• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.4
• /
• pp.327-329
• /
• 2005

Pb(Zr/sub 0.52/Ti/sub 0.48/)O₃(PZT) thin films were deposited by using a pulsed laser deposition method on a Pt/Ti/SiO₂/Si substrate with (Pb/sub 0.72/La/sub 0.28/)Ti/sub 0.93/O₃ (PLT) buffer and on a Pt/Ti/SiO₂/Si substrate without buffer. These films were annealed in H₂-contained ambient for 30 minutes at the substrate temperature of 400。C to evaluate the forming gas annealing effects. The comparative studies on the ferroelectric properties of these two films were carried out, which are shown that ferroelectric properties, such as remanent polarization didn't change in the case of PLT buffered PZT film while remanent polarization value of PZT film degraded from 20.8 C/㎠ to 7.3 C/㎠. The leakage current became higher in both cases, but that of the more-oriented PZT film had the moderate value of the 10/sup -6/ order of A/㎠. This is mainly because the hydrogen atoms which make the degradation of PZT films cannot infiltrate into the more -oriented PZT film as well as the less-oriented PZT film.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.81-84
• /
• 2010

Al-doped ZnO (AZO) films were prepared by an Ar:$H_2$ gas radio frequency (RF) magnetron sputtering system with a AZO ($2\;wt{\cdot}%\;Al_2O_3$) ceramic target at the low temperature of $100^{\circ}C$ and annealed in hydrogen ambient at the temperature of $300^{\circ}C$. To investigate the influence of the $H_2$ flow ratio on the properties of the AZO films, the $H_2$ flow ratio was changed from 0.5% to 2%. As a result, the AZO films, deposited with a 1% $H_2$ addition, showed a resistivity of $11.7\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$. When the AZO films were annealed at $300^{\circ}C$ for 1 hour in a hydrogen atmosphere, the resistivity decreased from $11.7\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$ to $5.63\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$. The lowest resistivity of $5.63\;{\times}\;10^{-4}{\Omega}{\cdot}cm$ was obtained by adding 1% hydrogen gas to the deposition and annealing process. The X-ray diffraction patterns of all the films showed a preferable growth orientation in the (002) plane. The spectrophotometer measurements showed that the transmittance of 85% was obtained by the film deposited with the $H_2$ flow ratio of 1% at 940 nm for GaAs/GaAlAs LEDs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• Membrane Journal
• /
• v.2 no.1
• /
• pp.21-32
• /
• 1992

Hydrogen-permselective silica membranes were synthesized within tim walls of porous Vycor tubes by chemical vapor depostion of $SiO_2$. Film deposition was carried out using $SiCl_4$ hydrolysis either in the oppm shag reactants or in the one-sided geometry. At temperatures above $600^{\circ}C$ the permeation rate of hydrogen thorough the silica films varied between 0.01 and $025cm^3(STP)/cm^2-min-atm$ depending on the reaction geometry and the $H_2 : N_2$ permeation ratio was about 1000. Permeation rates of both $H_2$ and $N_2$ increased with increasing temperature. The silica membranes produced by one-sided deposition have higher hydrogen permmeation rates than those produced by the opposing reactants geometry although the membranes formed in an opposing reactants geometry were relatively stable during the heat treatment or after exposure to ambient air. These membranes can be applied to high temperature gas separations or membrane reactors once the film deposition process is optimized to get high permeability as well as good stability.

• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.151-154
• /
• 2001

The leakage current behaviors of PLZT capacitors with top electrodes of Pt, Ir, and $IrO_2$ are investigated before and after hydrogen forming gas anneal. The P-E hysteresis and fatigue properties of Pt/PLZT/Pt capacitors are almost recovered after recovery anneal in $O_2$ ambient. The leakage current mechanisms of PLZT capacitors with Pt and $IrO_2$ top electrodes are consistent with space-charge influenced injection model showing the strong time dependence irrespective of annealing conditions. On the other hand, the leakage current behavior of Ir/PLZT/Pt capacitor shows steady state independent of time because IrPb, conducting phase, formed at interface between Ir top and PLZT is a high conduction path. Teh leakage current mechanism of Ir/PLZT/Pt capacitor is consistent with Schottky barrier model.

• Journal of Sensor Science and Technology
• /
• v.22 no.3
• /
• pp.175-180
• /
• 2013

This paper describes the characteristics of cubic silicon carbide (3C-SiC) films grown on a carbonized Si(100) substrate, using hexamethyldisilane (HMDS, $Si_2(CH_3)_6$) as a safe organosilane single precursor in a nonflammable $H_2$/Ar ($H_2$ in Ar) mixture carrier gas by atmospheric pressure chemical vapor deposition (APCVD) at $1280^{\circ}C$. The growth process was performed under various conditions to determine the optimized growth and carbonization condition. Under the optimized condition, grown film has a single crystalline 3C-SiC with well crystallinity, small voids, low residual stress, low carrier concentration, and low RMS. Therefore, the 3C-SiC film on the carbonized Si (100) substrate is suitable to power device and MEMS fields.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.5
• /
• pp.525-544
• /
• 1999

Polycyclic aromatic hydrocarbons (PAH) were one of the first airborne pollutants to be identified as being carcinogenic. This class of compounds is ubiquitous in the urban atmosphere, and has therefore undergone considerable scrutiny for the last three decades. PAH can be formed in any incomplete combustion or high temperature pyrolytic process involving materials containing carbon and hydrogen, such as fossil fuels. In this paper, the literature on the occurrence, ambient levels, and atmospheric fate and behaviour of airbonrne PAH has been reviewed, with a particular emphasis on the role of automobile sources in PAH emissions. Sampling and analytical techniques for the determination of PAH in air have also been examined. In addition, health implications and legislative aspects of human exposure to airborne PAH have been briefly reviewed. Finally, future requirements for better understanding of the atmospheric behaviour of PAH recommended.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.11
• /
• pp.894-901
• /
• 1991

Contact-type linear image sensors have been fabricated by means of RF glow discharge decomposition method of silane and hydrogen mixtures. The dependences of the electrical and optical properties of these sensor on thickness, RF power, substrate temperature and ambient gas pressure have been investigated. the ITO/i-a-Si:H/Al structure film shows photosensitivity of 0.85 and photocurrent to dark current ratio ($I_{ph}/I_{d}$) of 150 at 5V bias voltage under 200${\mu}W/cm^[2}$ red light intensity. Under 200${\mu}W/cm^[2}$ green light intensity, the ratio is 100. In order to investigate photocarrier transport mechanism and to obtain ${\mu}{\gamma}$ product we have measured the I-V characteristics of these sensors favricated with several different deposition parameters under various light sources. The linear inage sensor for document reading has been operated under reverse bias condition with green light source, resulting in ${\mu}{\gamma}$ product of about 1.5$[\times}10^{-9}cm^{2}$/V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.165-165
• /
• 2010

AZO:H films were prepared by RF magnetron sputtering system with a AZO (2wt% $Al_2O_3$) ceramic target at a temperature of $150^{\circ}C$. The annealing treatments were carried out in hydrogen ambient for 1hr at a temperature of $400^{\circ}C$. The AZO:H films were etched with 1 % HCl. The influence of the properties of AZO:H films deposited in various working pressures is investigated. As a result, the AZO:H film deposited in 4mTorr showed excellent electrical property of $\rho=5.036{\times}10^{-4}{\Omega}cm$ and strongly oriented (002) peak. The transmittance in the wavelength of 450nm was above 80%. It can be used as front electrode for increasing efficiency of GaN LED.

• Journal of Sensor Science and Technology
• /
• v.20 no.6
• /
• pp.428-433
• /
• 2011

We report on the building of a micro sensor array based on typical semiconductor fabrication processes aimed at monitoring selectively a specific gas in ambient of other gases. Chemical sensors can be applied for an electronic nose and/or robots using this technique. Microsensor array was fabricated on the same chip using 0.6${\mu}m$ CMOS technology, and unique gas sensing patterns were obtained by principal component analysis from the array. $SnO_2$/Pt sensor for CO gas showed a high selectivity to buthane gas and humidity. $SnO_2$ sensor for hydrogen gas, however, showed a low selectivity to CO and buthane gas. We can obtain more distinguishable patterns that provide the small sensing deviation(the high seletivity) toward a given analyte in the response space than in the chemical space through the specific parameterization of raw data for chemical image formation.