• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.469-472
• /
• 1999

CeO$_2$ thin films have used in wide applications such as SOI, buffer layer, antirflection coating, and gate dielectric layer. CeO$_2$takes one of the cubic system of fluorite structure and shows similar lattice constant (a=0.541nm) to silicon (a=0.543nm). We investigated CeO$_2$films as buffer layer material for nonvolatile memory device application of a single transistor. Aiming at the single transistor FRAM device with a gate region configuration of PZT/CeO$_2$ /P-Si , this paper focused on CeO$_2$-Si interface properties. CeO$_2$ films were grown on P-type Si(100) substrates by 13.56MHz RF magnetron sputtering system using a 2 inch Ce metal target. To characterize the CeO$_2$ films, we employed an XRD, AFM, C-V, and I-V for structural, surface morphological, and electrical property investigations, respectively. This paper demonstrates the best lattice mismatch as low as 0.2 % and average surface roughness down to 6.8 $\AA$. MIS structure of CeO$_2$ shows that breakdown electric field of 1.2 MV/cm, dielectric constant around 13.6 at growth temperature of 200 $^{\circ}C$, and interface state densities as low as 1.84$\times$10$^{11}$ cm $^{-1}$ eV$^{-1}$ . We probes the material properties of CeO$_2$ films for a buffer layer of FRAM applications.

• Membrane and Water Treatment
• /
• v.9 no.4
• /
• pp.211-220
• /
• 2018

Incorporating nano-materials in thin-film composite (TFC) membranes has been considered to be an approach to achieve higher membrane performance in various water treatment processes. This study investigated the rejection efficiency of three target compounds, i.e., reserpine, norfloxacin and tetracycline hydrochloride, by TFC membranes with different graphene oxide proportions. Graphene oxide (GO) was incorporated into the polyamide active layer of a TFC membrane via an interfacial polymerization (IP) reaction. The TFC membranes were characterized with FTIR, FE-SEM, AFM; in addition, the water contact angle measurements as well as the permeation and separation performance were evaluated. The prepared GO-TFC membranes exhibited a much higher flux ($3.11{\pm}0.04L/m2{\cdot}h{\cdot}bar$) than the pristine TFC membranes ($2.12{\pm}0.05L/m2{\cdot}h{\cdot}bar$) without sacrificing their foulant rejection abilities. At the same time, the GO-modified membrane appeared to be less sensitive to pH changes than the pure TFC membrane. A significant improvement in the anti-fouling property of the membrane was observed, which was ascribed to the favorable change in the membrane's hydrophilicity, surface morphology and surface charge through the addition of an appropriate amount of GO. This study predominantly improved the understanding of the different PA/GO membranes and outlined improved industrial applications of such membranes in the future.

• Molecules and Cells
• /
• v.41 no.2
• /
• pp.73-82
• /
• 2018

Cancer preventive activities of green tea and its main constituent, (-)-epigallocatechin gallate (EGCG) have been extensively studied by scientists all over the world. Since 1983, we have studied the cancer chemopreventive effects of EGCG as well as green tea extract and underlying molecular mechanisms. The first part of this review summarizes groundbreaking topics with EGCG and green tea extract: 1) Delayed cancer onset as revealed by a 10-year prospective cohort study, 2) Prevention of colorectal adenoma recurrence by a double-blind randomized clinical phase II trial, 3) Inhibition of metastasis of B16 melanoma cells to the lungs of mice, 4) Increase in the average value of Young's moduli, i.e., cell stiffness, for human lung cancer cell lines and inhibition of cell motility and 5) Synergistic enhancement of anticancer activity against human cancer cell lines with the combination of EGCG and anticancer compounds. In the second part, we became interested in cancer stem cells (CSCs). 1) Cancer stem cells in mouse skin carcinogenesis by way of introduction, after which we discuss two subjects from our review on human CSCs reported by other investigators gathered from a search of PubMed, 2) Expression of stemness markers of human CSCs compared with their parental cells, and 3) EGCG decreases or increases the expression of mRNA and protein in human CSCs. On this point, EGCG inhibited self-renewal and expression of pluripotency-maintaining transcription factors in human CSCs. Human CSCs are thus a target for cancer prevention and treatment with EGCG and green tea catechins.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.215-219
• /
• 2004

Metal-chelate derivatives have been investigated intensively as an emitting layer and recognize to have excellent electroluminescence(EL) properties. We synthesized new luminescent material, 1,4-dihydoxy-5,8-naphtaquinone $Aiq_3$ complex($Al_2Nq_4$) and investigated the electrical optical properties. OLED has potential candidates for information display with merits of thickness, low power and high efficiency. Although the OLED show a lot of advantages for information display, it has the limit of inorganic(metal)/ organic interface. In this study, the two methods are used to study the interface of metal/organic in OLED. First, we treated $O_2$ plasma on an ITO thin film by using RIE system, and analyzed the ingredient of ITO thin film according to change of the processing conditions. We used the RDS and the XPS for the ingredient analysis of the surface and bulk. We measured electrical resistivity using Four-Point-Probe and calculated sheet resistance, and ITO surface roughness was measured by using AFM. We fabricated OLED using substrate that was treated optimum ITO surface. Second, we used the buffer layer of CuPc to improve the characteristics of the interface and the hole injection in OLED. The result of the study for electrical and optical properties by using I V L T System(Flat Panel Display Analysis System), we confirmed that the electrical properties and the luminance properties were improved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.45-45
• /
• 2007

Capacitors among the embedded passive components are most widely studied because they are the major components in terms of size and number and hard to embed compared with resistors and inductors due to the more complicated structure. To fabricate a capacitor-embedded PCB for in-line process, it is essential to adopt a low temperature process (<$200^{\circ}C$). However, high dielectric materials such as ferroelectrics show a low permittivity and a high dielectric loss when they are processed at low temperatures. To solve these contradicting problems, we studied BMN materials as a candidate for dielectric capacitors. processed at PCB-compatible temperatures. The morphologies of BMN thin films were investigated by AFM and SEM equipment. The electric properties (C-F, I-V) of Pt/BMN/Cu/polymer were evaluated using an impedance analysis (HP 4194A) and semiconductor parameter analyzer (HP4156A). $Bi_2Mg_{2/3}Nb_{4/3}O_7$(BMN) thin films deposited on copper clad laminate substrates by sputtering system as a function of Ar/$O_2$ flow rate at room temperature showed smooth surface morphologies having root mean square roughness of approximately 5.0 nm. 200-nm-thick films deposited at RT exhibit a dielectric constant of 40, a capacitance density of approximately $150\;nF/cm^2$, and breakdown voltage above 6 V. The crystallinity of the BMN thin films was studied by TEM and XRD. BMN thin film capacitors are expected to be promising candidates as embedded capacitors for printed circuit board (PCB).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.342-342
• /
• 2007

원자층 증착(Atomic Layer Deposition: ALD) 방법은 반응물질들을 펄스형태로 챔버에 공급하여 기판 표면에 반응물질의 표면 포화반응에 의한 화학적 흡착과 탈착을 이용한 박막증착기술이다. ALD법은 박막의 조성 정밀제어가 쉽고, 파티클 발생이 없으며, 대면적의 박막 증착시 균일성이 우수하고, 박막 두께의 정밀 조절이 용이한 장점이 있다. 원자층 증착 공정에서 짧은 시간 안에 소스를 충분히 공급하기 위한 방법으로는 소스 온도를 증가시켜 전구체의 증기압을 높여 반응기로의 유입량을 증가시키는 방법, 전구체의 공급시간을 늘리는 방법 등을 들 수 있다. 그러나 전구체 온도를 상승시키는 경우, 공정 조건의 변화가 요구되며 전구체의 변질에 의하여 형성된 막이 의도하는 막 특성을 만족시키지 못하게 되는 문제점이 발생될 우려가 있다. 그리고 전구체를 충분히 공급하기 위하여 전구체의 공급시간을 늘이는 방법을 사용하면, 원하는 두께의 막을 형성하기 위하여 소요되는 공정시간이 증가된다. 이를 해결하기 위해 수송가스를 이용한 버블러 형태의 전구체 공급 장치를 사용하지만 이 또한 전구체의 수명을 단축시키는 단점을 가지고 있다. 본 논문에서는 위의 문제점을 극복할 수 있는 새로운 개념의 수송가스 도움 전구체 공급 장치를 소개한다. 본 연구에서 사용된 수송가스 도움 전구체 공급 장치를 가지는 ALD 장비는 Lucida-D200 (NCD Technology사)이며 기판으로는 8인치 실리콘 웨이퍼를 사용하였으며 (TEMA)Zr을 사용하여 ZrO2 박막을 성장하였다. 수송가스 도움 전구체 공급 장치를 사용한 경우, 그렇지 않은 경우 보다 $30^{\circ}C$ 이상 전구체 온도를 낮출 수 있으며, 또한 증착 속도를 약 2배정도 증가시킬 수 있었다. 이들 박막들은 XRD, XPS, AFM 등을 이용하여 결정구조, 결합에너지, 표면 거칠기 등의 특성을 관찰하였다. 그리고 C-V, I-V 측정을 이용해 정전용량, 유전율, 누설전류 등의 전기적 특성을 평가하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.74-77
• /
• 2004

[ $HfO_2$ ] dielectric layers were grown on the p-type Si(100) substrate by metalorganic molecular beam epitaxy(MOMBE). Hafnium $t-butoxide[Hf(O{\cdot}t-C_4H_9)_4]$ was used as a Hf precursor and Argon gas was used as a carrier gas. The thickness of the layers was measured by scanning electron microscopy (SEM) and high-resolution transmission electron measurement(HR-TEM). The properties of the $HfO_2$ layers were evaluated by X-ray diffraction(XRD), high frequency capacitance-voltage measurement(HF C-V), current-voltage measurement(I-V), and atomic force measurement(AFM). HF C-V measurements have shown that $HfO_2$ layer grown by MOMBE has a high dielectric constant(k=19-21). The properties of $HfO_2$ films are affected by various process variables such as substrate temperature, bubbler temperature, Ar, and $O_2$ gas flows. In this paper, we examined the relationship between the $O_2/Ar$ gas ratio and the electrical properties of $HfO_2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.230-230
• /
• 2010

유기물 반도체 화합물인 Cu-Pc(copper(II)-phthalocyanine)는 우수한 전기적 광학적 특성을 가지며, OLED, MISFET등 소자로서의 활용도가 높다. Cu-Pc 화합물은 $\alpha$-phase, $\beta$-phase, $\gamma$-phase를 포함하는 여러 가지 다결정 polymer로 존재할 수 있다. 가장 잘 알려진 구조로는 열적으로 준안정적인 $\alpha$-phase와 열적으로 안정적인 $\beta$-phase가 있다. Cu-Pc 박막의 구조 및 흡수 특성과 전기적 특성에 대한 기술이 확실히 규명되지 않아 본 연구에서는 두께와 열처리 조건에 따른 결정성 및 방향성을 조사하기 위하여 $\alpha$-phase와 $\beta$-phase의 phase transition 현상 및 전기적 광학적 특성을 규명 하고자 한다. 진공증착 방법 중 하나인 PVD 방법의 thermal evaporation deposition을 이용하여 glass, ITO 기판위에 두께와 열처리에 따른 전기적?광학적 특성을 연구하였다. Cu-Pc 박막의 성장두께는 5nm~50nm 이내로 fluxmeter 및 thickness monitor를 이용하여 제어하였다. 5nm~50nm의 두께에 따른 기판온도를 $200^{\circ}C$로 고정하여 전열 처리 및 후열 처리하여 온도에 따른 박막을 성장한 후, 결정 구조 및 특성 변화와 phase transition 분석하였다. 제작된 Cu-Pc의 박막은 $\alpha$-phase와 $\beta$-phase로 구분할 수 있으며, 열처리에 따른 phase transition 현상이 뚜렷함을 알 수 있다. XRD(X-ray diffraction)를 통하여 박막에 대한 결정 구조 분석 및 FE-SEM(field emission scanning electron microscopy)와 AFM(atomic force microscopy)을 이용하여 Cu-Pc 박막의 구조적 결정성과 방향성 등, 표면 상태와 형상구조에 대해 표면의 특성을 측정하며, 광 흡수도(UV-visible absorption spectra)을 이용하여 phase transition 현상에 따른 I-V 특성을 비교분석 하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.206-206
• /
• 2010

정보화 기술이 급속히 발전함에 따라서 보다 많은 양의 data를 전송, 처리, 저장 하게 되면서 이를 처리 할 수 있는 대용량, 고속, 비휘발성의 차세대 메모리의 개발이 요구 되고 있다. 이 중 저항 변화 메모리(ReRAM)는 일반적으로 전이금속산화물을 이용한 MIM 구조로서 적당한 전기 신호를 가하면 저항이 높아서 전도되지 않는 상태(Off state)에서 저항이 낮아져 전도가 가능한 상태(On state)로 바뀌는 메모리 특성을 가진다. ReRAM은 비휘발성 메모리이며 종래의 비휘발성 기억소자인 Flash memory 보다 access time이 $10^5$배 이상 빠르며, 2~5V 이하의 낮은 전압에서 동작이 가능하다. 또한 구조가 간단하여 공정상의 결함을 현저히 줄일 수 있다는 점 등 많은 장점들이 있어서 Flash memory를 대체할 수 있는 유력한 후보로 여겨지고 있다. 저항 변화의 특징을 잘 나타내는 물질에는 $TiO_2$, $Al_2O_3$, $NiO_2$, $HfO_2$, $ZrO_2$등의 많은 전이금속산화물들이 있다. 본 연구에서는 Reactive DC-magnetron Sputtering 방법과 DC-magnetron sputter를 이용하여 Ti를 증착한 후 Oxidation 방법으로 각각 증착한 $TiO_2$박막을 사용하여 저항변화특성을 관찰하였다. $TiO_2$상부에 Atomic Layer Deposition (ALD)를 이용하여 $HfO_2$ 박막을 증착하여 표면처리를 하고, 또한 $TiO_2$에 다른 전이 금속박막 층을 추가 증착하여 저항변화 특성에 접합한 조건을 찾는 연구를 진행하였다. 하부 전극과 상부 전극 물질로는 Si 100 wafer 위에 Pt 또는 TiN을 사용하였다. 저항변화 특성을 평가하기 위해 Agilent E5270B를 이용하여 current-voltage (I-V)를 측정하였다. X-ray Diffraction (XRD)를 이용하여 증착 된 전기금속 박막 물질의 결정성을 관찰했으며, Atomic Force Microscopy (AFM)을 이용하여 증착 된 샘플의 표면을 관찰했다. SEM과 TEM을 통해서는 sample의 미세구조를 확인 하였다.

• Korean Journal of Metals and Materials
• /
• v.50 no.11
• /
• pp.801-808
• /
• 2012

TiAlCN coatings with various C contents were synthesized by unbalanced magnetron sputtering. The characteristics, the crystalline structure, surface morphology, hardness, and friction coefficient of the coatings as a function of the C content were investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), a microhardness tester, and a wear test. In addition, their corrosion behaviors in a deaerated 3.5 wt% NaCl solution at $40^{\circ}C$ were investigated by potentiodynamic polarization tests. The results indicated that the $Ti_{14.9}Al_{15.5}C_{30.7}N_{38.9}$ coating had the highest hardness, elastic modulus, and a plastic deformation resistance of 39 GPa, 359 GPa, and 0.55, respectively, and it also had the lowest friction coefficient of approximately 0.26. Comparative evaluation of the TiAlCN coatings indicated that a wide range of coating properties, especially coating hardness, could be obtained by the synthesis methods and processing variables. The microhardness of the coatings was much higher than that from previously reported coating using similar magnetron sputtering processes. It was almost as high as the microhardness measured from the TiAlCN coatings (~41 GPa) synthesized using an arc ion plating process. The potentiodynamic test showed that the corrosion resistance of the TiAlCN coatings was significantly better than the TiAlN coatings, and their corrosion current density ($i_{corr}$), corrosion potentials ($E_{corr}$) and corrosion rate decreased with an increasing C content in the coatings. The much denser microstructure of the coatings due to the increased amount of amorphous phase with increasing C contents in the coatings could result in the the improved corrosion resistance of the coatings.