표면 바깥에서의 자연대류 유동의 파형 불안정성에 대한 안정성 문제를 구성하는 것이다. 다음에는 기본 유동양들의 평행성을 고려한 단순화 가정하에 수치해석을 수행하여 안정성 특성에 대한 원통 곡률의 영향을 정성적으로 검토하는 것이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1412-1417
• /
• 2004

Concentric annular heat pipes having the length of 200 mm and the outside diameter of 25.4 mm were manufactured and tested. The inside diameters of the heat pipes were 11.3 mm and 8.1 mm and the material of the container was copper. To compare with thermal performances between the concentric annular heat pipe and a copper block with same shape, start-up and isothermal performance were tested. In the result, the start-up of the concentric annular heat pipe was influenced by the start-up of their heat source. The concentric annular heat pipe reached at steady state faster then the same shape of copper block. The maximum wall temperature difference of the concentric annular heat pipe on whole surface was $4.6^{\circ}C$, and the case of the copper block was $16.5^{\circ}C$.