• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.660-665
• /
• 2003

The true stress - true strain relation of SA508 steel was evaluated with analytical and experimental equation on the base of the indentation load-depth curve obtained from the modeling of ball indentation test. The evaluated relation between true stress and true strain is agreed well with that of SA508 teel defined in the modeling. The distribution of effective stress along the center axis of indentation depth was calculated with Tresca criteria in the modeling. The representative strain, which are defined in this study as the corresponding strains obtained from the maximum effective stress, have a linear relation with the true strain. The true stress - true strain relation of austenitic stainless steel was evaluated by the modeling of ball indentation test to verify the case of A508 steel.

• 대한기계학회논문집A
• /
• 제28권3호
• /
• pp.304-310
• /
• 2004

In this paper, cracking threshold for nanoindentation is analyzed by using 3D finited-element method. The analysis by maximum principal stress criterion can obtain the reliable results for determining to crack initiation location and load. Because the ratio of maximum principal stress to indentation depth for Victors indentation is smaller than flat-plane-column indentation and cracking for Victors indentation occurs from the inner part of specimen difficult to measure crack length, the nanoindentation facture test for flat-plane-column indentation is more effective.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.355-363
• /
• 2023

The main purpose of this study is to characterize the size-dependent strain rate sensitivity in structural steel using the continue stiffness measurement (CSM) indentation. A series of experiments, such as CSM indentation and optical microscope examination, has been performed at the room temperature at different rate conditions. The results indicated that indentation hardness, strain rate, and flow stress showed size-dependent behavior. The dependency of indentation hardness, strain rate, and flow stress on the indentation size was attributed to the transition of the dislocation nucleation rate and the dislocation behaviors during the indentation process. Since both hardness and strain rate showed the size-dependent behavior, SRS tended to depend on the indentation depth. The results indicated that the SRS was quite high over 2.0 at the indentation depth of 240 nm and quickly dropping to 0.08, finally around 0.046 at large indents. The SRS values at large indentations strongly agree with the general range reported for several types of low-carbon steel in the literature (Chatfield and Rote 1974, Nguyen et al. 2018b, Luecke et al. 2005). The results from the present study can be used in both static and dynamic analyses of structures as well as to assess and understand the deformation mechanism and the stress-state of material underneath the indenter tip during the process of the indentation testing.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.76-81
• /
• 2011

UV imprinting process can manufacture high-functional optical components with low cost. If hard polymers can be used as transparent molds at this process, the cost will be much lower. However, there are limited researches to predict the machinability and the burr of hard polymers. Therefore, a new method to predict them by analyzing load-depth curves which can be obtained by the instrumented indentation test was developed in this study. The load-depth curve contains elastic deformation and plastic deformation simultaneously. The ratio of the plastic deformation over the sum of the two deformation is proportional to the ductility of materials which is one of the parameters of the machinability and the burr. The instrumented indentation tests were performed on the transparent molds of the hard polymers and the values of ratio were calculated. The machinability and the burr of three kinds of hard polymers were predicted by the ratio, and the prediction was in agreement with the experimental results from the machined surfaces of the three kinds of hard polymers.

• 대한기계학회논문집A
• /
• 제33권12호
• /
• pp.1357-1365
• /
• 2009

In this study, we enhance the numerical approach of Lee et al.$^{(1)}$ to spherical indentation technique for property evaluation of hyper-elastic rubber. We first determine the friction coefficient between rubber and indenter in a practical viewpoint. We perform finite element numerical simulations for deeper indentation depth. An optimal data acquisition spot is selected, which features sufficiently large strain energy density and negligible frictional effect. We then improve two normalized functions mapping an indentation load vs. deflection curve into a strain energy density vs. first invariant curve, the latter of which in turn gives the Yeoh-model constants. The enhanced spherical indentation approach produces the rubber material properties with an average error of less than 3%.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1-6
• /
• 2008

Due to the self-similarity of Berkovich and conical indenters, different materials may show the same loaddepth curve for single indentation. In this study, we first compare the load-depth characteristics of conical and Berkovich indenters via finite element method. We also analyze the variation of load-depth curves with angle of Berkovich indenter, indentation parameters, and material properties. With numerical regressions of obtained data, we then propose dual-Berkovich indentation formulae for material property evaluation. The proposed approach provides the values of elastic modulus, yield strength and strain-hardening exponent and corresponding stress-strain curve with an average error of less than 3%. The method is valid for any elastic indenters made of tungsten carbide and diamond for instance.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.138-143
• /
• 2004

Recently there has been a great world-wide interest in developing and characterizing new nano-structured materials. These newly developed materials are often prepared in limited quantities and shapes unsuitable for the extensive mechanical testing. The development of depth sensing indentation methods have introduced the advantage of load and depth measurement during the indentation cycle. In the present work, ZnO thin films are prepared on Si(111), Si(100) substrates at different temperatures by pulsed laser deposition(PLD) method. Because the potential energy in c-axis is low, the films always show c-axis orientation at the optimized conditions in spite of the different substrates. Thin films are investigated by X-ray diffractometer and Nano indentation equipment. From these measurements it is possible to get elastic modulus and hardness of ZnO thin films on Si substrates.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 1997년도 추계학술발표회 논문집
• /
• pp.78-85
• /
• 1997

Indentation and small punch tests are very powerful methods to monitor the materials reliability since they are very simple, easy and almost non-destructive. First, recently-developed continuous indentation test can provide the more material properties such as hardness, elastic modulus, yield strength, work-hardening exponent, etc., than the conventional hardness test. In our study, the true stress-strain curve was derived from the indentation load-depth curve for spherical indentation. In detail, the strain was able to be obtained from plastic depth/contact radius ratio, and the flow stress was from mean contact pressure through the analysis of elastic-plastic indentation stress field. Secondly, the small punch test was studied to evaluate the fracture toughness and defomation properties such as elastic modulus and yield strength. Like the indentation test, this test can be applied without severe damage of the target structure.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.668-674
• /
• 2002

Structural integrity assessment is indispensable for preventing catastrophic failure of industrial structures/components/facilities. This diagnosis of operating components should be done periodically for safe maintenance and economical repair. However, conventional standard methods for mechanical properties have the problems of bulky specimen, destructive and complex procedure of specimen sampling. Especially, the mechanical properties at welded zone including weldment and heat affected zone could not be evaluated individually due to their size requirement problem. So, an advanced indentation technique has been developed as a potential method for non-destructive testing of in-field structures. This technique measures indentation load-depth curve during indentation and analyzes the mechanical properties related to deformation such as yield strength, tensile strength and work-hardening index. Also indentation technique can evaluate a residual stress based on the concept that indentation load-depth curves were shifted with the direction and the magnitude of residual stress applied to materials. In this study, we characterized the tensile properties and welding residual stress of various industrial facilities through the new techniques, and the results are introduced and discussed.

• 대한기계학회논문집A
• /
• 제38권9호
• /
• pp.943-951
• /
• 2014

마이크로/나노 압입시험에 사용되는 각뿔 혹은 원뿔형 압입자의 선단 형상은 제작한계 및 사용 중 마모 등으로 인해 필수적으로 곡면 형태를 띄게 된다. 많은 압입시험 관련 연구에서 각뿔형 압입자의 선단 형상은 편의상 구형으로 가정한 후, 얕은 압입에 대한 구형압입 이론식을 적용하고 있다. 이러한 가정에는 근본적으로 두 가지 문제점이 있는데, 첫 번째로 이론해의 정확성은 재료 물성치 및 압입자 형상에 따라 변화한다는 점이며, 두 번째로 각뿔형 압입자의 실제 선단 형상은 이상적인 구형이 아니라는 점이다. 본 연구에서는 유한요소해석에 기반하여 압입시험에 미치는 이 두 요소의 영향을 분석한다. 먼저 탄성 구형 압입시험에 대해 푸아송비와 하중-변위 곡선의 상관관계를 살펴보고, 이를 기반으로 수정된 구형 탄성 압입 관계식을 제시한다. 이어 가정된 Berkovich 선단 형상의 3차원 유한요소해석으로부터 압입깊이에 따른 하중-변위 곡선의 특성을 분석한다.