한국건설순환자원학회논문집 (Journal of the Korean Recycled Construction Resources Institute)

한국건설순환자원학회 (Korean Recycled Construction Resources Institute)
권호 표지
DOI QR코드

DOI QR Code

EIS를 활용한 경량골재 종류별 시멘트 경화체의 계면특성 분석

ITZ Analysis of Cement Matrix According to the Type of Lightweight Aggregate Using EIS

  • 김호진 (목원대학교 건축공학과) ;
  • 정용훈 (목원대학교 건축공학과) ;
  • 배제현 (충남대학교 분석과학기술대학원) ;
  • 박선규 (목원대학교 건축공학과)
  • Kim, Ho-Jin (Department of Architectural Engineering, Mokwon University) ;
  • Jung, Yoong-Hoon (Department of Architectural Engineering, Mokwon University) ;
  • Bae, Je-Hyun (Graduate School of Analytical Science and Technology, Chungnam National University) ;
  • Park, Sun-Gyu (Department of Architectural Engineering, Mokwon University)
  • 투고 : 2020.10.29
  • 심사 : 2020.11.13
  • 발행 : 2020.12.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

골재는 콘크리트 체적의 약 70~85%를 차지하며, 콘크리트의 건조수축을 저감시켜주는 필수요소이다. 하지만 고층건축물 건설시 천연골재의 높은 하중으로 인해 문제점으로 작용한다. 고층 건물 건설시 하중이 커지게 되면 크리프가 발생하고 지반이 침식될 우려가 있으므로 기초를 크게 설계하고 암반층까지 깊게 내린 지정이나 파일등을 설치해야 하므로 공사비 및 재료비가 늘어 경제적 문제점이 있다. 콘크리트의 하중을 줄이기 위해 골재의 경량화를 진행하고 있다. 하지만 인공경량골재는 천연 골재에 비해 높은 흡수율과 낮은 부착강도로 인해 골재와 페이스트 사이의 계면에 영향을 주고 콘크리트 전체 강도에 영향을 미친다. 따라서 본 연구에서는 천연골재와 경량골재 종류별 계면을 파악하기 위해 비파괴 실험인 EIS측정 장비를 활용하여 전기저항을 측정하는 방식을 채택하였고, 경량골재 겉면을 고로슬래그 코팅을 통해 계면상태의 변화를 실험하였다. 실험결과, 골재 종류별 및 코팅유무에 따른 압축강도의 차이를 보였고, 경량골재 종류별 임피던스 값과 위상각의 차이를 보였다.

Aggregate occupies about 70-85% of the concrete volume and is an important factor in reducing the drying shrinkage of concrete. However, when constructing high-rise buildings, it acts as a problem due to the high load of natural aggregates. If the load becomes large during the construction of a high-rise building, creep may occur and the ground may be eroded. Material costs increase and there are financial problems. In order to reduce the load on concrete, we are working to reduce the weight of aggregates. However, artificial lightweight aggregates affect the interface between the aggregate and the paste due to its higher absorption rate and lower adhesion strength than natural aggregates, affecting the overall strength of concrete. Therefore, in this study, in order to grasp the interface between natural aggregate and lightweight aggregate by type, we adopted a method of measuring electrical resistance using an EIS measuring device, which is a non-destructive test, and lightweight bone. The change in the state of the interface was tested on the outside of the material through a blast furnace slag coating. As a result of the experiment, it was confirmed that the electric resistance was about 90% lower than that in the air-dried state through the electrolyte immersion, and the electric resistance differs depending on the type of aggregate and the presence or absence of coating. As a result of the experiment, the difference in compressive strength depending on the type of aggregate and the presence or absence of coating was shown, and the difference in impedance value and phase angle for each type of lightweight aggregate was shown.

키워드

참고문헌

  1. Choi, H.I., Choi, J.H., Lee, D.I., Wie, W.B., Kim, T.Y., Min, B.W., Baek, S.D. (2006). A characteristic of AC impedance for property assessment of paints on transmission towers, The Korean Institute of Electrical Engineers, 492-493.
  2. Guilan, T., Congcong, G., Zhaoyang, Q. (2017). Electrochemical Impedance spectroscopy study of the compressive strength of concrete, International Journal of Electrochemical Science, 12, 11692-11700.
  3. Kang, S.H., Hong, S.G. (2015). Effect of surface preparation and curing condition on the interfacial bond strength between ultra high performance concrete and normal strength concrete, Journal of the Korea Institute for Structural Maintenance and Inspection, 19(3), 149-160 [in Korean]. https://doi.org/10.11112/jksmi.2015.19.3.149
  4. Kang, T.H., Cho, W.I., Cho, B.W., Ju, J.B., Yun, K.S. (1998). Studies on the concrete reinforcement corrosion by electrochemical impedance spectroscopy, Applied Chemistry for Engineering, 9(6), 907-913 [in Korean].
  5. Kim, S.C., Park, K.G., Choi, H.W. (2011). An experimental study for the strength variations of high-strength lightweight concrete according to grain-size of artificial lightweight aggregate, Magazine of the Korea Institute for Structural Maintenance and Inspection, 15(5), 209-2017 [in Korean].
  6. Kim, Y.T., Jang, C.S., Ryu, Y.W. (2011). Water absorption characteristics of artificial lightweight aggregate pre-pared by pre-wetting. Journal of the Korean Crystal Growth and Crystal Technology, 21(2), 82-86 [in Korean]. https://doi.org/10.6111/JKCGCT.2011.21.2.082
  7. Kong, L., Hou, L., Wang, Y., Sun, G. (2016). Investigation of the interfacial transition zone between aggregate-cement paste by AC impedance spectroscopy, Journal of Wuhan University of Technology-Mater. Sci. Ed., 31(4), 865-871 [in Korean]. https://doi.org/10.1007/s11595-016-1460-2
  8. Park, D.O., Sa, S.H., Ji, S.W., Choi, S.K., Yoo, T.D., Seo, C.H. (2007). Study on characteristics of lightweight aggregate concrete as types of lightweight aggregate, Proceedings of the Korean Institute of Building Construction Conference, 7(1), 67-70 [in Korean].
  9. Park, J.H., Lee, H.S. (2017). An experimental study of the corrosion behavior evaluation of revar in concrete by using electrochemical impedance spectroscopy(EIS) method, Journal of the Korea Institute for Structural Maintenance and Inspection, 21(1), 083-090 [in Korean].
  10. Park, S.M. (1999). Electrochemical impedance spectroscopy, Polymer Science and Technology, 10(6), 817-829 [in Korean].
  11. Ryu, J.C., Lee, M.E. (2019). Development of high precision impedance measurement system in specific ranges using a microprocessor, Journal of Advanced Navigation Technology, 23(4), 316-321 [in Korean].
  12. Sim, J.I., Yang, K.H. (2012). Influence of specimen geometries on the compressive strength of lightweight aggregate concrete, Journal of the Korea Concrete Institute, 24(3), 333-340 [in Korean]. https://doi.org/10.4334/JKCI.2012.24.3.333
  13. Vargas, P., Restrepo-Baena, O., Tobon, J.I. (2017). Microstructural analysis of interfacial transition zone (ITZ) and its impact on the compressive strength of lightweight concretes, Construction and Building Materials, 137, 381-389. https://doi.org/10.1016/j.conbuildmat.2017.01.101
  14. Yang, K.H. (2019). Evaluation of mechanical properties of lightweight concrete using bottom ash aggregates, Journal of the Korea Concrete Institute, 31(4), 331-337 [in Korean]. https://doi.org/10.4334/jkci.2019.31.4.331