• 대한기계학회논문집A
• /
• 제40권2호
• /
• pp.185-198
• /
• 2016

본 논문에서는 통계적인 기법을 기반으로 유한 요소 모델을 개선하기 위해 수행되는 임팩트 해머 실험에서 발생할 수 있는 오차 요인을 분석하고, 오차를 줄일 수 있는 방안을 제시한다. 먼저, 이론 모델과 실험을 통해, 실험 과정과 측정된 신호를 후처리 하는 과정에서 발생할 수 있는 오차 요인을 파악한다. 실험 오차 요인으로 가진력의 지속 시간과 크기, 시편을 지지대와 연결하는 고무줄의 강성과 위치, 응답 신호를 측정하기 위해 시편에 부착하는 가속도계의 위치와 질량을 고려하고, 이에 따른 고유 모드와 고유 주파수의 변화를 살펴본다. 그리고, 디지털 신호 처리 과정에서는 말뚝 울타리 효과, 누설, 지수창 함수 사용에 의한 오차를 살펴보고, 이런 오차를 줄일 수 있는 방법을 제시한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1078-1081
• /
• 2004

A robot manipulator is usually operated in two modes: free motion and constraint motion depending on whether the robot comes into contact with the environment or not. At the moment of contact, impact occurs, and sometimes, it possibly degrade the robot's performance by vibration and at worst, shortens its lifetime. In this article, a new proposed algorithm is described by introducing a command signal modification method on the basis of impedance control and a validity of the proposed algorithm is demonstrated by showing a simulation and an experiment.

• 융합신호처리학회 학술대회논문집
• /
• 한국신호처리시스템학회 2000년도 하계종합학술대회논문집
• /
• pp.13-16
• /
• 2000

Since stimulated Brillouin scattering (SBS) impact wavelength division multiplexing (WDM) optical transmission systems, it is important to understand the implication of SBS in the design of such lightwave systems. Therefore, Brillouin gain spectrum (BGS) is measured to characterize the effect of SBS in optical fiber. The Brillouin gain coefficient is found to vary as the wavelength and linewidth of source. Theoretically measurement of BGS shows a dependence on wavelength(λ) and on linewidth(Δν), respectively.

• Journal of Astronomy and Space Sciences
• /
• 제28권4호
• /
• pp.267-271
• /
• 2011

I developed an enhanced correction method for Ricean bias which occurs in linear polarization measurement. Two known methods for Ricean bias correction are reviewed. In low signal-to-noise area, the method based on the mode of the equation gives better representation of the fractional polarization. But a caution should be given that the accurate estimation of noise level, i.e. ${\sigma}$ of the polarized flux, is important. The maximum likelihood method is better choice for high signal-to-noise area. I suggest a hybrid method which uses the mode of the equation at the low signal-to-noise area and takes the maximum likelihood method at the high signal-to-noise area. A modified correction coefficient for the mode solution is proposed. The impact on the depolarization measure analysis is discussed.

• Transactions on Electrical and Electronic Materials
• /
• 제10권6호
• /
• pp.212-216
• /
• 2009

The spatial distribution of the optogalvanic (OG) signal in argon at the 801.489 nm ($1s_5-2p_8$ transition at the metastable level in Paschen notation) was investigated in the radial direction of a hollow cathode discharge tube. The results of this experiment showed that the OG signal amplitude decreases in accordance with the following two conditions; first, the level of discharge current and second, the distance from the cathode dark space. These results can be quantified by analyzing the electron density profile along the discharge regions, which can directly influence the collisional ionization induced by electron impact.

• 한국통신학회논문지
• /
• 제38C권11호
• /
• pp.1044-1050
• /
• 2013

본 논문은 ETRI에서 개발한 GPS RF 신호생성기와 상용수신기인 U-Blox 수신기를 이용하여 기만신호의 공격을 완화하는 방법에 대하여 분석하였다. 기만신호는 대상 수신기의 코드 및 반송파 성분의 변이를 이용하여 대상수신기가 비정상적인 위치를 생성하도록 하는 것이다. 우리는 이러한 기만신호 공격에 따른 수신기에서의 신호세기 및 항법해 영향을 분석하였다. 또한 기만신호를 제거하기 위하여 기만신호와 역위상 코드를 가지는 신호를 고려하였다. GPS RF 신호생성기를 이용하여 정상적인 GPS 신호, 기만신호, 기만신호와 역위상을 가지는 항기만신호를 생성하였고 기만신호와 항기만신호간의 코드 위상차이에 따른 기만신호 공격의 영향을 수신기를 통하여 확인하였다. 기만 신호의 코드 지연과 동일한 코드지연의 신호를 생성할 경우 기만신호가 상쇄되는 것을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.885-890
• /
• 2007

Fast Fourier Transformation(FFT) is one of the most useful way to analyze response signal for the purpose of grasping the dynamic characteristics of system. Vibration test using impact hammer is typical and simple experimental method widely used for catching hold of dynamic peculiar characters and modal behaviors of system. In this thesis, impact testing module for NI-PXI equipment is developed. The analyzing and visualizing module are developed with LabVIEW tool. A user can see quickly and easily modal shape of system after analyzing acquired data. This developed module will be expected to build up more convenient and serviceable measurement system.

• 한국안전학회지
• /
• 제13권2호
• /
• pp.3-12
• /
• 1998

Polymer materials have been used offensively as construction materials for automobiles, ships, and airplanes in recent years, and their impact resistance has been obliged to be examined. In the present study, a dropped load and a specimen, equipped with high responsible strain gauges respectively, were dropped and then the changes of load and absorption energy with time were observed. It was found that the waveforms for dropped weight coincided with output signal wave for specimen during the destruction test. Based on this experimental result, three disc type of specimens with different compositions were prepared and examined. This instrumented impact test method showed that each specimen can be distinguished from each other better than conventional tests and is expected to contribute to assess test results of impact resistance for some materials under development.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2509-2512
• /
• 2005

In this paper, a position control scheme of the ink droplet is presented for the high image quality and print speed inkjet printer. The proposed scheme estimates the impact position and compensates it by control of the fire strobe time based on the dynamic equations describing the moving trajectory of the ink droplet. Compared to the conventional fire strobe control which is based on the simple synchronization the fire strobe with the position signal of the inkjet nozzle, the proposed control scheme provides more accurate impact position control during the carrier is moving with accelerated or decelerated speed as well as constant speed. The availability of printing during the acceleration and deceleration states of the carrier moving enables the print speed up and the frame size down which means the cost down.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.594-601
• /
• 2016

Mass estimation analysis of loose-parts in pressure vessel is necessary for the structural integrity assessment of pressure boundary in nuclear power plants. Mass of loose-parts can be generally estimated from the peak values and the center frequency of impact signals. Magnitude of impact signals is, however, inevitably attenuated according to the traveling distance of the signals and depending on the frequencies. Attenuation rate must be therefore carefully compensated for the precise estimation of loose-part mass. This paper proposes a new compensation method for the attenuation rate based on Bessel function instead of Hankel function in conventional method which has a limitation of usage in near the impact location. It was verified that the suggested compensating equation based on the Bessel function can be applied to the attenuation rate calculation without any limitation.