• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.168-168
• /
• 2008

Dimension of a transistor has rapidly shrunk to increase the speed of device and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate dioxide layer and low conductivity characteristic of poly-Si gate in nano-region. To cover these faults, study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$, and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-Si gate is not compatible with high-k materials for gate-insulator. Poly Si gate with high-k material has some problems such as gate depletion and dopant penetration problems. Therefore, new gate structure or materials that are compatible with high-k materials are also needed. TiN for metal/high-k gate stack is conductive enough to allow a good electrical connection and compatible with high-k materials. According to this trend, the study on dry etching of TiN for metal/high-k gate stack is needed. In this study, the investigations of the TiN etching characteristics were carried out using the inductively coupled $BCl_3$-based plasma system and adding $Cl_2$ gas. Dry etching of the TiN was studied by varying the etching parameters including $BCl_3$/Ar gas mixing ratio, RF power, DC-bias voltage to substrate, and $Cl_2$ gas addition. The plasmas were characterized by optical emission spectroscopy analysis. Scanning electron microscopy was used to investigate the etching profile.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.17-18
• /
• 2007

The etching characteristics of Zinc Oxide (ZnO) and etch selectivity of ZnO to $SiO_2\;in\;BCl_3$/Ar plasma were investigated. It was found that ZnO etch rate shows a non-monotonic behavior with increasing both Ar fraction in $BCl_3$ plasma, RF power, and gas pressure. The maximum ZnO etch rate of 50.3 nm/min was obtained for $BCl_3$ (80%)/Ar(20%) gas mixture. The plasmas were characterized using optical emission spectroscopy (OES) analysis measurements while chemical state of etched surfaces was investigated with X-ray photoelectron spectroscopy (XPS). From these data the suggestions on the ZnO etch mechanism were made.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.322-325
• /
• 2003

BST thin films were etched with inductively coupled plasmas. A chemically assisted physical etch of BST was experimentally confirmed by ICP under various gas mixtures. After a 20 % addition of $BCl_3$ to the $Cl_2/Ar$ mixture, resulting in an increased the chemical effect. As a increases of RF power, substrate power, and substrate temperature, and decrease of working pressure, the ion energy flux and chlorine atoms density increased. The maximum etch rate of the BST thin films was 90.1 nm/min at the RF power, substrate power, working pressure, and substrate temperature were 700 W, 300 W, 1.6 Pa, and 20 $^{\circ}C$, respectively. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching product.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.244-250
• /
• 2008

An inductively coupled plasma etching process to replace an existing slower rate reactive ion etching process for $60{\mu}m$ diameter via-holes using Cl2/BCl3 gases has been investigated. Process pressure and platen power were varied at a constant ICP coil power to reproduce the RIE etched $200{\mu}m$ deep via profile, at high etch rate. Desired etch profile was obtained at 40 m Torr pressure, 950 W coil power, 90W platen power with an etch rate ${\sim}4{\mu}m$/min and via etch yield >90% over a 3-inch wafer, using $24{\mu}m$ thick photoresist mask. The etch uniformity and reproducibility obtained for the process were better than 4%. The metallized via-hole dc resistance measured was ${\sim}0.5{\Omega}$ and via inductance value measured was $\sim$83 pH.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.63-63
• /
• 2003

플라즈마 공정은 DRAM, 이종접합 양극성 트랜지스터(HBTs), 레이저, 평면도파로(planar lightwave circuit)와 같은 전자소자 및 광조자 제작에 있어서 핵심 공정중의 하나이다. 최근 미세 구조의 크기가 극도로 감소하게 됨에 따라 실제 소작 제작에 있어서 미세한 모양을 식각하는 공정이 매우 중요하게 되었다. 그 중에서 고밀도 유도결합 플라즈마(high density inductively coupled plasma)를 이용한 기술은 빠르고 정확한 식각률, 우수한 식각 균일도와 높은 재현성 때문에 습식식각 기술보다 선호되고 있다. 본 연구는 평판형(planar) 고밀도 유도결합 플라즈마 식각장치를 이용하여 BCl$_3$와 BCl$_3$/Ar 플라즈마에 따른 AlGaAs/GaAs의 식각결과를 비교 분석하였다. 공정 변수는 ICP 소스(source power)파워, RIE 척(chuck) 파워, 공정 압력, 그리고 Ar 조성비(0-100%)이었다. BCl$_3$에 Ar을 첨가하게 되면 순수한 BCl$_3$ 플라즈마에서의 AlGaAs/GaAs 식각률(> 3000 $\AA$/min) 보다 분당 약 1000$\AA$ 이상 높은 식각률(>4000 $\AA$/min)을 나타내었다. 이 결과는 Ar 플라즈마의 이온보조(ion-assisted)가 식각률 증가에 기인한다고 예측된다. 그리고 전자주사 현미경(SEM)과 원자력간 현미경(AFM)을 사용하여 식각 후 표면 거칠기 및 수직 측벽도 둥을 분석하였다. 마지막으로 XPS를 이용하여 식각된 후에 표면에 남아 있는 잔류 성분 분석을 연구하였다. 본 결과를 종합하면 BCl$_3$에 기초한 평판형 유도결합 플라즈마는 AlGaAs/GaAs 구조의 식각시 많은 우수한 특성을 보여주었다.79$\ell/\textrm{cm}^3$, 0.016$\ell/\textrm{cm}^3$, 혼합재료 2는 0.045$\ell/\textrm{cm}^3$, 0.014$\ell/\textrm{cm}^3$, 혼합재료 3은 0.123$\ell/\textrm{cm}^3$, 0.017$\ell/\textrm{cm}^3$, 혼합재료 4는 0.055$\ell/\textrm{cm}^3$, 0.016$\ell/\textrm{cm}^3$, 혼합재료 5는 0.031$\ell/\textrm{cm}^3$, 0.015$\ell/\textrm{cm}^3$, 혼합재료 6은 0.111$\ell/\textrm{cm}^3$, 0.020$\ell/\textrm{cm}^3$로 나타났다. 3. 단일재료의 악취흡착성능 실험결과 암모니아는 코코넛, 소나무수피, 왕겨에서 흡착능력이 우수하게 나타났으며, 황화수소는 펄라이트, 왕겨, 소나무수피에서 다른 재료에 비하여 상대적으로 우수한 것으로 나타났으며, 혼합충진재는 암모니아의 경우 코코넛과 펄라이트의 비율이 70%:30%인 혼합재료 3번과 소나무수피와 펄라이트의 비율이 70%:30%인 혼합재료 6번에서 다른 혼합재료에 비하여 우수한 것으로 나타났으며, 황화수소의 경우 혼합재료에 따라 약간의 차이를 보였다. 4. 코코넛과 소나무수피의 경우 암모니아가스에 대한 흡착성능은 거의 비슷한 것으로 사료되며, 코코넛의 경우 전량을 수입에 의존하고 있다는 점에서 국내 조달이 용이하며, 구입 비용도 적게 소요되는 소나무수피를 사용하는 것이 경제적이라고 사료된다. 5. 마지막으로 악취제거 미생물균주를 접종한 소나무수피 70%와 펄라이트 30%의 혼합재료를 24시간동안 장기간 운전

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.135-136
• /
• 2009

The etching characteristics of Zinc Oxide (ZnO) and etch selectivity of ZnO to $SiO_2$ in $BCl_3/Ar/Cl_2$ plasma were investigated. It was found that ZnO etch rate shows a non-monotonic behavior with increasing both Ar fraction in $BCl_3$ plasma, RF power, and gas pressure. The maximum ZnO etch rate of 53 nm/min was obtained for $BCl_3$(16 sccm)/Ar(4 sccm)/$Cl_2$(3 sccm) gas mixture. The chemical state of etched surfaces was investigated with X-ray photoelectron spectroscopy (XPS). From these data, the suggestions on the ZnO etch mechanism were made.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.335-340
• /
• 2013

In this study, the plasma etching of the TaN thin film with $CH_4/BCl_3/Ar$ gas chemistries was investigated. The etch rate of the TaN thin film and the etch selectivity of TaN to $SiO_2$ was studied as a function of the process parameters, including the amount of $CH_4$. X-ray photoelectron spectroscopy (XPS) and Field-emission scanning electron microscopy (FE-SEM) was used to investigate the chemical states of the surface of the TaN thin film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.105-105
• /
• 2009

$ZrO_2$ is one of the most attractive high dielectric constant (high-k) materials. As integrated circuit device dimensions continue to be scaled down, high-k materials have been studied more to resolve the problems for replacing the EY31conventional $SiO_2$. $ZrO_2$ has many favorable properties as a high dielectric constant (k= 20~25), wide band gap (5~7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2/Si$ structure. In order to get fine-line patterns, plasma etching has been studied more in the fabrication of ultra large-scale integrated circuits. The relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Due to the easy control of ion energy and flux, low ownership and simple structure of the inductively coupled plasma (ICP), we chose it for high-density plasma in our study. And the $BCl_3$ included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compound In this study, the surface kinetic properties of $ZrO_2$ thin film was investigated in function of Ch addition to $BCl_3/Ar$ gas mixture ratio, RF power and DC-bias power based on substrate temperature. The figure 1 showed the etch rate of $ZrO_2$ thin film as function of gas mixing ratio of $Cl_2/BCl_3/Ar$ dependent on temperature. The chemical state of film was investigated using x-ray photoelectron spectroscopy (XPS). The characteristics of the plasma were estimated using optical emission spectroscopy (OES). Auger electron spectroscopy (AES) was used for elemental analysis of etched surface.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.3
• /
• pp.164-169
• /
• 2014

We investigated the etching characteristics of $HfAlO_3$ thin films in $O_2/Cl_2/Ar$ and $O_2/BCl_3/Ar$ gas, using a high-density plasma (HDP) system. The etch rates of the $HfAlO_3$ thin film obtained were 30.1 nm/min and 36 nm/min in the $O_2/Cl_2/Ar$ (3:4:16 sccm) and $O_2/BCl_3/Ar$ (3:4:16 sccm) gas mixtures, respectively. At the same time, the etch rate was measured as a function of the etching parameter, namely as the process pressure. The chemical states on the surface of the etched $HfAlO_3$ thin films were investigated by X-ray photoelectron spectroscopy. Auger electron spectroscopy was used for elemental analysis on the surface of the etched $HfAlO_3$ thin films. These surface analyses confirm that the surface of the etched $HfAlO_3$ thin film is formed with nonvolatile by-product. Also, Cl-O can protect the sidewall due to additional $O_2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.382-382
• /
• 2010

The etch characteristics of the $HfAlO_3$ thin films and selectivity of $HfAlO_3$ to $SiO_2$ in $Cl_2/BCl_3$/Ar plasma were investigated in this work. The maximum etch rate was 108.7 nm/min and selectivity of $HfAlO_3$ to $SiO_2$ was 1.11 at $Cl_2$(3sccm)/$BCl_3$(4sccm)/Ar(16sccm), RF power of 500 W, DC-bias voltage of - 100 V, process pressure of 1 Pa and substrate temperature of $40^{\circ}C$. As increasing RF power and DC-bias voltage, etch rates of the $HfAlO_3$ thin films increased. Whereas as decreasing of the process pressure, those of the $HfAlO_3$ thin films were increased. The chemical reaction on the surface of the etched the $HfAlO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS).