• Bulletin of the Korean Chemical Society
• /
• 제32권4호
• /
• pp.1133-1137
• /
• 2011

Ordered array of gold nanoparticles (Au NPs) over ITO glass was investigated in terms of ITO pretreatment, particle size, and diamines with different chain length. Owing to the indium-tin-oxide (ITO) layer coated on the glass, the substrate surface has a limited number of hydroxyl groups which can produce functionalized amine groups for Au binding, which resulted in the loosely-packed array of Au NPs on the ITO surface. Diamine ligand as a molecular linker was introduced to enhance the lateral binding of adjacent Au NPs immobilized on the amine-functionalized ITO glass, consequently leading to the densely-packed array of Au NPs over the ITO substrate. The molecular bridging effect was strengthened with the increase of chain length of diamines: C-12 > C-8. The packing density of small Au NPs (< 40 nm) was significantly increased with the increase of C-8 diamine, but large Au NPs (> 60 nm) did not produce densely-packed array on the ITO glass even for the dosage of C-12 diamine.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권10호
• /
• pp.449-452
• /
• 2005

We fabricated an electrochemical detector (ECD) to catalyze redox reaction efficiently by electrodepositing Prussian blue (PB) on the indium tin oxide (ITO) electrode. Capillary electrophoresis (CE) and amperometric method were used. We investigated the PB surface properties by topography from atomic force microscopy (AFM). Also PB film thickness calibration with respect to deposition time and voltage was used to get better PB surFace. The PB thin film of dense and smooth surface could catalyze redox reaction efficiently. Comparing with CE-ECD microchip using bare-lTO electrode, proposed CE-ECD microchip using PB deposited electrode has shown better sensitivity by determining the detected peak current from the electropherograms while the concentration of tested analyzes was maintained the same. It is verified that detection limit can be lowered for 0.01 mM of dopamine and catechol respectively.

• Bulletin of the Korean Chemical Society
• /
• 제34권2호
• /
• pp.421-425
• /
• 2013

The effect of pretreatment on indium-tin oxide (ITO) electrodes has been rarely studied, although that on metal and carbon electrodes has been enormously done. The electrochemical and surface properties of ITO electrodes are investigated after 6 different pretreatments. The electrochemical behaviors for oxygen reduction, $Ru(NH_3){_6}^{3+}$ reduction, $Fe(CN){_6}^{3-}$ reduction, and p-hydroquinone oxidation are compared, and the surface roughness, hydrophilicity, and surface chemical composition are also compared. Oxygen reduction, $Fe(CN){_6}^{3-}$ reduction, and p-hydroquinone oxidation are highly affected by the type of the pretreatment, whereas $Ru(NH_3){_6}^{3+}$ reduction is almost independent of it. Interestingly, oxygen reduction is significantly suppressed by the treatment in an HCl solution. The changes in surface roughness and composition are not high after each pretreatment, but the change in contact angle is substantial in some pretreatments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2404-2406
• /
• 2005

본 연구에서는 전기촉매제를 사용하여 증가된 감도를 가지는 검출 시스템을 제작하였다. 전극과 검출물질 사이의 산화환원반응을 촉진시키기 위한 물질로 Prussian blue (PB)를 indium tin oxide (ITO) 전극에 전착하였다. 본 실험에서는 분석물질의 이동 및 분리를 위하여 모세관 전기영동방법을 사용하였으며 측정방법은 전류량법을 사용하였다. 전착된 PB 박막의 특성은 원자 현미경으로 분석하여 0.1V, 3min의 전착조건으로 최적화하였다. 전기 촉매제로써의 PB의 특성을 확인하기 위하여 ITO 전극만을 사용한 전기화학적 검출기와 비교하였으며 본 연구에서 제안된 검출기의 감도가 20배정도 더 좋다는 것을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.7-7
• /
• 2010

Indium tin oxide (ITO) - SWNT nano crystalline composites was synthesized at low temperature(${\sim}250^{\circ}C$)using Nano Cluster Deposition technique by Metal Orhoganic Chemical Vapor Deposition method. XRD patterns of ITO- SWNT composite shows pure cubic phases without any secondary phase. I-V measurement gives resistance of 12 ohms for Sn doped (3 wt %) indium oxide-SWNT composites. The electrical conductivity of the nano composites is significantly enhanced compared to the SWNT.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.209-209
• /
• 2012

High-efficient transparent conductive oxide (TCO) film-embedding Si heterojunction solar cells were fabricated. An additional doping was not applied for heterojunction solar cells due to the spontaneous junction formation between TCO films and an n-type Si substrate. Three different TCO coatings were formed by sputtering method for an Al-doped ZnO (AZO) film, an indium-tin-oxide (ITO) film and double stacks of ITO/AZO films. An improved crystalline ITO film was grown on an AZO template upon hetero-epitaxial growth. This double TCO films-embedding Si heterojunction solar cell provided significantly enhanced efficiency of 9.23% as compared to the single TCO/Si devices. The effective arrangement of TCO films (ITO/AZO) provides benefits of a lower front contact resistance and a smaller band offset to Si leading enhanced photovoltaic performances. This demonstrates a potential scheme of the effective TCO film-embedding heterojunction Si solar cells.

• 센서학회지
• /
• 제16권3호
• /
• pp.229-233
• /
• 2007

The indium tin oxide (ITO) films were deposited on CR39 substrate using DC magnetron sputtering. The ITO thin films deposited at room temperature because CR39 substrate its glass-transition temperature is $130^{\circ}C$. The ITO thin films used bottom and top electrode and for organic thin film transparent transistors (OTFTs). The ITO thin film electrodes electrical properties and optical transparency properties in the visible wavelength range (300-800 nm) strongly dependent on volume of oxygen percent. For the optimum resistivity and transparency of the ITO thin film electrode achieved with a 75 W plasma power, 10 % volume of oxygen and a 27 nm/min deposition rate. Above 85 % transparency in the visible wavelength range (300-800 nm) measured without post annealing process and a low resistivity value $9.83{\times}10^{-4}{\Omega}cm$ was measured thickness of 300 nm. All fabrication process of ITO thin films did not exceed $80^{\circ}C$.

• Applied Science and Convergence Technology
• /
• 제25권6호
• /
• pp.128-132
• /
• 2016

We investigated the effect of Ar ion sputtering on the surface electronic structure of indium tin oxide (ITO) using X-ray and ultraviolet photoelectron spectroscopy (XPS and UPS) measurements with increasing Ar ion sputtering time. XPS measurements revealed that surface contamination on ITO was rapidly removed by Ar ion sputtering for 10 s. UPS measurements showed that the work function of ITO increased by 0.2 eV after Ar ion sputtering for 10 s. This increase in work function was attributed to the removal of surface contamination, which formed a positive interface dipole relative to the ITO substrate. However, further Ar ion sputtering did not change the work function of ITO although the surface stoichiometry of ITO did change. Therefore, removing the surface contamination is critical for increasing the work function of ITO, and Ar ion sputtering for a short time (about 10 s) can efficiently remove surface contamination.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.605-608
• /
• 2008

The preparation and characteristics of flexible indium tin oxide electrodes grown on polyethylene terephthalate (PET) substrates using a specially designed roll-to-roll sputtering system for use in flexible optoelectronics In spite of low a PET substrate temperature, we can obtain the flexible electrode with a sheet resistance of 47.4 ohm/square and an average optical transmittance of 83.46 % in the green region of 500~550 nm wavelength. Both x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis results showed that all flexible ITO electrodes grown on the PET substrate were an amorphous structure with a very smooth and featureless surface, regardless of the Ar/$O_2$ flow ratio due to the low substrate temperature, which is maintained by a cooling drum. In addition, the flexible ITO electrode grown on the Ar ion beam treated PET substrates showed more stable mechanical properties than the flexible ITO electrode grown on the wet cleaned PET substrate, due to an increased adhesion between the flexible ITO and the PET substrates.

• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.49-55
• /
• 2015

This paper reports solution-processed, high-efficiency organic light-emitting diodes (OLEDs) fabricated by a knife coating method under ambient air conditions. In addition, indium tin oxide (ITO), traditionally used as the anode, was substituted by optimizing the conductivity enhancement treatment of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films on a polyethylene terephthalate (PET) substrate. The transmittance and sheet resistance of the optimized PEDOT:PSS anode were 83.4% and $27.8{\Omega}/sq$., respectively. The root mean square surface roughness of the PEDOT:PSS anode, measured by atomic force microscopy, was only 2.95 nm. The optimized OLED device showed a maximum current efficiency and maximum luminous density of 5.44 cd/A and $8,356cd/m^2$, respectively. As a result, the OLEDs created using the PEDOT:PSS anode possessed highly comparable characteristics to those created using ITO anodes.