• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.224-224
• /
• 2014

최근 기존의 아연 도금 강판의 성능을 향상시키기 위하여 다른 금속과의 합금 박막의 연구가 활발히 진행 중에 있다. 기존 아연 도금 강판에 비해 Mg를 함유한 Zn-Mg 합금 박막이 내식성이 우수하다고 알려져 있으며, 본 연구에서는 다양한 Mg 함량의 Zn-Mg 합금 타겟을 사용하여 Zn-Mg 박막을 합성하였다. 합성된 박막들의 내식성을 평가하기 위해서 Electrochemical Impedance Spectroscopy (EIS) 분석을 실시하였으며, 도출된 Nyquist plot 과 Bode phase angle plot 결과를 등가회로 피팅과 시뮬레이션을 실시하여 Mg 함량에 따른 Zn-Mg 박막의 내식성을 비교 분석하였다. Zn-Mg 박막은 Mg 함량이 증가할수록 내식성 또한 증가하였으며, 이는 Mg 함량에 따라 치밀해지는 미세구조에 의한 것으로 판단된다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.753-762
• /
• 1996

In this paper, aperture coupled stacked microstrip array antennas are proposed and their operating characteristics are analyzed based on analytical. In order to evaluate mutual coupling between slot-coupled microstrip patches in finite array, analysis uses the reciprocity theorem and the spectral domain Green's functions for dielectric slab in a moment method solution for the unknown patches and solts current distrbution. By introducing an N-port equivalent network, the impedance matrix of an affay of N-element slot-coupled patches is evaluated directly from its network current matix of order N$^{2}$, and it can be programmed to be run on a PC. Numerical results show mutual coupling, radiation pattern, active reflection coefficient versus scan angle, radiation efficiency and active element gain pattern.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.1
• /
• pp.9-17
• /
• 1970

The paper presents pole optimization in RC network of active RC filter using current inversion negative impedance converter. And also empais is placed on improving the stability of the active RC filter. Experimental results obtained with active RC low pass filter, having Chebyshev 2nd order response and modular angle 55$^{\circ}$, cutoff frequency 3.4KC, are shown and compared with theoretical curves.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.494-496
• /
• 2003

This paper analyses the operation characteristic of distance relay when the single line to ground occurs in underground power cable systems that reduction device of sheath circulating current is installed. To apply that reduction device to actual system, the change of line impedance calculated at relay point is also analysed by the connection type of SVLs and fault location, fault inception angle with the installation of reduction device of reactor or not.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.612-622
• /
• 2009

The short circuit ratio (SCR) of a given grid is able to show the stability of the system in the case of unwanted elements, such as wind turbulence. This paper presents the simulation of a model of the doubly fed induction generator in the simulation software PSCAD/EMTDC. This model has been used to study flicker during continuous operation and the effect of SCR and grid impedance angle on flicker emission. Simulation results show that compensation of the stator reactive power is an effective method to considerably reduce the flicker levels, irrespective of the grid conditions.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.53-61
• /
• 2006

In this paper, we present parametric studies for the optimum design of a hexagonal plate monopole antenna. The dependence of the antenna performance on various geometric parameters is investigated using a commercial electromagnetic software, from which an optimum design of a hexagonal plate monopole antenna is derived. Guidelines for determining initial parameter values are given. The diameter of the circular ground plane is minimized tlo 1/5 wavelength at the lowest operating frequency. The antenna impedance matching is controlled by adjusting the gap between the plate and the ground plane, the plate base width, and the base bevel angle. The antenna proposed in. this paper shows a reflection coefficient less than -10 dB and a $2.0{\sim}6.2$ dBi gain over $3{\sim}20$ GHz frequencies.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.5
• /
• pp.383-392
• /
• 2007

In this paper, we study the prediction of depth and width of a defect in steam generator tube in nuclear power plant using neural network. To this end, we first generate eddy current testing (ECT) signals for 4 defect patterns of SG tube: I-In type, I-Out type, V-In type, and V-Out type. In particular, we generate 400 ECT signals for various widths and depths for each defect type by the numerical analysis program based on finite element modeling. From those generated ECT signals, we extract new feature vectors for the prediction of defect size, which include the angle between the two points where the maximum impedance and half the maximum impedance are achieved. Using the extracted feature vector, multi-layer perceptron with one hidden layer is used to predict the size of defects. Through the computer simulation study, it is shown that the proposed method achieves decent prediction performance in terms of maximum error and mean absolute percentage error (MAPE).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.11
• /
• pp.2000-2006
• /
• 2011

Asynchronous phenomenon occurs on the synchronous generators under power system when a generator's amplitude of electromagnetic force, phase angle, frequency and waveform etc become different from those of other synchronous generators which can follow instantly varying speed of turbine. Because the amplitude of electromagnetic force, phase frequency and waveform differ from those of other generators with which are to be put into parallel operation due to the change of excitation condition for load sharing and the sharing load change, if reactive current in the internal circuit circulates among generators, the efficiency varies and the stator winding of generators are overheated by resistance loss. Where calculation method of protection settings and Logic for Protection of Generator Asynchronization will be recommended, A distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for graded zones having different operating time. As for the conventional step distance protection scheme, Zone 2 can exceed the ordinary coverage excessively in case of a transformer protection relay especially. In this case, there can be overlapped protection area from a backup protection relay and, therefore, malfunctions can occur when any fault occurs in the overlapped protection area. Distance relays and overcurrent relays are used for backup protection generally, and both relays have normally this problem, the maloperation, caused by a fault in the overlapped protection area. Corresponding to an IEEE standard, this problem can be solved with the modification of the operating time. On the other hand, in Korea, zones are modified to cope with this problem in some specific conditions. These two methods may not be obvious to handle this problem correctly because these methods, modifying the common rules, can cause another coordination problem. To overcome asynchronizing protection this paper describes an improved backup protection coordination scheme using a new Logic that will be suggested.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.6
• /
• pp.330-334
• /
• 2014

In this study, the Zn-Mg alloy coatings with various Mg contents were deposited using an unbalanced magnetron sputtering process. Their surface microstructure, chemical composition, phase, and corrosion property were investigated. The microstructure of the Zn-Mg coatings changed from porous microstructure to dense one with increasing Mg contents in the coatings. As Mg contents in coatings increased, intermetallic phases such as $Mg_2Zn_{11}$ and $MgZn_2$ were detected from X-ray diffraction (XRD) results. The corrosion resistance of the Zn-Mg alloy coatings was investigated quantitatively using electrochemical impedance spectroscopy (EIS) measurement with 3.5% NaCl solution. The results of EIS measurement showed that the charge transfer resistance and the phase angle of the Zn-Mg alloy coatings were increased from $162.1{\Omega}{\cdot}cm^2$ to $558.8{\Omega}{\cdot}cm^2$ and from about $40^{\circ}$ to $60^{\circ}$ with increasing Mg contents from 5.1 wt.% to 15.5 wt.% in the coatings. These results demonstrate that the Zn-Mg coatings with increasing Mg contents showed an enhanced corrosion resistance.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.498-505
• /
• 2020

Aggregate occupies about 70-85% of the concrete volume and is an important factor in reducing the drying shrinkage of concrete. However, when constructing high-rise buildings, it acts as a problem due to the high load of natural aggregates. If the load becomes large during the construction of a high-rise building, creep may occur and the ground may be eroded. Material costs increase and there are financial problems. In order to reduce the load on concrete, we are working to reduce the weight of aggregates. However, artificial lightweight aggregates affect the interface between the aggregate and the paste due to its higher absorption rate and lower adhesion strength than natural aggregates, affecting the overall strength of concrete. Therefore, in this study, in order to grasp the interface between natural aggregate and lightweight aggregate by type, we adopted a method of measuring electrical resistance using an EIS measuring device, which is a non-destructive test, and lightweight bone. The change in the state of the interface was tested on the outside of the material through a blast furnace slag coating. As a result of the experiment, it was confirmed that the electric resistance was about 90% lower than that in the air-dried state through the electrolyte immersion, and the electric resistance differs depending on the type of aggregate and the presence or absence of coating. As a result of the experiment, the difference in compressive strength depending on the type of aggregate and the presence or absence of coating was shown, and the difference in impedance value and phase angle for each type of lightweight aggregate was shown.