• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.282-285
• /
• 2000

Four helical resonators are distributed in a 2 ${\times}$ 2 array by modifying upper part of the conventional reactive ion etching(RIE) type LCD etcher in order to prepare a large area plasma source. Since the resonance condition of the RF signal to the helical antenna, one RF power supply is used for delivering the power efficiently to all four helical resonators without an impedance matching network Previous work of 2 ${\times}$ 2array inductively coupled plasma(ICP)requires one matching circuit to each ICP antenna for more efficient power deliverly Distributions of ion density and electron temperature are measured in terms of chamber pressure, gas flow rate and RF power . By adjusting the power distribution among the four helical resonator units, argon plasma density of higher than 10$\^$17/㎥ with the uniformity of better than 7％ can be obtained in the 620 ${\times}$ 620$\textrm{mm}^2$ chamber.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.244-250
• /
• 2008

An inductively coupled plasma etching process to replace an existing slower rate reactive ion etching process for $60{\mu}m$ diameter via-holes using Cl2/BCl3 gases has been investigated. Process pressure and platen power were varied at a constant ICP coil power to reproduce the RIE etched $200{\mu}m$ deep via profile, at high etch rate. Desired etch profile was obtained at 40 m Torr pressure, 950 W coil power, 90W platen power with an etch rate ${\sim}4{\mu}m$/min and via etch yield >90% over a 3-inch wafer, using $24{\mu}m$ thick photoresist mask. The etch uniformity and reproducibility obtained for the process were better than 4%. The metallized via-hole dc resistance measured was ${\sim}0.5{\Omega}$ and via inductance value measured was $\sim$83 pH.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.1
• /
• pp.84-93
• /
• 2001

An electromagnetic micro x-y stage for probe-based data storage (PDS) has been fabricated. The x-y stage consists of a silicon body inside which planar copper coils are embedded, a glass substrate bonded to the silicon body, and eight permanent magnets. The dimensions of flexures and copper coils were determined to yield $100{\;}\mu\textrm{m}$ in x and y directions under 50 mA of supplied current and to have 440 Hz of natural frequency. For the application to PDS devices, electromagnetic stage should have flat top surface for the prevention of its interference with multi-probe array, and have coils with low resistance for low power consumption. In order to satisfy these design criteria, conducting planar copper coils have been electroplated within silicon trenches which have high aspect ratio ($5{\;}\mu\textrm{m}$in width and $30{\;}\mu\textrm{m}$in depth). Silicon flexures with a height of $250{\;}\mu\textrm{m}$ were fabricated by using inductively coupled plasma reactive ion etching (ICP-RIE). The characteristics of a fabricated electromagnetic stage were measured by using laser doppler vibrometer (LDV) and dynamic signal analyzer (DSA). The DC gain was $0.16{\;}\mu\textrm{m}/mA$ and the maximum displacement was $42{\;}\mu\textrm{m}$ at a current of 180 mA. The measured natural frequency of the lowest mode was 325 Hz. Compared with the designed values, the lower natural frequency and DC gain of the fabricated device are due to the reverse-tapered ICP-RIE process and the incomplete assembly of the upper-sided permanent magnets for LDV measurements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.62-62
• /
• 2015

In this study, we study the effects of CF4 plasma treatment on the characteristics of enhancement mode (E-mode) AlGaN/GaN high electron mobility transistors (HEMTs). The CF4 plasma is generated by inductively coupled plasma reactive ion etching (ICP-RIE) system. The CF4 gas is decomposed into fluorine ions by ICP-RIE and then fluorine ions will effect the AlGaN/GaN interface to inhibit the electron transport of two dimension electron gas (2DEG) and increase channel resistance. The CF4 plasma method neither like the recessed type which have to utilize Cl2/BCl3 to etch semiconductor layer nor ion implantation needed high power to implant ions into semiconductor. Both of techniques will cause semiconductor damage. In the experiment, the CF4 treatment time are 0, 50, 100, 150, 200 and 250 seconds. It was found that the devices treated 100 seconds showed best electric performance. In order to prove fluorine ions existing and CF4 plasma treatment not etch epitaxial layer, the secondary ion mass spectrometer confirmed fluorine ions truly existing in the sample which treatment time 100 seconds. Moreover, transmission electron microscopy showed that the sample treated time 100 seconds did not have etch phenomena. Atomic layer deposition is used to grow Al2O3 with thickness 10, 20, 30 and 40 nm. In electrical measurement, the device that deposited 20-nm-thickness Al2O3 showed excellent current ability, the forward saturation current of 210 mA/mm, transconductance (gm) of 44.1 mS/mm and threshold voltage of 2.28 V, ION/IOFF reach to 108. As IV concerning the breakdown voltage measurement, all kinds of samples can reach to 1450 V.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.171-171
• /
• 2012

In this study, we fabricated the high-brightness AlGaInP-based red light emitting diodes (LED)s using by direct printing technique and inductive coupled plasma (ICP) reactive ion etching (RIE). In general, surface roughening was fabricated by wet etching process to improve the light extraction efficiency of AlGaInP-based red LED. However, a structure of the surface roughening, which was fabricated by wet etching, was tiled cone-shape after wet etching process due to crystal structure of AlGaInP materials, which was used as top-layer of red LED. This tilted cone-shape of surface roughening can improve the light extraction of LED, but it caused a loss of the light extraction efficiency of LED. So, in this study, we fabricated perfectly cone shaped pattern using direct printing and dry etching process to maximize the light extraction efficiency of LED. Both submicron pattern and micron pattern was formed on the surface of red LED to compare the enhancement effect of light extraction efficiency of LEDs according to the diameter of sapphire patterns.After patterning process using direct printing and ICP-RIE proceeded on the red LED, light output was enhanced up to 10 % than that of red LED with wet etched structure. This enhancement of light extraction of red LED was maintained after packaging process. And as a result of analyze of current-voltage characteristic, there is no electrical degradation of LED.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.162-163
• /
• 2008

이 논문에서는 Polyimide 기판의 $O_2$ 플라즈마 처리효과에 따른 GZO 박막의 구조적, 전기적, 광학적인 특성을 고찰하였다. ICP-RIE 방법을 이용하여 Polyimide 기판의 $O_2$ 플라즈마 처리의 변수로 RF power와 처리시간을 각 100 ~ 400 W, 120 ~ 600 초까지 조절하였다. RF 스퍼터링 방법으로 $O_2$ 플라즈마 처리효과에 따른 Polyimide 기판을 4인치의 GZO(ZnO : 95 wt%, $Ga_2O_3$ 5 wt%) 타겟을 사용하여 RF power 90 W, 공정압력 5 mTorr, Ar gas 20 sccm, 기판거리 5 cm, 박막두께 500nm, 상온의 조건으로 GZO 박막을 증착 하였다. Polyimide 기판에 $O_2$ 플라즈마 처리를 하지 않고 증착한 GZO 박막의 비저황은 $1.02\times10^{-2}\Omega$-cm 이었고 RF power 100W, 처리시간 120 초로 $O_2$ 플라즈마 처리 후에 증착한 GZO 박막의 비저항이 $1.89\times10^{-3}\Omega$-cm인 최적의 값이 측정되었으며 RF power가 증가할수록 투과도는 감소하였지만 처리시간의 변화에 따라서는 투과도 변화가 거의 없었다.

• Korean Journal of Materials Research
• /
• v.13 no.12
• /
• pp.775-778
• /
• 2003

We studied InP etching in high density planar inductively coupled $BCl_3$and $BCl_3$/Ar plasmas(PICP). The investigated process parameters were PICP source power, RIE chuck power, chamber pressure and $BCl_3$/Ar gas composition. It was found that increase of PICP source power and RIE chuck power increased etch rate of InP, while that of chamber pressure decreased etch rate. Etched InP surface was clean and smooth (RMS roughness <2 nm) with a moderate etch rate (300-500 $\AA$/min) after the planar $BCl_3$/Ar ICP etching. It may make it possible to open a new regime of InP etching with $CH_4$$H_2$-free plasma chemistry. Some amount of Ar addition (<50%) also improved etch rates of InP, while too much Ar addition reduced etch rates of InP.

• Journal of the Korean Vacuum Society
• /
• v.7 no.2
• /
• pp.161-168
• /
• 1998

Reactive ion etching process for InGaAs/InP using the CH4/H2 high density inductively coupled plasma was investigated. The experimental design method proposed by Taguchi was utilized to cover the whole parameter range while maintaining reasonable number of actual experiments. Results showed that the ICP power mainly affects surface roughness and verticality of the sidewall, bias power does etch rate and verticality, CH4 gas concentraion does the verticality and etch rate, and the distance between the induction coil and specimen mostly affects the surface roughness. It was also observed that the chamber pressure is the dominant parameter for the etch rate and verticality of the sidewall. The optimum condition was ICP power 700W, bias power 150 W, 15% $CH_4$, 7.5 mTorr, and 14 cm distance, resulting in about 3 $\mu\textrm{m}$/hr etch rate with smooth surfaces and vertical mesa sidewalls.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.297-299
• /
• 2003

In this paper, we present the fabrication of copper electrode array and test of electrochemical discharge machining for the fabrication of microholes on Borofloat33 glass. Copper electrode array is fabricated by the bonding of silicon upper substrate and lower substrate and copper electroplate. The silicon upper electrode having microholes fabricated by ICP-RIE is the mold of copper electroplate. The lower substrate is used as the seed layer for copper electroplate after Au - Au thermocompression bonding with the upper substrate.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.330-333
• /
• 1999

A Schottky characteristic is one of the important properties to determine the performance of GaN electronic devices. In this paper, we have studied how to improve the property after n$^{+}$ layer etching by ICP(Induced Coupled Plasma)-RIE(Reactive ion Etching). We have tried $N_2$radiation, annealing after $N_2$radiation, and annealing in $N_2$environment. We have found that a simple annealing method in $N_2$environment is enough to improve the Schottky characteristic for electronic device-Quality application.n.