• Carbon letters
• /
• v.3 no.4
• /
• pp.198-204
• /
• 2002

In this paper, impregnated activated carbon fiber (IACF) was manufactured to pitch-based activated carbon fibers (ACF) with potassium hydroxide (KOH) by using wet impregnation method to raise nitrogen oxides ($NO_x$) adsorptivity. The properties of IACF were observed using EPMA, TGA and DSC and $NO_x$ adsorptivity was observed at high and low temperature. Before and after adsorption was analyzed using ToF-SIMS for examine surface characterization of adsorbed $NO_x$. The results showed that the better adsorptivity appeared for increasing KOH ratio. So, $NO_x$ adsorptivity showed result that is proportional between KOH and the adsorbed amount. On the other hand, adsorbent that manufactured without washing was better $NO_x$ adsorptivity than adsorbent that manufactured with washing. The behavior of adsorption show that crossing time of NO and $NO_2$ delayed for a rising adsorptivity. And NO ratio increased but $NO_2$ ratio decreased according as KOH ratio increases. $NO_x$ was confirmed through surface analysis that remain in $NO_2^-$ and $NO_3^-$ form on IACF surface.

• Archives of Pharmacal Research
• /
• v.3 no.2
• /
• pp.65-74
• /
• 1980

Analysis of particle size distribution of a sample of fine aluminum hydroxide powder was carried out by four different methods, i. e., conductivity, air permeability, gas-adsorption and sedimentation. Each method was reproducible. The results obtained by Coulter counter and sedimentation balance were similar, and the data obtained by Lea and Nurse permeameter and Stroehlein areameter were also similar. But the results differ considerabley between the former and the latter. The advantages and disavantages of each method were discussed briefly and a means of comparing the results with those obtianed by surface area measurements was shown.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.577-582
• /
• 1999

Activated carbon fibers were prepared from stabilized PAN fibers by chemical activation using hydroxide. The variations in specific surface area amount of iodine adsorption micro-structure and pore size distribution in the activated carbon fibers after the activation process were discussed. In the chemical activation using potassium hydroxide specific surface area of about 2545m2/g and amount of iodine adsorption of 2049 mg/g were obtained at the condition of KOH/fiber ratio of 1 and 800$^{\circ}C$ Nitrogen adsorption isotherms for PAN based activated carbon fibers showed the type I in the Brunauer-Deming-Deming-Teller classification indicating the micro-pores consisting the activated fibers.

• Journal of the Optical Society of Korea
• /
• v.17 no.1
• /
• pp.10-15
• /
• 2013

Adsorption behavior of counterions under a Langmuir monolayer was investigated by sum-frequency generation (SFG) spectroscopy. By comparing SFG spectra of arachidic acid (AA) Langmuir monolayer/water interface with and without added salt, it was found that the simple trivalent cation $La^{3+}$ adsorbed on AA monolayer only when the carboxylic headgroups are charged (deprotonated), implying that counterion adsorption is induced by Coulomb interaction. On the other hand, metal hydroxide complex $Fe(OH)_3$ adsorbed even on a charge-neutral AA monolayer, indicating that the adsorption of iron hydroxide is due to chemical interaction such as covalent or hydrogen bonding to the headgroup of the molecules at the monolayer.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.113-122
• /
• 2015

This study was carried out to investigate the characterization of cadmium adsorption by cellulose hydrogel and aerogel. Hydrogel and aerogel were made from ashless pulp dissolved in alkali hydroxide-urea aqueous solution and manufactured in film and bead types. After regeneration of cellulose, hydrogel went through the process of substitution of organic solvent and freeze-dry in order to make aerogel. SEM was used to analyze the microstructure of hydrogel and aerogel. Experiment was conducted in various concentrations and pH conditions to find out the characteristic of cadmium adsorption. After that, EDS was used to identify existence and distribution of cadmium in hydrogel and aerogel. The result from comparisons of cadmium adsorption shows that bead type aerogel has the maximum cadmium adsorption and film type hydrogel has the minimum cadmium adsorption.

• Textile Coloration and Finishing
• /
• v.2 no.3
• /
• pp.51-58
• /
• 1990

Cotton fabrics were mercerized in ammonia water, sodium hydroxide and mixture of ammonia/sodium hydroxide, slack and under tension. X-ray and infrared spectra analyses were used to measure crystallinity of treated cottons. Changes due to swelling, which took place in the accessible regions were determined by moisture regain and dye adsorption. In addition to that crease recovery was compared mutually, and breaking strength-elongation compared, too. Both ammonia water and caustic treatments produced changes in morphology (swollen fibers, decrease in convolutions) and in fine structure of the cellulose (increase accessibility as measured by increased moisture regain, dye adsorption). X-ray diffraction showed partial recrystallization into cellulose III lattic after tension treatment with ammonia water. Both reagents produced increased cotton elongation-at-break with slack mercerization, increased cotton breaking strength with tension mercerization, and increased moisture regain or dye adsorption with slack mercerization.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.257-265
• /
• 2017

In this work, CR (Chloroprene Rubber) was emulsified by phase-inversion emulsification with nonionic surfactants (NP-1025, LE-1017, and OP-1019) and an anionic surfactant (SDBS; sodium dodecylbenzenesulfonate), and its stabilization was investigated through a study of its adsorption characteristics, zeta potential, and flow behavior. As the amount of the mixed surfactant increased, the droplet size decreased, resulting in the increase of viscosity. In particular, a CR emulsion with a lower absorbance in the UV spectrum exhibited the highest zeta potential. The results of this experiment showed that the CR emulsion prepared using (LE-1017) and SDBS was the most stable. In this study, calcium hydroxide and aluminum hydroxide were added to enhance the mechanical properties of the CR emulsion, and the relationship between tensile strength, tear strength and surface free energy were investigated. The tensile and tear strengths of the CR emulsion incresed as the amount of calcium hydroxide and aluminum hydroxide increased. The highest tensile and tear strengths and surface free energy were observed for additions of 1.0% calcium hydroxide and 0.80% aluminum hydroxide, respectively. It was concluded that the interfacial bonding strength was improved by the even dispersion of calcium hydroxide and aluminum hydroxide in the CR emulsion.

• Journal of Korean Society on Water Environment
• /
• v.33 no.2
• /
• pp.211-218
• /
• 2017

This experiment was carried out with the purpose of testing cadmium adsorption abilities of multi wall carbon nanotube (MWCNT), activated carbon, and synthesized layered double hydroxide (LDH). In the acidic condition, only MWCNT was effective for removing cadmium ion in the aqueous phase while other adsorbents rarely removed it. The MWCNT and cadmium ion adsorption reactions followed pseudo-first order kinetic. When the initial pH value was neutral (pH = 7), cadmium ion was rapidly removed by MWCNT and activated carbon in 4 hr (100% and 99.2%, respectively). Increasing adsorbent dosages affects the pH evolution and cadmium ion removal (0 to 99%). Cytotoxicity test showed that both MWCNT and LDH has low cytotoxic effects on three kind of human cells (A549, HS-294t, and HT-29).

• Journal of the Korean Society of Clothing and Textiles
• /
• v.12 no.1 s.26
• /
• pp.27-35
• /
• 1988

In order to investigate a practical application of the fibrous adsorbent to heavy metal ions, acrylic fibers were treated with the hydroxylamine solution that was producted by hydroxylamine hydrochloride and potasium hydroxide in a condition of strong alkaline and $70^{\circ}C$. The adsorption mechanism of copper(2) ion on the fibrous adsorbent, that is hydroxylaminated acrylic fibers, was studied. The adsorption of copper(2) ion was explained in terms of the activated adsorption that are formed the complex with the ligand, such as C=N, N-H, NHOH, on the surface of the adsorbent. The activation energy was evaluated to be 3.8 Kcal/mol. and the times of adsorption equilibrium was approximately 10 minutes. The uptake of copper(2) ion was found to be effected with the increase of temperatures and the pH dependence.

• Journal of Korean Society on Water Environment
• /
• v.22 no.6
• /
• pp.991-995
• /
• 2006

The layered double hydroxide with the insertion of chloride ions (LDH-Cl), which was synthesized by the co-precipitation method, was applied to investigate the fundamental aspects of the absorptive agent for phosphate removal from wastewater. The adsorption capacity was best described by the Langmuir-FreundIich isotherm, and the estimated isotherm parameters indicate that the LDH-CI capacity for the phosphate removal is much higher than that observed using a natural adsorbent material such iron oxide tailing. The kinetic experiment also showed that the LDH-Cl adsorption reaction rapidly at the adsorptive rate of 0.55 mg-P/g-LDH/min, implying that this adsorbent can be of use in the full-scale applications. The pH had a minimal effect on the LDH adsorption capacity in the range of 5 to 11, although the capacity dropped at the low pHs because of the change in LDH surface properties. Furthermore, other anions such as $Cl^-$ and $NO_3{^-}$ commonly found in the wastewater streams insignificantly affected the phosphate removal efficiencies, while $HCO_3{^-}$ ions had a negative effect on the LDH adsorption capacity due to its high selectivity. The phosphate removal experiment using the actual secondary effluent from a wastewater treatment plant showed the similar decrease in adsorption capacity, indicating that the bicarbonate ions in the wastewater were competing with phosphate for the adsorptive site in the surface of the LDH-Cl. Overall, the synthetic adsorbent material, LDH-Cl, can be a feasible alternative over other conventional chemical agents, since the LDH-Cl exhibits the high phosphate removal capacity with the low sensitivity to other environmental conditions.