• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.4
• /
• pp.56-64
• /
• 2006

Generally, Permanent Magnet Brushless DC Motor(PM BLDC) is necessary the Hall-IC to detect the rotor position. But it will take place the operation standstill of motor or error of rotor position detection according to the circumference temperature, humidity, or limited surroundings. This paper propose the algorithm of rotor position detection only using one or two Hall-IC. Therefore we can estimate information of the others phase in sequence through a rotor instead of using three Hall-IC at 3 phase motor. This paper identify the same characteristics, performance and function of protection circuit by the proposed algorithm with the 3 phase PM BLDC motor in comparison with general method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.60-67
• /
• 2010

We designed Average Current Control PFC IC which has make the average value of boost inductor current became the shape of sine wave. Designed IC has fixed frequency of 75kHz to meet EMI standard requirement. And also RC compensation loop has been designed into the error amp and the current amp, in order that it has wide bandwidth for high speed control. And we use the oscillator which generates by square wave and triangle wave, and add to UVLO, OVP, OCP, TSD which is in order to operate stability. We simulated by using Spectre of Cadence to verify the unity power factor function and various protection circuits and fabricated in a $1{\mu}m$ High Voltage(20V) CMOS process.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2568-2571
• /
• 2002

A LCD backlight inverter control IC based on the piezoelectric transformer (PZT) for Cold Cathode Fluorescent Lamp (CCFL) lighting is proposed. It is indeed a variable frequency, variable duty (VFVD) controller having dual feedback control loops for achieving both the regulation of lamp current and the maximum efficiency. The PWM controller regulates the lamp current, while the PLL controller tunes the operating frequency to the frequency that the efficiency of the combined LC-PZT resonator becomes maximum. The mixed PLL/PWM control technique lets the backlight inverter operate at the maximum efficiency in spite of the variation of component and environment. The controller features include a protection for an open or broken lamps, and an open lamp regulation.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.162-163
• /
• 2007

본 논문에서는 600V/200A 또는 1200V/150A와 같은 고 전력 절연 게이트 소자를 구동 및 보호하기 위한 파워 IC에 대한 연구에 대해서 살펴보았다. 고 전력 소자의 구동을 위해서 최대 Sourcing 전류 4A, 최대 Sinking 전류 8A로 설계하였으며, 과전류 보호회로로는 전력소자의 Desaturation을 검출하는 방식을 사용하였다. 또한 과전류 보호시 발생할 수 있는 과전압을 억제하기 위해서 Soft turn-off 기능을 추가하였다. 동부하이텍의 고전압 BCDMOS 공정인 0.35um BDA350 공정과 PDK를 사용하여 설계 및 제작하였다.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.169-172
• /
• 2002

A protection integrated circuit which enables the stable operation of the rechargeable battery should be designed with a low-power architecture because it consumes the power of the battery. This paper proposed a low-power scheme especially when the several series-connected batteries are provided. By adopting a time sharing control of the batteries, the chip size and power consumption could be reduced.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.319-326
• /
• 1997

The fire accident cases of several countries such as Korea, Japan, United States, etc., were collected and compared statistically. The trends of fire accidents in several countries will help us establish detailed plans for fire protection and reduce the possible fire accidents in the future. For construction of data base system, the program FADS was developed, which is operable in Windows environment.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.4
• /
• pp.195-200
• /
• 2006

The conventional discrete circuit for ABS/TCS system was examined and the problems of the system were analyzed by computer simulation. In order to improve the performance of ABS/TCS system, interface IC which has error compensation, comparator and under voltage lock-out circuit was designed and their electrical characteristics were investigated. The voltage regulator was included to compensate the temperature variation in the temperature range from $-20^{\circ}C$ to $120^{\circ}C$ for automobile environment. ABS and brake signal were separated using the duty factor of same frequency or different frequencies. UVLO(Under Voltage Lock-Out) circuit and constant current circuit were applied for the elimination of noise, and protection circuit was applied to cut the excess current off. Layout for IC fabrication was designed to enhance the electrical performance of ABS/TCS system. Layout was consisted of 11 masks, arrayed effectively 8 pads to reduce the current loss. We can see that the result of layout simulation was better than the result of bread board.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.3
• /
• pp.221-228
• /
• 2011

This paper describes 250-Mb/s fiber optic transmitter and receiver ICs for plastic optical fiber applications using a$ 0.18-{\mu}m$ CMOS technology. Simple signal and light detection schemes are introduced for power reduction in sleep mode. The transmitter converts non-return-to-zero digital data into 650-nm visible-red light signal and the receiver recovers the digital data from the incident light signal through up to 50-m plastic optical fiber. The transmitter and receiver ICs occupy only 0.62 $mm^2$ of area including electrostatic discharge protection diodes and bonding pads. The transmitter IC consumes 23 mA with 20 mA of LED driving currents, and the receiver IC consumes 16 mA with 4 mA of output driving currents at 250 Mb/s of data rate from a 3.3-V supply in active mode. In sleep mode, the transmitter and receiver ICs consume only 25 ${\mu}A$ and 40 ${\mu}A$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.719-726
• /
• 2008

In this paper, we designed driving IC for 500 V resonant half-bridge type power converter, In this single-ended level shifter, chip area and power dissipation was decreased by 50% and 23.5% each compared to the conventional dual-ended level shifter. Also, this newly designed circuit solved the biggest problem of conventional flip-flop type level shifter in which the power MOSFET were turned on simultaneously due to the large dv/dt noise. The proposed high side level shifter included switching noise protection circuit and schmmit trigger to minimize the effect of displacement current flowing through LDMOS of level shifter when power MOSFET is operating. The designing process was proved reasonable by conducting Spectre and PSpice simulation on this circuit using 1${\mu}m$ BCD process parameter.