• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.270-277
• /
• 2003

Thermal performance of flip chip bonding with Sn-3.5Ag solder ball was studied. The temperature distribution was measured with IR(InfraRed) camera of 25 urn resolution. The measurement shows that most of the samples had much higher maximum temperature than average temperature. With central heater and 2.5 (W), the difference between maximum and average temperature is over $80^{\circ}C$. The distribution was influenced by the location of heater, the distance from heater to flip chip bonding, and the passivation opening of solder bumps. To reduce the maximum temperature, the bigger passivation opening, the smaller chip size, and the closer location of heater to flip chip bumps are preferrable.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.131-139
• /
• 2014

Infra-gravity waves (IGWs) with a period of 1~3 minutes are a factor that directly influences the motion analysis of moored ships inside a harbor and longshore sediment transport analysis. If significant levels of IGWs from far seas are transferred to a harbor and amplified, they may cause downtime of large ships and induce economic loss. In this study, transfer characteristics of the IGWs intruding from outside to inside Pohang New Harbor were analyzed using statistical analysis and transfer function of wave data measured at both outside and inside the harbor for around 5 years. Transfer characteristic analysis was limited to events where IGWs had wave heights above 0.1 m. The wave height distribution of inside the harbor was similar to that of outside the harbor, while the wave period variance of the former was larger than that of the latter. The parameters of the transfer function was optimally estimated according to each event. The estimated average RMS error of the wave height inside the harbor was around 0.013 m. The estimated parameters had a strong correlation with the linear combination information of IGW wave height, period, and direction (R = 0.95). The transfer function suggested in this study can quickly and easily estimate information on IGWs inside the harbor using IGW information predicted beforehand, and is expected to reduce damage due to unexpected restrictions on harbor usage.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.60.2-60.2
• /
• 2018

We present the near infrared JHK photometric properties and the spatial distribution of red supergiants(RSGs) of NGC 3623, NGC 3627 and NGC 3628 in the Leo Triplet system using the data obtained with 3.8m UKIRT(United Kingdom Infra-Red Telescope) at Hawaii. We checked interaction between the three galaxies by making a spatial density map of RSGs. From (J-K,K)0 Color-Magnitude Diagram which include resolved stars in three galaxy and control field with PARSEC isochrone, we figured out the RSG candidates of the Leo triplet are at 0.9<(J-K)0<1.2, mK<17.5 and separated them from background and foreground sources. Using gaussian kernel density estimation, we drew spatial density map of RSGs in the Leo triplet with an assumption that all RSGs are an identical population. The density map shows extended features of NGC 3628 to NGC 3627 along the declination direction. The asymmetries between NGC 3627 and NGC 3628 might be evidence for that the distribution of actual star components(RSGs) follows the neutral hydrogen distribution and also for interaction between two galaxies. And the extended features along the right ascension direction might be a supporting evidence for the existence of a TDG(Tidal Dwarf Galaxy). In case of NGC 3623, we could not see any sign of interaction in density map.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.4
• /
• pp.127-137
• /
• 2010

The today many companies are tilting to enjoy the dominant position in the globalization of global market. The past business management is focus on the price and quality, but many companies are doing our utmost for customer satisfaction of various needs of customers. Therefore, The efficient logistics management is a core element in the competitiveness of company that respond more quickly and effectively to market. Now, The companies are building an integrated SCM(Supply Chain Management) system that is able to manage and operate procurement, production, distribution & logistics activity. Among the IT infra, The RFID technique is received special attention for this successful SCM System, continuously it is being researched and developed. Also, they recognize RFID techniques that offer various services at supply chain flow, create value of company. This study propose implications in other industry for biz model development and direction based on RFID in many industry through case study for development of the distribution logistics information system on using RFID.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.63-71
• /
• 2011

Three-dimensional finite element analysis is performed to study the temperature distribution phenomenon of TIG assisted friction stir welding (TAFSW) between dissimilar plates (Al 6061-T6 and stainless steel 304). TAFSW is a solid-state welding process that integrates TIG (Tungsten Inert Gas) into a friction stir welding (FSW), to preheat the harder material ahead of FSW tool during welding. In order to facilitate the industrial application of welding, 3D numerical modeling of heat transfer has been carried out applying Finite Element Method (FEM). The temperature distribution due to heat generation during TAFSW on dissimilar materials joint is analysed using in-house solver. Moving heat source along with frictional heat between the work specimens and tool surface is considered to calculate the heat input. The analytical model used predicts successfully the maximum welding temperatures that occur on the dissimilar materials during TAFSW. Comparison with the infra red camera and thermocouple measurement results shows that the results from the current numerical simulation have good agreement with the measured data.

• Journal of Digital Convergence
• /
• v.17 no.2
• /
• pp.59-71
• /
• 2019

This research is aimed to identify the building factors and deriving the importance of each factor for establishing the smart distribution center in the fourth industrial revolution era. The research methodology used CFPR(Consistent Fuzzy Preference Relations) to effectively extract expert knowledge. Research has shown as principle factors that "Service" is the first factor to be considered as 0.271, followed by "Infra(Warehouse)"(0.254), "Information System"(0.247), and "Equipment"(0.228). And as detailed factors, "Reliability" showed the highest importance as 0.091, followed "Visibility of Information System"(0.076), "Space Advancement"(0.075), "Location"(0.074) and "Satisfaction of service"(0.073). This study has implications in that it has presented an establishment direction for the smart distribution center.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.5
• /
• pp.701-708
• /
• 2021

In this paper, I investigate the performances of the discovery and the message transmission of the DDS (Data Distribution Service) included the security function. The DDS serves the communication protocol, a publication- subscription method, for the real-time communication in the distributed system. The publication-subscription method is used in the various area in terms of defence, traffic and medical due to the strength such as a performance, scailability and availability. Nowadays, many communication standard has included and re-defined the security function to prepare from dramatically increased a threat of the security, the DDS also publishes the standard included the security function. But it had been not researched that the effect of increased a overhead for legacy systems due to the using of the security DDS function. The experimental results show that the comparative performance of legacy DDS and security DDS in terms of the discovery and the message transmission.

• International Commerce and Information Review
• /
• v.15 no.3
• /
• pp.135-153
• /
• 2013

This study aims to investigate the overall relationship between the deterring and facilitating factors in export activities of the small and medium export companies. Nine export deterring factors are analyzed by multinational dimensional scaling(MDS) method to identify key dimensions underlying those factors. Perceptual mapping shows that some factors such as brand image, operating capital and e-trade infra are found similar in its degree of difficulties in export activities. Regression analysis shows that government export promotion measures might play an effective export facilitating factors to ease the export deterring factors like market information and manufacturing skill. Whereas difficulties arising from e-trade infra, operating capital, and brand image might be eliminated by internal competency of company, difficulties from distribution channel might be lessened by overseas orientation of chief executive of company.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.35-43
• /
• 2017

A 3D transient heat transfer model is developed by ABAQUS software to study the temperature distribution during friction stir welding process at different rotational speeds. Furthermore, AA 5083-O plates were joined by FSW technique. For this purpose, a universal milling machine was used to perform the welding process and a mechanical vice was used to fix the work pieces in the proper position. The joints were friction stir welded at a constant travel speed 50 mm/min and two rotational speed values; 400 rpm and 630 rpm using two types of tools; cylindrical threaded pin and tapered smooth one. At each welding condition the temperature was measured using infra-red thermal image camera to verify the simulated temperature distribution. The welded joints were visually inspected as well as by macro- and microstructure evolutions. In addition, the welded joints were mechanically tested for hardness and tensile strength. The maximum peak temperature obtained was at higher rotational speed using the threaded tool pin profile. The results showed that the rotational speed affects the peak temperature, defects formation and sizes, and the mechanical properties of friction stir welded joints. Moreover, the threaded tool gives superior mechanical properties than the tapered one at lower rotational speed.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.3
• /
• pp.1674-1688
• /
• 2019

As environmental pollution and fossil fuel energy problems from fuel vehicle have occurred, the interest of electric vehicle(EV) has increased. EV industry and energy industry have grown dynamically in these days. It is expected that the next generation of primary transportation will be EV, and it is necessary to prepare EV infra and efficient energy management such as EV communication protocol, EV charge station, and smart grid. Those EV and energy industry fields are now on growth. Also, the study and development of them are now in progress. In this paper, distributed charge signal processing software for smart slow and quick EV charge is proposed and designed for dealing with EV charge demand. The software consists of smart slow and quick EV charge schedule engine and EV charge power distribution core. The software is designed to support two charge station types. One is normal EV charge station and the other is bus garage EV charge station. Both two types collect the data from EV charge stations, and then analyze the collected data. The software suggests optimized EV charge schedule and deliveries EV charge power distribution information to power switchboard system, and the designed software is implemented on embedded system. It is expected that the software provides efficient EV charge schedule.