• Current Photovoltaic Research
• /
• v.10 no.1
• /
• pp.28-32
• /
• 2022

We investigated the optical and electrical characteristics of ITO/Ag/ITO (IAI) 3-layer thin films prepared by using RF/DC sputtering. To measure the thickness of all thin film samples, we used scanning electron microscopy. As a function of Ag thickness we characterized the optical transmittance and sheet resistance of the IAI samples by using UV-Visible spectroscopy and Hall measurement system, respectively. While the thickness of both ITO thin films in the 3-layered IAI samples were fixed at 50 nm, we varied Ag layer thickness in the range of 0 nm to 11 nm. The optical transmittance and sheet resistance of the 3-layered IAI thin films were found to vary strongly with the thickness of Ag film in the ITO (50 nm)/Ag(t₀)/ITO (50 nm) thin film. For the best transparent conducting oxide (TCO) electrode, we obtained a 3-layered ITO (50 nm)/Ag (t₀ = 8.5 nm)/ITO (50 nm) that showed an avrage optical transmittance, AVT = 90.12% in the visible light region of 380 nm to 780 nm and the sheet resistance, R_□ = 7.24 Ω/□.

• Journal of Sensor Science and Technology
• /
• v.16 no.3
• /
• pp.229-233
• /
• 2007

The indium tin oxide (ITO) films were deposited on CR39 substrate using DC magnetron sputtering. The ITO thin films deposited at room temperature because CR39 substrate its glass-transition temperature is $130^{\circ}C$. The ITO thin films used bottom and top electrode and for organic thin film transparent transistors (OTFTs). The ITO thin film electrodes electrical properties and optical transparency properties in the visible wavelength range (300-800 nm) strongly dependent on volume of oxygen percent. For the optimum resistivity and transparency of the ITO thin film electrode achieved with a 75 W plasma power, 10 % volume of oxygen and a 27 nm/min deposition rate. Above 85 % transparency in the visible wavelength range (300-800 nm) measured without post annealing process and a low resistivity value $9.83{\times}10^{-4}{\Omega}cm$ was measured thickness of 300 nm. All fabrication process of ITO thin films did not exceed $80^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.307-308
• /
• 2009

We have proposed an index matching film to improve the emitting efficiency of green OLED. Here, SiO2 and TiO2 were selected to coat the green OLED. The structures of index matching film were designed in G1ass/TiO2/SiO2/ITO and SiO2/TiO2/Glass/ITO. Then, these materials were deposited by ion-assisted deposition system. Transmittances of deposited devices were 86.14 and 85.07 %, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.1
• /
• pp.21-25
• /
• 2009

Using an evaporation system, $SiO_2$ was deposited as a buffer layer between a PET substrate and a ITO layer and then ITO/$SiO_2$/PET layers were annealed for 1.5 hours at the temperature of $180^{\circ}C$. Adhesion and electro-optical properties of ITO films were studied with thickness variance of a $SiO_2$ buffer layer. As a result of introduction of the $SiO_2$ buffer layer, sheet resistance and resistivity increased and a ITO film with optimum sheet resistance ($529.3{\Omega}/square$) for an upper ITO film of resistive type touch panel could be obtained when $SiO_2$ of $50{\AA}$ was deposited. And it was found that ITO films with $SiO_2$ buffer layer have higher transmittance of $88{\sim}90%$ at 550 nm wavelength than ITO films with no buffer layers and the transmittance was enhanced as $SiO_2$ thickness increased from $50{\AA}$ to $100{\AA}$. Adhesion property of ITO films with $SiO_2$ buffer layers became better than ITO films with no buffer layers and this property was independent of $SiO_2$ thickness variance ($50{\sim}100{\AA}$). By depositing a $SiO_2$ buffer layer of $50{\AA}$ on the PET substrate and sputtering a ITO thin film on the layer, a ITO film with enhanced adhesion, electro-optical properties could be obtained.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.2
• /
• pp.55-59
• /
• 2005

ITO/Ni/ITO thin films were deposited on the PET by RF magnetron sputtering. Dependance of the process parameters such as deposition pressure, positions of Ni layer, on the transmittance, reflectance and sheet resistance of ITO/Ni/ITO film were investigated. When the Ni layer is placed at the center of ITO and deposition pressure is low, ITO/Ni/ITO films showed better optical and electrical properties. At these conditions, the transmittance, reflectance and sheet resistance of the ITO film were $90\%,\;0.38\%$ and $185\Omega/\Box$ respectively.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.62-64
• /
• 2005

Indium Tim Oxide(ITO) thin film was prepared for TOLEDs by Facing Targets Sputtering(FTS) apparatus which can suppress the damage of organic layer due to the collisions of high energetic particles. In particular, ITO thin film was prepared with changing the distance between two targets for reduced the bombardment by high energetic particles such as ${\gamma}-electron$ or negative oxygen ions. The electrical and optical properties of ITO thin films as a function of distance of between two targets were measured. Additionally, the ITO thin films were prepared on the cell (cell : MgAg/LiF/EML/HTL/ bottom electrode) with distance of between two targets. And the I-V characteristics of ITO/cell was investigated.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.3
• /
• pp.158-163
• /
• 2004

ITO thin film was deposited on the glass by RF magnetron sputtering. Dependance of the process parameters such as thickness, target-to-substrate distance, substrate temperature and oxygen partial pressure on the transmittance and electrical resistance of ITO film were investigated. The deposition conditions for getting better optical and electrical ITO characteristics were the 1800-$2300\AA$ thickness, 65mm substrate-to-target distance, $350^{\circ}C$ substrate temperature and 8% oxygen partial pressure. At these conditions, the transmittance and sheet resistance of the ITO film were 83.3% and 77.86Ω/$\square$, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.510-514
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD(Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn 10wt%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature 15$0^{\circ}C$ and 8% $O_2$. Partial pressure showed about 3.6 Ω/$\square$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.

• Laser Solutions
• /
• v.13 no.1
• /
• pp.11-15
• /
• 2010

Indium tin oxide (ITO) provides high electrical conductivity and transparency in the visible and near IR (infrared) wavelengths. Thus, it is widely used as a transparent electrode for the fabrication of liquid crystal displays (LCDs) and organic light emitting diode displays (OLRDs), photovoltaic devices, and other optical applications. Lasers have been used for removing coating on polymer substrate for flexible display and electronic industry. In selective removal of ITO layer, laser wavelength, pulse energy, scan speed, and the repetition rate of pulses determine conditions, which are efficient for removal of ITO coating without affecting properties of the polymer substrate. ITO coating removal with a laser is more environmentally friendly than other conventional etching methods. In this paper, pattering of ITO film from polymer substrates is described. The Yb:KGW femtosecond laser processing system with a pulse duration of 250fs, a wavelength of 1030nm and a repetition rate of 100kHz was used for removing ITO coating in air. We can remove the ITO coating using a scanner system with various pulse energies and scan speeds. We observed that the amount of debris is minimal through an optical and a confocal microscope, and femtosecond laser pulses with 1030nm wavelength are effective to remove ITO coating without the polymer substrate ablation.

• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.1-6
• /
• 2009

In this study, the stress-strain response and the cracking behaviors of ITO film on a PET substrate are investigated. The cracking behaviors of ITO thin films deposited on a thermoplastic semi-crystalline polymer developed for flexible display applications was investigated by means of tensile experiments equipped with an electrical measurement apparatus and an in-situ optical microscope. Electrical resistance increased gradually in the elastic-to-plastic transition region of the stress strain curves and cracks formed. Numerous cracks were found in this region, and the increase of the resistance was linked to the cracking of ITO thin films. Upon loading, the initial cracks perpendicular to the tensile axis were observed at about 1% of the total strain. They propagated to the entire sample width as the strain increased. The spacing between the horizontal cracks is thought to be determined by the fracture strength and the thickness of the ITO film as well as by the interfacial strength between the ITO and PET. The effect of the strain rate on the cracking behavior was also investigated. The crack density increased as the strain increased. The spacing between the horizontal cracks (perpendicular to the stress axis) increased as the strain rate decreased. The increase of the crack density as the strain rate decreased can be attributed to the higher fraction of the plastic strain to the total strain at a given total strain. The higher critical strain for the onset of the increase in the resistance and the crack initiation of the ITO/PET with a thinner ITO film (300 ohms/sq.) suggests a higher strength of the thinner ITO film.