• 한국표면공학회지
• /
• 제19권2호
• /
• pp.31-43
• /
• 1986

The properties of the electroless nickel deposit mainly depends on the pH of the bath, the plating temperature, and the molar ratio of nickel to hypophosphite but they are also affected by its formulation and concentration of complexing and buffering agents. According to changeing the concentration of triethanolamine and boric acid, phosphorous contents, microsturcture, crystalline, hardness and wear resistance of deposits obtained from ammoniacal alkaline bath were investigated by EPMA, differential thermal analyser, X-ray diffractometer and wear tester. The results are as follows; (1) Increasing concentration of triethanolamine in the bath, the deposits is slightly inclined to increase its phosphorous content(3.7% P). (2) In the as-plated state, the deposits are not crystallized state but they are thermally unstable phase, and they are crystallized with precipitating $Ni_3P$ at 400$^{\circ}C$. (3) The deposit containing 2.3% P has higher hardness value in the as plated and heat treated state at below 300$^{\circ}C$ than those of 3.7% phosphorous deposit (1090Hk). But in the case of heat treating at 400$^{\circ}C$, the former has lower hardness value (1000Hk) than the latter and has remarkably Ni(III) orientation by heat treatment. (4) The 3.7% phosphorous deposit heat treated at 400$^{\circ}C$ has better wear resistance than hard chromium plating.

• 한국표면공학회지
• /
• 제19권4호
• /
• pp.140-148
• /
• 1986

Using sodium pyrophoshate as complexing agent, the characteristics and the magnetic properties of the films deposited from electroless cobalt plating bath have been studied. The result obtained are as following; 1. It was found that the optimum bath compositions consisted of 0.1M cobalt sulfate, 0.2M sodium hypophosphite as reducing agent, 0.4M sodium pyrophosphate as complexing agent and 0.5M ammonium sulfate as buffer agent, whereas good operating conditions were the bath of pH 10.5 adjusted with ammonia and 70$^{\circ}C$ of bath temperature, respectively. 2. The coercive force and the squareness of magnetic films were increased with deposition from the low temperature bath. 3. The phosphorous content in Co-P films deposited from these bath was relatively higher than that from Brenner bath. It was assumed to be due to codeposition of phosphorous from the pyrophosphate anion in the solution.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.708-711
• /
• 1999

The Cu/Ni/Au lamellar structure is extensively used as an under bump metallization on silicon file, and on printed circuit board(PCB) pads. Ni is plated Cu by either electroless Ni plating, or electrolytic Ni plating. Unlike the electrolytic Ni plating, the electroless Ni plating does not deposit pure Ni, but a mixture of Ni and phosphorous, because hypophosphite Is used in the chemical reaction for reducing Ni ions. The fracture crack extended at the interface between solder balls of plastic ball grid (PBGA) package and conducting pads of PCB. The fracture is duets to segregation at the interface between Ni$_3$Sn$_4$intermetallic and Ni-P layer. The XPS diffraction results of Cu/Ni/Au results of CU/Ni/AU finishs showed that the Ni was amorphous with supersaturated P. The XPS and EDXA results of the fracture surface indicated that both of the fracture occurred on the transition lesion where Sn, P and Ni concentrations changed.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2004년도 춘계학술대회
• /
• pp.69-71
• /
• 2004

새로운 기술인 Momentary mold surface heating(MmSH)은 기존의 사출성형법으로 제조된 Acrylonitrile Butadiene Styrene(ABS)의 단점을 개선한 사출성형법이다. MmSH로 제조된 ABS와 기존의 사출성형법으로 제조된 ABS의 도금특성을 도금욕 pH 변화에 따라 연구하였다. Sodium hypophosphite가 첨가된 무전해 Ni 도금욕의 PH가 증가할수록 도금 두께가 증가하였고 기존의 사출성형법으로 제조된 ABS의 경우 pH 5이상에서 4B의 밀착력을 가졌다. MmSH로 제조된 ABS의 경우 pH 6이상에서 5B인 12.3N/25mm 이상의 가장 우수한 밀착력을 나타내었다.

• 자원리싸이클링
• /
• 제21권2호
• /
• pp.41-46
• /
• 2012

전해채취법을 이용하여 무전해 니켈 도금폐액으로부터 니켈을 회수하기 위한 실험을 수행하였다. 이를 위해 우선 가성소다를 첨가하는 방법으로 무전해 니켈 도금폐액중의 니켈을 수산화물 형태로 침전분리하였다. 또한, 니켈 수산화물을 황산 용액으로 용해시킨 니켈 수용액을 대상으로 전기분해를 실시하였다. 실험결과, 가성소다를 첨가하여 pH 10 이상으로 조절하면 99% 이상의 Ni을 수산화물로 침전시킬 수 있는 것으로 나타났다. 한편, 니켈 수용액으로부터 전해채취를 통한 Ni의 석출시 전류밀도가 증가할수록 전류효율은 감소하는 것으로 나타났다.

• 공업화학
• /
• 제26권3호
• /
• pp.270-274
• /
• 2015

본 연구에서는 고농도 무전해 니켈도금 폐액을 처리하기 위한 고도산화공정 기술을 개발하였다. 추출, 농축 공정을 이용한 니켈 금속 회수보다는 폐수를 방류수 수준으로 처리할 수 있는 기술 개발을 위하여 차아인산염과 아인산염을 침전이 용이한 인산염으로 효과적으로 전환시킬 수 있는 공정 개발에 초점을 맞추었다. 광화학적 방법인 $UV/H_2O_2$ 방식을 채택하여 COD, $PO_4-P$ 변화 효율 및 과산화수소의 소모량을 분석함으로써 고농도 무전해 니켈도금 폐액의 고도산화처리 특성을 평가하였다. 특히, $UV/H_2O_2/O_3$ 방식으로 오존산화법을 추가함으로써 과산화수소 사용량을 30% 가량 절감하고 처리시간을 약 6 h 단축시킬 수 있었다.

• 환경위생공학
• /
• 제18권3호통권49호
• /
• pp.35-42
• /
• 2003

The electric resistance and constant current were investigated on the nickel-thallium-phosphorus alloy deposits by electroless-plating. The Ni-Tl-P alloy deposits were achieved with a bath using sodium hypophosphit as the reducing agent and sodium citrate as the comlexing agent. The basic plating solution is composed of 0.1M NiSO$_4$, 0.005${\sim}$0.0IM Tl$_2$S0$_4$, 0.1${\sim}$O.2M sodium hypophosphite and 0.02${\sim}$O.IM sodium citrate and the plating condition were pH 5${\sim}$6, temperrature 80$_4$90${\circ}$C. The results obtained are summarized as follows: 1) The crystal structure of deposit was amorphous structure as deposited state, became microcrystallized centering on Ni(111) plane by heat treatment at 200${\circ}$C, and grew as polycrystalline Ni, Ni$_3$P, Ni$_5$p$_2$,Tl, etc. by heat treatment higher than 350${\circ}$C. The grain size of plated deposits was grown up to 28.3~42.0nm by heat treatment for 1hour at 500${\circ}$C. 2) The electrical resistivity showed a comparatively high value of 192.5$_4$208.3 ${\mu}$${\Omega}$Cm and its thermal stability was great with resistivity value less than 0.22% in the thermal surroundings of 200${\circ}$C. 3) Ni-Tl-P alloy deposit showed such good constant current-making-effect in the variation of electric voltage, heat treatment temperature, and the composition of the deposit that it can be put to practical use as the matter of constant current device.

• 한국재료학회지
• /
• 제23권11호
• /
• pp.661-665
• /
• 2013

We investigated the characteristics of electroless plated Cu films on screen printed Ag/Anodized Al substrate. Cu plating was attempted using neutral electroless plating processes to minimize damage of the anodized Al substrate; this method used sodium hypophosphite instead of formaldehyde as a reducing agent. The basic electroless solution consisted of $CuSO_4{\cdot}5H_2O$ as the main metal source, $NaH_2PO_2{\cdot}H_2O$ as the reducing agent, $C_6H_5Na_3O_7{\cdot}2H_2O$ and $NH_4Cl$ as the complex agents, and $NiSO_4{\cdot}6H_2O$ as the catalyser for the oxidation of the reducing agent, dissolved in deionized water. The pH of the Cu plating solutions was adjusted using $NH_4OH$. According to the variation of pH in the range of 6.5~8, the electroless plated Cu films were coated on screen printed Ag pattern/anodized Al/Al at $70^{\circ}C$. We investigated the surface morphology change of the Cu films using FE-SEM (Field Emission Scanning Electron Microscopy). The chemical composition of the Cu film was determined using XPS (X-ray Photoelectron Spectroscopy). The crystal structures of the Cu films were investigated using XRD (X-ray Diffraction). Using electroless plating at pH 7, the structures of the plated Cu-rich films were typical fcc-Cu; however, a slight Ni component was co-deposited. Finally, we found that the formation of Cu film plated selectively on PCB without any lithography is possible using a neutral electroless plating process.

• 폴리머
• /
• 제31권3호
• /
• pp.184-188
• /
• 2007

산성 도금조에서 차인산나트륨을 환원제로 하는 무전해 도금법을 사용하여 직경 $4{\mu}m$의 PMMA(poly-methylmethacrylate)/HDDA(1,6-hexanedioldiacrylate) 단분산 가교 고분자 미립자에 니켈층을 코팅할 시 1) 전처리 조건변화, 2) 도금조 온도변화, 3) 도금조 pH 변화, 및 4) 초기 도금조 pH 조절 등에 따라서 도금속도, 도금면의 상태 및 도금 재현성을 관찰하였다. 무전해 도금에서의 전처리 과정은 모든 단계가 중요하였으나 특히 conditioning 및 acceleration 과정이 균일한 도금층을 형성하는데 중요하였고, 도금조 온도 및 pH의 상승에 따라서 도금속도가 증가하였으며, 특히 초기 도금조의 pH의 조절이 도금 재현성을 확보하는데 매우 중요하였다.

• 한국재료학회지
• /
• 제19권2호
• /
• pp.61-67
• /
• 2009

Electrolessly deposited Co (Re,P) was investigated as a possible capping layer for Cu wires. 50 nm Co (Re,P) films were deposited on Cu/Ti-coated silicon wafers which acted as a catalytic seed and an adhesion layer, respectively. To obtain the optimized bath composition, electroless deposition was studied through an electrochemical approach via a linear sweep voltammetry analysis. The results of using this method showed that the best deposition conditions were a $CoSO_4$ concentration of 0.082 mol/l, a solution pH of 9, a $KReO_4$ concentration of 0.0003 mol/l and sodium hypophosphite concentration of 0.1 mol/L at $80^{\circ}C$. The thermal stability of the Co (Re,P) layer as a barrier preventing Cu was evaluated using Auger electron spectroscopy and a Scanning calorimeter. The measurement results showed that Re impurities stabilized the h.c.p. phase up to $550^{\circ}C$ and that the Co (Re,P) film efficiently blocked Cu diffusion under an annealing temperature of $400^{\circ}C$ for 1hr. The good barrier properties that were observed can be explained by the nano-sized grains along with the blocking effect of the impurities at the fast diffusion path of the grain boundaries. The transformation temperature from the amorphous to crystal structure is increased by doping the Re.