• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2013-2018
• /
• 2014

According to the manufacturing process of the laminated stator core for an inserted permanent magnet synchronous motor (IPMSM), the iron loss may be different. It is because the mechanical stress imposed to electrical steel sheet is strongly dependent on the manufacturing process. This paper proposes a new iron loss measurement algorithm which utilizes the induced voltage of a search coil and exciting current. The method is effective even when the distribution of magnetic flux density is not uniform along the magnetic flux path as well as uniform. The developed iron loss measurement system is applied to bonded- and embossed-type segmented stator cores of an IPMSM, and the iron losses are quantitatively compared.

• Journal of Electrical Engineering and Technology
• /
• 제8권6호
• /
• pp.1345-1351
• /
• 2013

Variable iron loss as function of current phase angle of Interior Permanent Magnet Synchronous Motor(IPMSM) was calculated through Curve Fitting Method(CFM). Also, a magnetic flux density distribution of iron core according to current phase angle was analyzed, and an iron loss calculation was performed including harmonic distortion. The experiment was performed by production of non-magnetizing model for the separation of mechanical loss, and the iron loss was calculated by the measurement of input using power analyzer and output power using dynamometer. Some error was generated between experimental results and calculation value, but an iron loss diminution according to current phase angle followed a same pattern. So, errors were generated by measurement, vibration, noise, harmonic distortion loss, etc.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.748-753
• /
• 1998

Machine parameters need to measure in advance for vector control and theoretical analysis. Therefore, we present the machine parameter measurement scheme, considering stator iron loss, by the single-phase test at standstill condition. Using this method, the d-q axis inductances and the equivalent iron loss resistance in the voltage equation considering stator iron loss are easily measured. This method is simple and does not need to use complex theory and expensive equipment.

• Journal of Electrical Engineering and Technology
• /
• 제9권4호
• /
• pp.1309-1314
• /
• 2014

The measurement of stator core loss for an induction motor at each manufacturing process is carried out in this paper. Iron loss in the stator core of induction motor changes after each manufacturing process due to the mechanical stress, which can cause the deterioration of the magnetic performances. This paper proposes a new iron loss measuring system of the stator core in an induction motor, which can be applied to the case when the distribution of magnetic flux density is not uniform along the magnetic flux path. In the system, the iron loss is calculated based on the induced voltage of the B-search coil and exciting current.

• Journal of Power Electronics
• /
• 제3권1호
• /
• pp.55-61
• /
• 2003

This paper presents parameter measurement for permanent magnet synchronous motors based on the P-Q circle diagram. Three electrical parameters of permanent magnet synchronous motors, i.e., the equivalent iron loss resistance, armature inductance, and electrical motive force (emf) coefficient are simultaneously measured. The advantages of this method are that it can be implemented under constant excitation and it dispenses with the generating test for the emf coefficient. The proposed method is applied to a 160w permanent magnet synchronous motor, and then the measurement results are analyzed.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.1849-1854
• /
• 2009

This paper describes the design, evaluation and implementation of a compensating algorithm for an iron-cored measurement current transformer (CT) that removes the effects of the hysteresis characteristics of the iron-core. The exciting current resulting from the hysteresis characteristics of the core causes an error of the CT. The proposed algorithm decomposes the exciting current into the core loss current and the magnetizing current and each of them is estimated. The core loss current is calculated from the secondary voltage and the voltage-core loss current curve. The core flux linkage is calculated and then inserted into the flux-magnetizing current curve to estimate the magnetizing current. The exciting current at every sampling interval is obtained by summing the core loss and magnetizing currents and then added to the measured current to obtain the correct secondary current. The voltage-core loss current curve and flux-magnetizing current curves, which are different from the conventional curves, are derived in this paper. The performance of the proposed algorithm is validated under various conditions using EMTP generated data. The experimental test results of an iron-core type electronic CT, which consists of the iron-core and the compensation board, are also included. The results indicate that the proposed algorithm can improve the accuracy of the measurement CT significantly, and thus reduce the size and the cost of the CT.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.49-51
• /
• 2004

The iron loss in electric machines takes large part of machine losses and the reduction of iron loss brings the increase of the efficiency. In the rotating machines, however it is very difficult to calculate the iron loss and to get the exact experiment result because the measuring precesses are very complex and laborious. As is well known, the relation between the flux density B and the magnetic field intensity H relation is not linear. For the iron loss, B and H must be measured and usually B becomes the reference wave(sine wave) and the following H is measured using H-coil. To make the B as sine wave, B is controlled by some devices. The error is controlled to become zero by the proposed algorithm which uses the bisection algorithm. The experiments are compared with the simulation results, and they show acceptable agreements.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.58-60
• /
• 1999

This paper presents dynamic performance prediction using Matlab / simulink after parameter estimation of synchronous reluctance motor considering iron loss. Test motor is 3 phase SynRM with the segmental rotor, rating power is 0.175KW. Experiment equipment is consists of testing motor, dynamometer, vector invertor dynamocontroller, and power analyser. The stator iron loss and rotor iron loss are modelled by additional windings on three-phase winding axis. These windings are transformed into d-q axis, and are represented as equivalent eddy current windings. P-Q circle diagram method and single phase standstill method are used to measure motor parameters considering iron loss.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2347-2349
• /
• 2004

The iron loss in electric machines takes large part of machine losses and the reduction of iron loss brings the increase of the efficiency. In the rotating machines, however it is very difficult to calculate result because the measuring processes are very complex and laborious. As is well known, the relation between the flux density B and the magnetic field intensity H relation is not linear. For the iron loss, B and H must be measured and usually B becomes the reference wave(sine wave) and the following H is measured using H-coil. To make the B as sine wave, B is controlled by some devices. The error is controlled to become zero by the proposed algorithm which uses the bisection algorithm. The experiments are compared with the simulation results, and they show acceptable agreements.

• Corrosion Science and Technology
• /
• 제8권1호
• /
• pp.21-26
• /
• 2009

The influence of $H_2S$ on the corrosion of iron and the corrosion prevention mechanism of an inhibitor was investigated with a differential capacitance measurement and a weight loss measurement method. The results show that $H_2S$ accelerates both the anodic iron dissolution and the cathodic hydrogen evolution in most cases. However, $H_2S$ acts as an inhibitor of the corrosion of iron under certain special conditions. An EIS method is proposed to explain the ability of inhibitors.