• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1055-1063
• /
• 2013

Low noise amplifiers(LNAs) are an integral component of RF receivers and are frequently required to operate at wide frequency bands for various wireless systems. For wideband operation, important performance metrics such as voltage gain, return loss, noise figures and linearity have been carefully investigated and characterized for the proposed LNA. An inductive shunt feedback configuration is successfully employed in the input stage of the proposed LNA which incorporates cascaded networks with a peaking inductor in the buffer stage. Design equations for obtaining low and high input matching frequencies are easily derived, leading to a relatively simple method for circuit implementation. Careful theoretical analysis explains that poles and zeros are characterized and utilized for realizing the wideband response. Linearity is significantly improved because the inductor between gate and drain decreases the third-order harmonics at the output. Fabricated in $0.18{\mu}m$ CMOS process, the chip area of this LNA is $0.202mm^2$, including pads. Measurement results illustrate that input return loss shows less than -7 dB, voltage gain greater than 8 dB, and a little high noise figure around 7~8 dB over 1.5~13 GHz. In addition, good linearity(IIP3) of 2.5 dBm is achieved at 8 GHz and 14 mA of current is consumed from a 1.8 V supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.137-144
• /
• 2013

A delay-locked loop (DLL) that generates a 32-phase clock with the operating frequency of 125 MHz is introduced. The proposed DLL uses a delay line of $4{\times}8$ matrix architecture to improve a differential non-linearity (DNL) of the delay line. Furthermore, a integral non-linearity (INL) of the proposed DLL is improved by calibrating phases of clocks that is supplied to four points of an input stage of the $4{\times}8$ matrix delay line. The proposed DLL is fabricated by using $0.11-{\mu}m$ CMOS process with a 1.2 V supply. The measured operating frequency range of the implemented DLL is 40 MHz to 280 MHz. At the operating frequency of 125MHz, the measurement results shows that the DNL and INL are +0.14/-0.496 LSB and +0.46/-0.404 LSB, respectively. The measured peak-to-peak jitter of the output clock is 30 ps when the peak-to-peak jitter of the input clock is 12.9 ps. The area and power consumption of the implemented DLL are $480{\times}550{\mu}m^2$ and 9.6 mW, respectively.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.1
• /
• pp.21-31
• /
• 2008

response surface method (RSM) is widely used to evaluate th e extremely smal probability of ocurence or toanalyze the reliability of very complicated structures. Althoug h Monte-Carlo Simulation (MCS) technique can evaluate any system, the procesing time of MCS dependson the reciprocal num ber of the probability of failure. The stochastic finite element method could solve thislimitation. However, it is limit ed to the specific program, in which the mean and coeficient o f random variables are programed by a perturbation or by a weigh ted integral method. Therefore, it is not aplicable when erequisite programing. In a few number of stage analyses, RSM can construct a regresion model from the response of the c omplicated structural system, thus, saving time and efort significantly. However, the acuracy of RSM depends on the dist ance of the axial points and on the linearity of the limit stat e functions. To improve the convergence in exact solution regardl es of the linearity limit of state functions, an improved adaptive response surface method is developed. The analyzed res ults have ben verified using linear and quadratic forms of response surface functions in two examples. As a result, the be st combination of the improved RSM techniques is determined and programed in a numerical code. The developed linear adapti ve weighted response surface method (LAW-RSM) shows the closest converged reliability indices, compared with quadratic form or non-adaptive or non-weighted RSMs.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.1
• /
• pp.107-111
• /
• 2009

In this paper, the power added efficiency(PAE) of a Doherty amplifier has been improved by applying Photonic Bandgap(PBG) characteristics on the output of amplifier. As a result of the high order harmonics termination, excellent improvement in PAE, maximum output power as well as linearity is obtained. The PAE is improved as much as relatively 35% compared with a conventional Doherty amplifier. Moreover, size of LPF is reduced by PBG characteristics. Therefore the whole amplifier circuit size is considerably reduced by diminishing in size of the LPF as compared with a Doherty amplifier using conventional LPFs.

• Publications of The Korean Astronomical Society
• /
• v.32 no.1
• /
• pp.17-19
• /
• 2017

The first version of the AKARI far-infrared All-Sky Bright Source Catalogue (BSC ver.1) was released to public in March 2010. It has been widely used for various astrophysical researches. We are continuing efforts to produce the next edition. The new version is expected to be improved in accuracy and reliability, as well as its volume. Many improvements to the next version are in progress. The time-line signal is being re-examined throughout the entire data processing. Correction processes for signal linearity and detector responsivity, and procedure for masking signal anomaly are revised. The source extraction process is further tuned and operating parameters will be optimized. These bring better reliability of the source detection and possibly an increase of source numbers. The position accuracy is expected to be improved. Systematic position error seen around the Galactic plane will also be corrected. We also plan to deliver the Faint Source Catalogue version 1.

• Publications of The Korean Astronomical Society
• /
• v.32 no.1
• /
• pp.25-27
• /
• 2017

We are creating all-sky diffuse maps from the AKARI mid-infrared survey data with the two photometric bands centered at wavelengths of 9 and $18{\mu}m$. The AKARI mid-infrared diffuse maps achieve higher spatial resolution and higher sensitivity than the IRAS maps. In particular, the $9{\mu}m$ data are unique resources as an all-sky tracer of the emission of polycyclic aromatic hydrocarbons (PAHs). However, the original data suffer many artifacts. Thus, we have been developing correction methods. Among them, we have recently improved correction methods for the non-linearity and the reset anomaly of the detector response. These corrections successfully reduce the artifact level down to $0.1MJy\;sr^{-1}$ on average, which is essential for discussion on faint extended emission (e.g., the Galactic PAH emission). We have also made progress in the subtraction of the scattered light caused in the camera optics. We plan to release the improved diffuse maps to the public within a year.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.42-47
• /
• 2004

This research has improved the problem of discharge AND gate PDP proposed before. The polarity of the DC discharge which composes AND gate is reversely designed and the cross talk problem to the adjacent scanning electrode has been improved. The AND gate proposed before operated by using non-linearity of the discharge by the space charge. In this research, new discharge NOT logic in which it was used that an applied voltage changed with the discharge circuit was added to AND gate. AND gate came to operate more stably. A selective address was able to be discharged with four horizontal scanning electrodes from the experiment result. The operation margin of the AND gate discharge obtained 34V and of the address discharge obtained 70V.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.6
• /
• pp.569-577
• /
• 2015

The navigation algorithm developed based on the extended Kalman filter (EKF) sometimes diverges when the linearity between the measurements and the states is not preserved. In this study, new update conditions together with two conditions from previous study for gravity gradient referenced navigation (GGRN) were deduced for the filter performance. Also, the effect of each update conditions was evaluated imposing the various magnitudes of the database (DB) and the sensor errors. In case the DB and the sensor errors were supposed to 0.1 Eo and 0.01 Eo, the navigation performance was improved in the eight trajectories by using part of gravity gradient components that independently estimate states located within trust boundary. When applying only the components showing larger variation, around 200% of improvement was found. Even the DB and sensor error were supposed to 3 Eo, six update conditions improved performance in at least seven trajectories. More than five trajectories generated better results with 5 Eo error of the DB and the sensor. Especially, two update conditions successfully control divergence, and bounded the navigation error to the 1/10 level. However, these update conditions could not be generalized for all trajectories so that it is recommended to apply update conditions at the stage of planning, or as an index of precision of GGRN when combine with various types of geophysical data and algorithm.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.12-16
• /
• 2007

In this paper, The 3rd-IMD of class-F power amplifier is improved using CMRC structure in order to remove the parasitic End harmonic at the output load of class-F power amplifier. The total size is very small more than class-F power amplifier using PBG. (Photonicband Gap) structure during improved 3rd-IMD characteristic performance.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.399-404
• /
• 2014

A power amplifier (PA) for a femto-cell base station should be highly efficient, linear and small. The efficiency for amplification of a high peak-to-average power ratio (PAPR) signal was improved by designing an asymmetric Doherty PA (DPA). The linearity was improved by applying third-order inter-modulation (IM3) cancellation method. A small size is achieved by designing the DPA using GaN MMIC process. The implemented 2-stage DPA delivers a power-added efficiency (PAE) of 38.6% and a gain of 33.4 dB with an average power of 34.2 dBm for a 7.2 dB PAPR 10 MHz bandwidth LTE signal at 2.14 GHz.