• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제14권4호
• /
• pp.935-938
• /
• 2010

Indium-tin-oxide (ITO) films show a low electrical resistance and high transmittance in the visible range of an optical spectrum. The transparent electrodes have to get resistivity and sheet resistance less than $1{\times}10^{-3}{\Omega}/cm$ and $10^3{\Omega}/sq$ respectively and transmittance over 80% at wavelength of 380nm~780nm. This study establishes DC magnetron sputtering process condition on ITO thin film by measuring electrical and optical properties of the thin film. As results, we obtained $300\;{\mu}{\Omega}cm$ resistivity of ITO films with good transmittance (above 90 %) under 90:10 wt% composition rate of $In_2O_3:SnO_2$. Also, we understood that the ITO thin film by DC magnetron sputtering depends on the deposition condition, especially substrate temperature, and the composition rate of $In_2O_3:SnO_2$ that is one of the most critical parameters was successfully optimized for high qualified transparent electrodes.

• Journal of the Korean institute of surface engineering
• /
• 제45권6호
• /
• pp.242-247
• /
• 2012

Yb-doped ITO (ITO:Yb) films were deposited on unheated non-alkali glass substrates by magnetron cosputtering using two cathodes (DC, RF) equipped with the ITO and $Yb_2O_3$ target, respectively. The composition of the ITO:Yb films was controlled by adjusting the RF powers from 0 W to 480 W in 120 W steps with the DC power fixed at 70 W. The ITO:Yb films had a higher crystallization temperature ($200^{\circ}C$) than that of the ITO films ($170^{\circ}C$), which was attributed to both larger ionic radius of $Yb^{3+}$ and higher bond enthalpy of $Yb_2O_3$, compared to ITO. This amorphous ITO:Yb film post-annealed at $170^{\circ}C$ showed a resistivity of $5.52{\times}10^{-4}{\Omega}cm$, indicating that a introduction of Yb increased resistivity of the ITO film. However, these amorphous ITO:Yb films showed a high etching rate, fine pattering property, and a very smooth surface morphology above the crystallization temperature of the amorphous ITO films (about $170^{\circ}C$). The transmittance of all films was >80% in the visible region.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 한국반도체및디스플레이장비학회 2006년도 추계학술대회 발표 논문집
• /
• pp.51-55
• /
• 2006

ITO/Ag/AZO and AZ0/Ag/ITO multi-layer films deposited on glass substrate by RF magnetron sputtering have a much better electrical properties than ITO and AZO single-layer films. The multi-layer structure was consisted of three layers of ITO, Ag and AZO. The optimum working pressure of AZO layers deposition was determined to be $1.0{\times}10^{-2}$ torr for high optical transmittance and good electrical conductivity. The electrical and optical properties of sub/IT0/Ag/AZO were higher than those of sub/AZ0/Ag/ITO multi-layer films.

• Journal of the Korean institute of surface engineering
• /
• 제37권3호
• /
• pp.158-163
• /
• 2004

ITO thin film was deposited on the glass by RF magnetron sputtering. Dependance of the process parameters such as thickness, target-to-substrate distance, substrate temperature and oxygen partial pressure on the transmittance and electrical resistance of ITO film were investigated. The deposition conditions for getting better optical and electrical ITO characteristics were the 1800-$2300\AA$ thickness, 65mm substrate-to-target distance, $350^{\circ}C$ substrate temperature and 8% oxygen partial pressure. At these conditions, the transmittance and sheet resistance of the ITO film were 83.3% and 77.86Ω/$\square$, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.510-514
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD(Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn 10wt%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature 15$0^{\circ}C$ and 8% $O_2$. Partial pressure showed about 3.6 Ω/$\square$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.203-206
• /
• 2004

In this study the ITO thin films were prepared by using FTS(Facing Targets Sputtering) system. The electric characteristics, transmittance, surface roughness of ITO thin films were investigated as a function of varying input current and working gas pressure at room temperature. As a result, the ITO thin film was fabricated with resistivity $6{\times}10^{-4}[\Omega{\cdot}cm]$, carrier mobility $52.11[cm^2/V{\cdot}sec]$, carrier concentration $1.72{\times}10^{20}[cm^{-3}]$ of ITO thin film at working pressure 1mTorr and input current 0.6A.

• Current Photovoltaic Research
• /
• 제10권1호
• /
• pp.28-32
• /
• 2022

We investigated the optical and electrical characteristics of ITO/Ag/ITO (IAI) 3-layer thin films prepared by using RF/DC sputtering. To measure the thickness of all thin film samples, we used scanning electron microscopy. As a function of Ag thickness we characterized the optical transmittance and sheet resistance of the IAI samples by using UV-Visible spectroscopy and Hall measurement system, respectively. While the thickness of both ITO thin films in the 3-layered IAI samples were fixed at 50 nm, we varied Ag layer thickness in the range of 0 nm to 11 nm. The optical transmittance and sheet resistance of the 3-layered IAI thin films were found to vary strongly with the thickness of Ag film in the ITO (50 nm)/Ag(t₀)/ITO (50 nm) thin film. For the best transparent conducting oxide (TCO) electrode, we obtained a 3-layered ITO (50 nm)/Ag (t₀ = 8.5 nm)/ITO (50 nm) that showed an avrage optical transmittance, AVT = 90.12% in the visible light region of 380 nm to 780 nm and the sheet resistance, R_□ = 7.24 Ω/□.

• Journal of Information Display
• /
• 제9권4호
• /
• pp.15-20
• /
• 2008

A DC-magnetron inline sputter was established, and the influence of the base pressure on the structural characteristics of the ITO thin films was studied. When the inline sputter system was established and operated for ITO sputtering, its initial vacuum level did not go below $5\times10^{-6}$ torr. The vacuum leak test was conducted by measuring t he elapsed time until the vacuum level reached $1\times10^{-6}$ torr. The base pressure was successfully maintained at $1\times10^{-6}$ torr for 900 min, and the uniformity of the ITO film that had been deposited at this pressure significantly improved.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.254-257
• /
• 2008

We have investigated the effect of source/drain electrode deposition method on a performance of top gate structured ZnO TFT performance. TFT using S/D of ITO film, consisted of bi-layer which deposited by ion beam assisted sputtering at the initial stage then deposited by DC magnetron sputtering, showed better performance compared to that using S/D of ITO deposited by just DC magnetron sputtering. Two ITO films exhibited different grain shapes and these resulted in different etching properties. We also suspect that charge trapping on the glass substrate (back channel) during the ITO film deposition may influence the characteristics of top gate structured ZnO TFT.

• Journal of the Korean Ceramic Society
• /
• 제38권11호
• /
• pp.973-979
• /
• 2001

Tin-doped indium oxide (ITO) thin films were deposited using r.f. magnetron reactive sputtering and the electrical properties, such as the resistivity, carrier concentration and mobility, were investigated as a function of the sample position under a given magnetron sputtering condition. The nonhomogeneity of the electrical properties with the sample position was observed under a given magnetron sputtering condition. The resistivity of ITO thin film on the substrate which corresponded to the center of the target had a minimum value, 2∼4$\times$10$\^$-4/$\Omega$$.$cm, and it increased symmetrically when the substrate deviated from the center. The density measurement result also showed that ITO thin film deposited at the center has a maximum density of 7.0g/cm$^3$, which was a relative density of about 97%, and the density decreased symmetrically as the substrate deviated from the center. The nonhomogeneity of electrical properties with the deposition position could be explained with the incidence angle of the source beam alpha, which is related with an atomic self-shadowing effect. It was confirmed experimentally that the density in film affect both the carrier mobility and the conductivity. In the case where the density of ITO thin film is 7.0g/cm$^3$, the magnitude of the mean free path was identical with that of the grain size(the diameter of column). However, in the other cases, the mean free path was smaller than the grain size. These results showed that the scattering of the free electrons at the grain boundary is the major factor for the electrical conduction in ITO thin films having a high density, and there exists other scattering sources such as vacancies, holes, or pores in ITO thin films having a low density.ing a low density.