• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2022년도 추계학술대회
• /
• pp.337-340
• /
• 2022

SQL Injection 공격은 오래된 공격기법 중 하나로 웹 서비스에 대한 해킹 시도 유형 중에서도 높은 비중을 차지하고 있다. SQL Injection 공격은 데이터 노출 및 권한획득 등의 방법으로 현재까지도 해킹 시도가 많이 발생하고 있으며, 본 논문에서는 오픈소스인 ELK Stack을 활용하여 실시간으로 SQL Injection 공격 대응할 수 있는 로그 분석시스템을 구현하였다. 구현한 시스템을 통해 SQL Injection 공격에 대한 로그 데이터를 시각화하여 제공함으로써, 사용자는 공격의 위험도를 쉽게 파악할 수 있으며 신속하게 공격에 대비할 수 있을 것으로 기대한다.

• 터널과지하공간
• /
• 제26권1호
• /
• pp.12-23
• /
• 2016

향후 국내에서 수행될 이산화탄소 지중저장 프로젝트의 성공적인 수행을 위해서는 현장 지질조건에 최적화된 주입 조건을 설계하는 것이 중요하다. 따라서 본 연구에서는 주입량 및 주입온도 등의 주입조건이 격리저장시스템의 역학적 안정성에 미치는 영향을 열-수리-역학 연계해석기법의 하나인 TOUGH-FLAC 해석기법을 이용하여 평가하였다. 저장시스템의 역학적 안정성은 기존 균열의 전단미끄러짐 발생가능성을 활동마찰각 및 응력원을 이용하여 분석하였다. 이산화탄소의 주입온도가 저류층의 초기온도보다 낮은 저온주입의 조건에도 열응력으로 인한 인장균열은 발생하지 않는 것으로 파악되었으나, 저류층에서 전단미끄러짐이 발생하는 결과를 보였다. 단위시간당 이산화탄소 주입량을 변화시킨 시나리오 해석에서는 단계별로 주입량을 감소시키는 주입시나리오에서 기존 균열들의 전단미끄러짐 발생 가능성이 가장 낮은 것으로 평가되었다.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.309-316
• /
• 2017

In injection molding, the quality of an injection molded product varies greatly depending on the molding conditions. Many researche studies have been conducted on the quality analysis of molded parts according to the molding conditions such as injection pressure, injection temperature, and packing pressure. However, there have not been many studies on the V/P switchover timing. It is known that when a large pressure is applied to a cavity in the packing phase, the cavity pressure is most affected by the packing pressure. In addition, depending on the position (timing) of the packing pressure, it can have a direct influence on quality based on the shrinkage and dimensions of the molded parts. In this study, the change in pressure profile in the cavity according to the V/P switchover position is confirmed. A CAE analysis program (Moldflow) was used to simulate and analyze two models using the PC and PBT materials. In order to compare these results with the actual injection molding results, injection molding was performed for each V/P switchover position, and the correlation between simulation and experiment, especially for the shrinkage of molded parts, was evaluated.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.107-114
• /
• 2009

A Common-Rail Direct Injection (CRDI) system for high speed diesel engines was developed to meet reductions of noise and vibration, emission regulations. High pressure in the common rail with electric control allows the fuel quantity and injection timing to be optimized and controlled throughout a wide range of engine velocity and load conditions. In this study, CRDI system analysis model which includes fuel and mechanical systems was developed using commercial software, AMESim in order to predict characteristics for various fuel injection components. The parameter sensitivity analysis such as throttle size, injection rate, plunger displacement, supply pressure of fuel injection for system design are carried out.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.110-118
• /
• 1995

The filling phase analysis of the injection molding process for thermoplastics was applied to predict pressure, themperature and shear stress in the test mold, and the results were compared with the experiment using 30% glass fiber added ABS resin. The finite difference method was used in the analysis considering the effects of heat transfer between molten polymer and mold wall, and also frictional heating by shear flow. The analysis results were considered as a method to improve the quality and the productivity of injection molding process. Using the analysis results, the molding factors such as mold-ability of polymers, performance of injection molding machine, positioning of gate and dimendsioning of runner in the injection molding process can be estimated at the design stage of mold for good quality and productivity.

• 한국임상수의학회지
• /
• 제38권3호
• /
• pp.105-114
• /
• 2021

Intra-articular injection of ELHLD peptide is considered to have a therapeutic effect in osteoarthritis (OA) through the inhibition of transforming growth factor-β1. This study aimed to assess the efficacy of intra-articular injections of high-dose ELHLD peptide (100 ㎍/kg) in canine stifle OA. Six client-owned dogs diagnosed with stifle OA were included. Selected dogs were treated with an intra-articular injection of high-dose ELHLD peptide (100 ㎍/kg). Outcome measures, including orthopedic examination, gait analysis, and Canine Brief Pain Inventory (CBPI) score, were evaluated four times after injection. Orthopedic examination, gait analysis, and owner's assessment (CBPI) improved significantly from 4 weeks after injection. In conclusion, we obtained sufficient evidence from this small sample that high-dose ELHLD peptide improves clinical signs of canine OA not only through subjective assessment but also through objective evaluation.

• Nuclear Engineering and Technology
• /
• 제54권6호
• /
• pp.2031-2036
• /
• 2022

Energetic particle strikes the device and induces data corruption in the configuration memory (CRAM), causing errors and even malfunctions in a system on chip (SoC). Software-based fault injection is a convenient way to assess device performance. In this paper, dynamic partial reconfiguration (DPR) is adopted to make fault injection on a Xilinx 16 nm FinFET Ultrascale+ MPSoC. And the reconfiguration module implements the Sobel and Gaussian image filtering, respectively. Fault injections are executed on the static and reconfiguration modules' bitstreams, respectively. Another contribution is that the failure modes and effects analysis (FMEA) method is applied to evaluate the system reliability, according to the obtained injection results. This paper proposes a software-based solution to estimate programmable device vulnerability.

• Korea-Australia Rheology Journal
• /
• 제20권2호
• /
• pp.79-88
• /
• 2008

In this study, we focus on the improvement of the filling efficiency in injection molding by application of ultrasonic vibration. While studies about the filling efficiency of typical filling processes in the injection molding have been widely performed, there have been only few studies about the filling efficiency of an ultrasonic process. The effect of the ultrasonic vibration is an important process condition, which influences the flow characteristics of polymer melt. This new condition even affects well-known injection conditions such as cavity pressure, injection temperature and mold temperature. For this study, we carried out a numerical analysis by appropriate modeling and analysis of the ultrasonic process in the filling process. To verify this numerical analysis, we compared the numerical results with the experimental data. Also, we analyzed the filling process in a thin cavity using this numerical analysis. To understand the flow characteristics of polymer melt in the ultrasonic process, we substituted real and complex vibration conditions with simplified and classified conditions according to the position of vibrating cavity surfaces and the phase difference between two opposing cavity surfaces. We also introduced MFR (melt flow ratio) as a new index to estimate the filling efficiency in the ultrasonic process.

• 소성∙가공
• /
• 제16권1호
• /
• pp.25-30
• /
• 2007

The present study covers an integrated simulation method to evaluate optical performance of an aspheric plastic lens by connecting a finite element (FE) analysis of injection molding with a ray tracing simulation. Traditional ray tracing methods have based on the assumption that the optical properties of a lens are homogeneous throughout the entire volume. This assumption is to a certain extent unrealistic for injection-molded plastic lenses because material properties vary at every point due to the injection molding effects. To take into account the effects of the inhomogeneous optical properties of the molded lens, a new.ay tracing scheme is proposed in conjunction with a FE analysis of the injection molding. A numerical scheme is developed to calculate ray paths on every element layer with more realistic information of the refractive indices which can be obtained through the FE analysis. This information is then used to calculate the ray paths based on the FE mesh of which nodal points have unique index values. The proposed tracing scheme is implemented on the tracing of an aspheric lens, and its validity is ascertained through experimental verification.

• 설비공학논문집
• /
• 제19권12호
• /
• pp.811-820
• /
• 2007

A Study on the optimal design of the AIG(Ammonia Injection Grid) to improve the performance of DeNOx facilities in the HRSG(Heat Recovery Steam Generator) was performed using the CFD analysis. On the basis of the flow analysis results in the case that the AIG in the HRSG was not installed, the numerical analyses according to the positions of AIG, injection angles of nozzle and the control of ammonia injection quantity were carried out. The standard deviation according to factors was calculated for quantitative comparison. As the results, the AIG in the HRSG should be installed in the position that the uniform flow field shows through the exact flow analysis in the previous of the AIG design and installation. In the case the AIG has already been installed and non uniform flow distribution shows, it is recommended that flow correction device or KoNOx catalyst should be used. Otherwise, the control of ammonia injection angle or the ammonia injection quantity using the velocity profile analysis is demanded to accomplish the optimal performance.