• Bulletin of the Korean Chemical Society
• /
• v.20 no.7
• /
• pp.827-830
• /
• 1999

• Resources Recycling
• /
• v.28 no.6
• /
• pp.46-53
• /
• 2019

Cement mortar was hydrothermal-synthesized with particle size of tailings using scheelite tailings deposited without proper treatment, and its physical properties were investigated. The mixing ratios of water-cement and sand-cement were fixed at 75 % and 400 %, respectively, during preparing cemnt mortar, and the sand was replaced by the tailings at 0 ~ 50 %. The particle size of tailings was controlled at 9.3 ~ 53.0 ℃, and the hydrothermal temperature was kept at 60 ~ 180 ℃ for 6 hours after the temperature increased to pretermined temperature with 2 ℃ heating rate. The compressive strength increased with increasing hydrothermal temperature. The compressive strengths were 55.2 MPa and 54.5 MPa when the mortars were prepared with 30 % low arsenic and high arsenic tailings after 60 min grinding. The compresiive strenght was enhanced 300 % compared with reference sample.

• Applied Chemistry for Engineering
• /
• v.25 no.6
• /
• pp.564-569
• /
• 2014

Zirconia nanoparticles were synthesized by hydrothermal process, and experimental parameters such as reaction temperature, reaction time, kind and concentration of precipitator, kind of precursor were varied. Particle sizes and crystalline phases of each synthesized nanoparticles were analyzed with X-ray diffraction and FE-scanning electron microscope (SEM). The particle size and crystallization of zirconia increased with increasing concentration of precipitator. The growth rate of particle sizes when NaOH as a precipitator was used also increased more than that of KOH. Therefore, the use of KOH rather than NaOH was more effective in the control of particle sizes. An amorphous zirconia nanoparticle was found in 4 h of hydrothermal reaction, but the monoclinic zirconia nanoparticle was found in 8 h and over of hydrothermal reaction, and the width of nanoparticles was slightly slimmed and the length of nanoparticles was slightly extended with increasing reaction time. The smallest particle size was produced at the same synthesis condition when zirconium chloride among the precursors such as zirconium (IV) acetate, zirconium nitrate and zirconium chloride was used.

• Journal of the Korean Ceramic Society
• /
• v.35 no.5
• /
• pp.465-471
• /
• 1998

Lead titanate(PT) and lead magnesium niobate(PMN) ceramic powders were prepared by microwave hy-drothermal method using teflon bomb. Raw materials were Pb(NO3)2 and TiO2 for lead titanate and Pb(NO3)2 Nb2O5 and Mg(NO)3.6H2O for PMN with NaOH as mineralizer in both cases. in lead titanate synthsis rate of microwave hydrothermal method was faster three times than one f conventional hydrothermal methods In lead magnesium niobate synthsis the mixture of perovskite and pyrochlore phases was obtained by single step technique and the PMN was not obtained by double step technique due to low temperature limitation of teflon bomb.

• Macromolecular Research
• /
• v.13 no.6
• /
• pp.499-505
• /
• 2005

Ordered mesoporous materials with a hydrothermally-stable, protozeolitic framework were prepared by exploring the direct conversion of inorganic species based on co-surfactant templating systems. To confer hydrothermal stability on the mesoporous aterials, the organic-inorganic hybrids were heat-treated in strongly basic media. Co-surfactant templating systems of cetyltrimethylammonium bromide [$C_{16}H_{13}(CH_{3})_{3}$NBr, CTAB] with 1,3,5-trim­ethylbenzene (TMB) or a nonionic block copolymer of poly(ethylene oxide )-b-poly(propylene oxide )-b-poly(ethyl­ene oxide) ($EO_{20}PO_{70}EO_{20}$) were employed to improve the hydrothermal stability of the organic-inorganic self-assembly during the solid rearrangement process of the inorganic species. The mesoscopic ordering of the pore structure and geometry was identified by X-ray diffraction, small angle neutron scattering and electron microscopy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.420-421
• /
• 2005

$LiMnPO_4$ particle were prepare by a hydrothermal reaction. The particles prepared by adding polyethylene glycol(PEG) and carbon to the starting reaction solution were fine crystalline in the range of 200-300nm. The discharge capacity of the sample as a lithium secondary battery was $25mAhg^{-1}$ at $0.04mAcm^{-2}$, larger than that of the sample prepared by the hydrothermal method without PEG and carbon.

• Advances in nano research
• /
• v.4 no.1
• /
• pp.1-14
• /
• 2016

Superparamagnetic iron oxide nanoparticles (Nps), composed of magnetite, $Fe_3O_4$, or maghemite, ${\gamma}-Fe_2O_3$, core and biocompatible polymer shell, such as dextran or chitozan, have recently found wide applications in magnetic resonance imaging, contrast enhancement and hyperthermia therapy. For different diagnostic and therapeutic applications, current attempt is focusing on the synthesis and biomedical applications of various ferrite Nps, such as $CoFe_2O_4$ and $MnFe_2O_4$, differing from iron oxide Nps in charge, surface chemistry and magnetic properties. This study is focused on the synthesis of manganese ferrite, $MnFe_2O_4$, Nps by most commonly used chemical way pursuing better control of their size, purity and magnetic properties. Co-precipitation syntheses were performed using aqueous alkaline solutions of Mn(II) and Fe(III) salts and NaOH within a wide pH range using various hydrothermal treatment regimes. Different additives, such as citric acid, cysteine, glicine, polyetylene glycol, triethanolamine, chitosan, etc., were tested on purpose to obtain good yield of pure phase and monodispersed Nps with average size of ${\leq}20nm$. Transmission electron microscopy (TEM), X-ray diffraction, energy dispersive X-ray spectroscopy (EDX), $M\ddot{o}ssbauer$ spectroscopy down to cryogenic temperatures, magnetic measurements and inductively coupled plasma mass spectrometry were employed in this study.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.633-637
• /
• 2023

Recently, with the development of the smart device market, the integration of high-functional devices has increased the heat density, causing overload of the device, and resulting in various problems such as shortened lifespan, performance degradation, and failure. Therefore, research on heat dissipation materials is being actively conducted to realize next-generation electronic products. The heat dissipation material is characterized in that it is easy to dissipate heat due to its high thermal conductivity and minimizes leakage current flowing through the heat dissipation material due to its low electrical conductivity. In this study, flower-shaped Al₂O₃ and BN composites were engineered with a simple hydrothermal synthesis approach, and their thermal conductivity characteristics were compared and evaluated for each synthesis condition for the application to a heat dissipation material. Spherical BN and flower-shaped Al₂O₃ were easily obtained, and SEM/EDS analyses confirmed the uniform presence of BN between the Al₂O₃, and it can be expected that these shapes can affect the thermal conductivity.

• Nano
• /
• v.13 no.11
• /
• pp.1850132.1-1850132.14
• /
• 2018

The direct synthesis of metal-organic frameworks (MOFs) with acidic and basic active sites is challenging due to the introduction of functional groups by post-functionalization method often jeopardize the framework integrity. Herein, we report the direct synthesis of acid-base bifunctional MOFs with tuning acid-base strength. Employing modulated hydrothermal (MHT) approach, microporous MOFs named $UiO-66-NH_2$ was prepared. Through the ring-opening reaction of 1,3-propanesultone with amino group, $UiO-66-NH_2-SO_3H-type$ catalysts can be obtained. The synthesized catalysts were well characterized and their catalytic performances were evaluated in one-pot glucose to 5-HMF conversion. Results revealed the acid-base bi-functional catalyst possessed high activity and excellent stability. This work provides a general and economically viable approach for the large-scale synthesis of acid-base bi-functional MOFs for their potential use in catalysis field.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.3
• /
• pp.95-100
• /
• 2006

Synthesis of the non-swelling property micas was carried out by hydrothermal method. In order to artificially induce the diffusion of ions, a rotating system was attached to the hydrothermal apparatus and by adding 0.7 mm zircon beads, synthesis of the non-swelling property micas could be performed in a low temperature area. The hydrothermal conditions for the preparation of micas were a reaction temperature of $260^{\circ}C$, for 72 hrs, using $1K_2O,\;1Al(OH)_3,\;4Mg(OH)_2\;and\;6SiO_2$ as the starting materials and a 8M-KOH solution as the hydrothermal solvent. The micas obtained under these conditions were a plate shape with a size of $2.89{\mu}m$ and showed a whiteness of over 97 %. Also, through the FT-IR analysis, because the absorption peak of the $Mg_3OH$ vibration was observed at approximately $3700cm^{-1}$, it could be known that it was phlogopite of non-swelling property showing the chemical composition of $KMg_3AlSi_3O_{10}(OH)_2$. This result was very consistent with the EDS analysis where O (41.34 %), Mg (3.88 %), Al (11.45 %), Si (17.62 %) and K (25.71%) elements were detected.