• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.379-384
• /
• 2003

Noise is a problem in many electronic circuits and active control system. Arising from spuriously coupled noise from other circuits, it corrupts the signal of interest and introduces an uncertainty into information it contains. In this paper, re have researched noise characteristics of the inductive displacement sensor which has been designed. n first present basic concept and characteristics of magnetic field-coupled noise in the sensor output signal. Then, n are present relation noise and sensor performances. Finally, we concentrate low noise design of a sensor driver and a signal detection circuit.

• Journal of information and communication convergence engineering
• /
• 제14권4호
• /
• pp.268-271
• /
• 2016

An efficient inductive switching noise suppression technique for mixed-signal integrated circuits (ICs) using standard CMOS digital technology is proposed. The proposed design technique uses a parallel RC circuit, which provides a damping path for the switching noise. The proposed design technique is used for designing a mixed-signal circuit composed of a ring oscillator, a digital output buffer, and an analog noise sensor node for $0.13-{\mu}m$ CMOS digital IC technology. Simulation results show a 47% reduction in the on-chip inductive switching noise coupling from the noisy digital to the analog blocks in the same substrate without an additional propagation delay. The increased power consumption due to the damping resistor is only 67% of that of the conventional source damping technique. This design can be widely used for any kind of analog and high frequency digital mixed-signal circuits in CMOS technology

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.250-254
• /
• 2001

The resolution of analog sensor is determined by its sensitivity and amplitude of noise. This paper presents modeling of inductive gap sensor base on equivalent magnetic circuit and analysis of sensitivity. We can simulate static characteristic of inductive gap sensor using this model. Computer simulation show that sensor's sensitivity is affected by magnetic flux's leakage and fringing, and that they are affected by shape of sensor probe. Base on this, we designed shape of inductive position sensor probe.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.249-252
• /
• 1997

The resolution of analog sensor is determined by its sensitivity and amplitude of noise. This paper presents modeling of inductive gap sensor base on equivalent magnetic circuit and analysis of sensitivity. The model of inductive gap sensor is verified by the experimental results. Then we can simulate static characteristic of inductive gap sensor using this model. Computer simulation show that sensor's sensitivity and linearity are affected by magnetic flux's leakage and fringing, and that they are affected by shape of sensor probe.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1038-1041
• /
• 2003

The magnetic suspension system is used in many areas, because it has great advantages. such as no friction, no noise, no lubrication and so on, but it is a unstable system in natural. It must have a feedback control with the position is measured for a stable levitation. There are an eddy-current sensor, a capacitive sensor, an inductive sensor, and an optical sensor with a laser as the sensor which measures displacements without contact. Among them, an inductive sensor is made with lower price than others. And it has a good linearity. In this paper, a magnetic circuit leads a linear equation between an input as a displacement and an output as a voltage. Experiments establish that voltage change according to displacement is linear. This paper presents the preliminary study of an inductive position sensing for self-sensing magnetic suspension system.

• ETRI Journal
• /
• 제26권1호
• /
• pp.57-60
• /
• 2004

We propose an inductive compensation method for a surface-mountable 10 Gbps photoreceiver module. Since many typical 10 Gbps photoreceiver modules consist of a photodetector and low-noise pre-amplifier, the impedance mismatch between the photodetector and pre-amplifier, as well as package parasitics, may reduce the frequency bandwidth. In this paper, we inserted an inductive component between the photodetector and pre-amplifier in order to create frequency bandwidth expansion. From the measurement results, we have found that the proposed technique can increase the -3 dB bandwidth about 4.2 GHz wider compared with an uncompensated module. And, from a bit-error rate (BER) test, we observed -15.7 dB sensitivity at $10^{-12}$ BER. This inductive compensation can be implemented easily and is compatible with common manufacturing processes of photoreceiver modules.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.405-408
• /
• 2000

We designed and fabricated VCO using inductive reactance variation at 2GHz. A varactor diode is one of the main devices in VCO, which varies capacitance depending on reverse voltage. In this paper, a varactor diode is not used as a variable capacitive reactance device but as an inductive device. The circuit design and simulation have been carried out using HP-MDS. The fabricated VCO is measured using the HP 8532B spectrum analyzer and the HP 4352B VCO/PLL analyzer. The experimental result shows the phase noise -110dBc/Hz at a 100kHz offset frequency, the control voltage sensitivity of 23MHz/V and a -3.5dBm output power with a D.C. current consumption of 5.9mA. The simulation and measurements show exact agreement except with regard to the oscillation frequency. The measured oscillation frequency is lower than the simulation result because there is some parasitic inductance in the PCB layout.

• 한국전자파학회논문지
• /
• 제24권11호
• /
• pp.1055-1063
• /
• 2013

저 잡음 증폭기는 RF 수신단의 필수적인 요소이며, 다양한 무선시스템에서 사용하기 위하여 넓은 주파수 범위에서 동작하도록 요구된다. 전압 이득, 반사 손실, 잡음 지수, 선형성과 같은 중요한 성능지표들을 신중히 다루어서, 제안하는 LNA의 주요한 성능으로 역할을 하게끔 한다. Buffer 단에서 peaking 인덕터를 사용하며 전체적으로 cascade 구조로써 inductive shunt feedback을 LNA 입력 단에 성공적으로 적용하였다. 광대역 정합 주파수를 얻기 위한 설계식은 상대적으로 간단한 회로구성을 통해 도출된다. 입력 임피던스의 주파수 응답 분석을 위하여 pole과 zero를 광대역 응답을 실현하기 위한 특성으로 기술하였다. 입력 단에 게이트와 드레인 사이의 인덕터는 출력의 3차 고조파를 감소시킴으로 선형성을 크게 향상시킬 수 있다. 제안하는 회로를 $0.18{\mu}m$의 CMOS 공정으로 제작하였고, Pad를 포함한 광대역 LNA의 칩 면적은 $0.202mm^2$이다. 측정 결과는 1.5~13 GHz에서 입력손실은 -7 dB 이하이고, 전압 이득은 8 dB 이상이며, 잡음 지수는 6~9 dB 정도이다. 그리고 IIP3는 8 GHz에서 2.5 dBm이며, 1.8 V 전압에서 14 mA 전류를 소모한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권1호
• /
• pp.100-108
• /
• 2014

Low noise amplifier (LNA) is an integral component of RF receiver and frequently required to operate at wide frequency bands for various wireless system applications. For wideband operation, important performance metrics such as voltage gain, return loss, noise figure and linearity have been carefully investigated and characterized for the proposed LNA. An inductive shunt feedback configuration is successfully employed in the input stage of the proposed LNA which incorporates cascaded networks with a peaking inductor in the buffer stage. Design equations for obtaining low and high impedance-matching frequencies are easily derived, leading to a relatively simple method for circuit implementation. Careful theoretical analysis explains that input impedance can be described in the form of second-order frequency response, where poles and zeros are characterized and utilized for realizing the wideband response. Linearity is significantly improved because the inductor located between the gate and the drain decreases the third-order harmonics at the output. Fabricated in $0.18{\mu}m$ CMOS process, the chip area of this wideband LNA is $0.202mm^2$, including pads. Measurement results illustrate that the input return loss shows less than -7 dB, voltage gain greater than 8 dB, and a little high noise figure around 6-8 dB over 1.5 - 13 GHz. In addition, good linearity (IIP3) of 2.5 dBm is achieved at 8 GHz and 14 mA of current is consumed from a 1.8 V supply.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제7권4호
• /
• pp.260-266
• /
• 2007

Analytical compact form models for the signal transients and crosstalk noise of inductive-effect-prominent multi-coupled RLC lines are developed. Capacitive and inductive coupling effects are investigated and formulated in terms of the equivalent transmission line model and transmission line parameters for fundamental modes. The signal transients and crosstalk noise expressions of two coupled lines are derived by using a waveform approximation technique. It is shown that the models have excellent agreement with SPICE simulation.