• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.394-395
• /
• 2011

In order to increase the power conversion efficiency and improve the power factor, a modified forward converter is proposed, which adopts a capacitive output filter instead of the inductive output filter of the conventional forward converter. Therefore, the proposed converter has wide input voltage range in opposite to that of the conventional forward converters. Moreover, the proposed converter uses the critical conduction mode for automatic current shaping to improve the power factor. As a result, the proposed converter can achieve quasi-resonant zero-voltage-switching, which can minimize the switching loss of main MOSFET. In addition, the operational principle of the proposed converter is analyzed and the characteristic of the proposed converter is investigated in this paper. To validate the effectiveness of the proposed converter, a prototype of 13W is implemented and the experimental results are discussed in more detail.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.9
• /
• pp.650-656
• /
• 2004

This paper presents block and timing diagrams of the DWA(data weighted averaging) to optimize a feedback time delay of the sigma-delta modulator. Through the Matlab modeling, the optimized coefficients of the integrators are obtained to design the modulator. And then the fully differential SC integrators, feedback DAC, 9-level quantizer, and DWA are designed by considering the nonideal characteristics of the modulator. The designed second-order multibit modulator is fabricated in a 0.35$\mu\textrm{m}$ CMOS process. The designed modulator achieves 73dB signal-to-noise ratio and 72dB dynamic range at 1.2Vp-p 585kHz input singal and 52.8MHz sampling frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.2
• /
• pp.141-148
• /
• 1998

For developing a beam shaping antenna, the circumference and the length of the vertical and horizontal elements of the Modified Transmission Line type Antenna(MTLA) are varied. The vertical radiation pattern of MTLA which has various shape was analyzed by the moment method in order to verify the beam tilt characteristics. From the analysis, it is confirmed that the condition of the maximum beam tilt is determined by the length of the vertical elements of the antenna. The antennal with the maximum beam tilt was designed and its input impedance and the radiation pattern was calculated theoretically and measured experimentally.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.51-56
• /
• 2008

Thermoforming is one of the most versatile and economical processes available for shaping polymer products, but obtaining a uniform thickness of the final product using this method is difficult. Heater power adjustment is very important because the thickness distribution depends strongly on the distribution of the sheet temperature. In this paper, the steady-state optimum distribution of heater power is first ascertained by a numerical optimization to obtain a uniform sheet temperature. The time-dependent optimal heater input is then determined to decrease the temperature difference through the direction of the thickness using the response surface method and the D-optimal method. The optimal results show that the time-dependent optimum heater power distribution gives an acceptable uniform sheet temperature in the forming temperature range by the end of the heating process.

• Journal of the Optical Society of Korea
• /
• v.20 no.3
• /
• pp.407-412
• /
• 2016

We analyzed through numerical simulations the properties of a square beam homogenizer near the target for laser shock peening. The efficiency was calculated near the target by considering the plasma threshold of the metals. We defined the depth of focus of the square beam homogenizer with a given efficiency near the target. Then, we found the relationship between the depth of focus for the laser shock peening and four main parameters of the square beam homogenizer: the plasma threshold of the metal, the number of lenslets in the array-lens, the focal length of the condenser lens and the input beam size.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.4
• /
• pp.29-35
• /
• 2008

In this paper, a new guidance law to reduce sensitivity to the initial heading errors is proposed. In order for shaping the input weights over the flight, we introduce the distribution functions expressed in terms of time-to-go and its inverse term. By applying the optimal control theory with the synthesized weights, the homing guidance law is derived. Also the characteristics of the proposed law are examined. Various computer simulations show the good performance of the proposed guidance.

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.128-131
• /
• 2001

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal, resulting in low total heat input. The effects of $CO_2$ laser cladding with powder feeding on mechanical properties of VERSAlloy were studied. Their low melting point (under 1093$^{\circ}C$) enables overlays to be applied with minimum dilution and base metal distortion. Experiment results indicated that powder feeding speed and quantity were important for laser cladding with powder feeding. The powder feeding speed should be adapted according to cladding speed for good shaping of clad layer. The effect of heat on the HAZ size can be limited and the growth of grain size of HAZ size was not serious.

• Journal of Drive and Control
• /
• v.16 no.1
• /
• pp.29-35
• /
• 2019

The control performance of hydraulic systems is basically influenced by the performance of electrohydraulic servo valve incorporated in a hydraulic control system. In this study, a control design was proposed to improve the control performance of a servo valve with a non-contact eddy current type position sensor. A mathematical model for the valve was obtained through an experimental identification process. A PI-D control together with a feedforward (FF) control was applied to the valve. To further improve the dynamic response of the servo valve, an input shaping filter (ISF) was incorporated into the valve control system. Finally, the effectiveness of the proposed control system was verified experimentally.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1131-1136
• /
• 2014

Recently, power converters installed on the specialized vessels such as LNG Carrier and Icebreaker and offshore plants mainly use diode rectifier. However, such devices cause distortion of supply voltage waveform by involving much harmonics to input current of non linearity load in rectifying operation. Distortion of supply voltage waveform can be problems such as false operation of generator, transformer and load device and deterioration of power quality. This thesis is focusing with a view to producing accurate sinusoidal AC waveform with certain load through improvement of distortion of current waveform causing under operation of rectifier by using accurate circuit of DC shaping. The result of computer simulation proved that harmonics involved in current and voltage waveform of power system can be reduced.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.162-167
• /
• 2013

X-ray or ${\gamma}$-ray spectroscopy systems are widely used for analyzing material characteristics. Pile-up pulses are very often encountered for several reasons in XRF systems. Thus, it is necessary to reject or recover pile-up pulses to accurately analyze the material under test. In this paper, a pile up pulse rejection and recovery method is presented for XRF systems using trapezoidal pulse shaping of the input signals. Since the proposed method is based on the trapezoidal pulse shaping method widely-used in XRF systems, only two counters and a few registers are needed to implement the additional function of pile-up pulse rejection and recovery. Consequently, the proposed system is much simpler than conventional pulse reconstruction systems. It is shown that the proposed method can detect and reject pile-up pulses exactly. It is also shown that the pile-up pulses can be recovered if some conditions are satisfied.