• Journal of the Korean Magnetics Society
• /
• v.16 no.3
• /
• pp.157-162
• /
• 2006

In this study, a high sensitive giant magnetoresistance-spin valve (GMR-SV) bio-sensing device with high linearity and very low hysteresis was fabricated by photolithography and ion beam deposition sputtering system. Detection of the Fe-hemoglobin inside in a red blood and magnetic nanoparticles using the GMR-SV bio-sensing device was investigated. Here a human's red blood includes hemoglobin, and the nanoparticles are the Co-ferrite magnetic particles coated with a shell of amorphous silica which the average size of the water-soluble bare cobalt nanoparticles was about 9 nm with total size of about 50 nm. When 1 mA sensing current was applied to the current electrode in the patterned active GMR-SV devices with areas of $5x10{\mu}m^2 $ and $2x6{\mu}m^2 $, the output signals of the GMRSV sensor were about 100 mV and 14 mV, respectively. In addition, the maximum sensitivity of the fabricated GMR-SV sensor was about $0.1{\sim}0.8%/Oe$. The magnitude of output voltage signals was obtained from four-probe magnetoresistive measured system, and the picture of real-time motion images was monitored by an optical microscope. Even one drop of human blood and nanopartices in distilled water were found to be enough for detecting and analyzing their signals clearly.

• Korean Journal of Agricultural Science
• /
• v.42 no.1
• /
• pp.63-71
• /
• 2015

Path planning is an essential part for traveling and mowing of autonomous lawn mower tractors. Objectives of the paper were to analyze operation patterns by a skilled farmer, to extract and optimize waypoints, and to demonstrate generation of formatted planned path for autonomous lawn mower tractors. A 27-HP mower tractor was operated by a skilled farmer on grass fields. To measure tractor travel and operation characteristics, an RTK-GPS antenna with a 6-cm RMS error, an inertia motion sensing unit, a gyro compass, a wheel angle sensor, and a mower on/off sensor were mounted on the mower tractor, and all the data were collected at a 10-Hz rate. All the sensor data were transferred through a software program to show the status immediately on the notebook. Planned path was generated using the program parameter settings, mileage and time calculations, and the travel path was plotted using developed software. Based on the human operation patterns, path planning algorithm was suggested for autonomous mower tractor. Finally path generation was demonstrated in a formatted file and graphic display. After optimizing the path planning, a decrease in distance about 13% and saving of the working time about 30% was achieved. Field test data showed some overlap, especially in the turning areas. Results of the study would be useful to implement an autonomous mower tractor, but further research needs to improve the performance.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.6
• /
• pp.921-926
• /
• 2022

Sugar solutions (5%, 10%, 15% and 20%) were tested by seven sensors of Astree E-Tongue for selecting a sensor for sweetness. NMS sensor was chosen as a sensor for sweetness among two sensors (PKS and NMS sensors selected in first stage) by considering precision, linearity and accuracy. Sugar, fructose, glucose and xylitol (5%, 10% and 15%) were tested by E-tongue. The principal component analysis (PCA) result by E-Tongue with seven sensors at 5% concentration level of four sweetners was not satisfactory (Discrimination index was -0.1). On the other hand, the relative NMS sensor response values were derived as 1.08 (fructose), 0.99 (glucose) and 1.00 (xylitol) comparing to sugar. Only the E-Tongue relative glucose response 0.99 was different from 0.5~0.75 of the relative sweetness range reported as the human sensory test results. Considering the excellent precision (%RSD, 1.53~3.64%) of E-Tongue using NMS single sensor for three types of sweeteners compared to sugar in the concentration range of 5% to 15%, replacing sensory test of sweetened beverages by E-Tongue might be possible for new product development and quality control.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.754-761
• /
• 2008

As the automobile industry and technologies are developed, driver's tend to more concern about service matters than mechanical matters. For this reason, interests about recognition of human knowledge and emotion to make safe and convenient driving environment for driver are increasing more and more. recognition of human knowledge and emotion are emotion engineering technology which has been studied since the late 1980s to provide people with human-friendly services. Emotion engineering technology analyzes people's emotion through their faces, voices and gestures, so if we use this technology for automobile, we can supply drivels with various kinds of service for each driver's situation and help them drive safely. Furthermore, we can prevent accidents which are caused by careless driving or dozing off while driving by recognizing driver's gestures. the purpose of this paper is to develop a system which can recognize states of driver's emotion and attention for safe driving. First of all, we detect a signals of driver's emotion by using bio-motion signals, sleepiness and attention, and then we build several types of databases. by analyzing this databases, we find some special features about drivers' emotion, sleepiness and attention, and fuse the results through Multi-Modal method so that it is possible to develop the system.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1474-1475
• /
• 2008

본 논문에서는 nanoporous Pt (Platinum) 전극을 이용한 무효소 혈당센서의 생체 적합성 및 전류응답 특성 향상을 위해 다양한 패키징 방법이 제안되었다. 생체적합성을 갖는 Nafion 멤브레인을 dipping, spin coating, chemical bonding 방법으로 패키징 한 후, 다양한 글루코오스 농도의 혈장, 전혈에서 특성을 분석, 비교하였다. 단백질 등이 포함되지 않은 환경에서 spin coating 방법으로 패키징한 센서의 전류응답 특성은 가장 좋았지만, 혈장 및 전혈에서는 dipping, chemical bonding 방법으로 패키징한 센서의 전류응답 특성에 미치지 못했다. Nafion film을 센서와 chemical bonding한 센서의 혈장에서 sensitivity 는 0.32 ${\mu}A/mM{\cdot}cm^2$ 이었다. 한편, 전혈에서 bare 센서가 급격한 bio-fouling 현상을 보이는 반면 패키징한 센서는 글루코오스 농도에 따라 일정한 전류변화를 보였다. 이는 Nafion을 이용하여 패키징한 무효소 혈당 센서가 생체환경에 적합할 뿐 아니라 생체이식형 및 연속 측정 가능한 시스템에 적용 가능함을 보여준다.

• Journal of the Ergonomics Society of Korea
• /
• v.27 no.4
• /
• pp.95-101
• /
• 2008

This research is to develop PPG filtering method for respiration measurement in U-Health Care system. Respiration rate was determined by filtering PPG and analyzing its spectrum. Optimal filter of PPG has been selected to get respiration by testing 120 sets of experiment data using 700 filtering cases. As a result, 2nd order Bessel-filter that used band-pass cutoff frequency at 0.175~0.4Hz with second order was good at developing respiration signal. Respiration signal in time domain could be continuously analyzed by converting frequency domain using spectrum analysis. 24 seconds has been found to be optimal time duration of collecting PPG data for determining respiration. Therefore, this study was successful of getting not only heart activity but also respiration by only PPG. Minimal invasive measurement obtaining multi-bio information by one sensor can be expected to apply to U-Health Care and human computer interaction.

• Journal of Sensor Science and Technology
• /
• v.21 no.2
• /
• pp.156-166
• /
• 2012

Over the past 15 years productive BCI research programs have arisen. Current mainstream EEG electrode setups permit efficient recordings but most of electrodes has the disadventages of need for skin preparation and gel application to correctly record signals. The new gel-free probe was adapted for EEG recording and it can be fixed to the scalp with the micro needle without neuro-gel. It use standard EEG cap for wearing electrodes on scalp so it is compatible with standard EEG electrodes. A comparison between electrode characteristics is achieved by performing simultaneous recordings with the gel electrodes and gel-free probe placed in parallel scalp positions on the same anatomical regions. The quality of EEG recordings for all two types of experimental conditions is similar for gel-electrodes and gel-free probe. Subjects also reported not having special tactile sensations associated with wearing of gel-free probes. According to our results, it is expected that gel-free probe can be adapted to BCI, BMI(Brain Machine Interface), HMI(Human Machine Interface) because of its simple application and comfortable wearing process.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.47 no.1
• /
• pp.1-16
• /
• 2023

The smart fashion industry is showing steady growth worldwide, which will create new value throughout the fashion industry and become an essential element for efficient lifestyles. This study attempted to examine the development trend of smart fashion products from a design perspective and present the direction of design as a fashion item incorporating smart technology from a functional perspective. For this purpose, the category of portable smart fashion and the characteristics of the research object were considered through current status survey and previous research review. Among smart fashion, accessories and clothing/fabric products that have been released thus far that apply portable fashion design principles are selected and its characteristics are analyzed. In addition, function keywords were extracted based on the product description provided by the manufacturer and the function-oriented types were classified to identify each type's design characteristics. Therefore, the area receiving the signal and the sensor size should be considered, as should the fashion accessory type that combines various materials and colors. The clothing/textile type requires a design that mainly focuses on functions related to bio-signal interactions.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.4
• /
• pp.1-9
• /
• 2012

As we are turnning into the aged society, accidents by falling down are increasing in the aged people's group. In this paper, we design the system with the 3-Axis acceleration sensor which is composed by a single chip. The body activity signal is measured with the signal detector and RF communicator in this proposed system and the and falling by the entering signal pattern analysis with 3-Axis acceleration sensor. For the RF communication, we are using nRF24L01p and 8bits ATmega uC for the processor. The error of energy expenditure estimation between motor driven treadmill and proposed a body activity module was 7.8% respectively. Human activities and falling is monitored according to analyze and judge the critical value of the Signal Vector. as falled down if they don't turn off the alarm after specific period and the aged person's after falling down activities are their position and more.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4C
• /
• pp.329-337
• /
• 2012

Capsule Endoscope(CE) is a capsule-shaped electronic device which can examine the lesions in digestive tract of human body. Recently the medical procedure using capsule endoscope is receiving great attention to both doctors and patients, since the conventional push-typed endoscope using cables brings great pain and fear to the patients. The technique was firstly available in 2000 and is based on a convergence techniques among BT(Bio Technology), IT(Information Technology), and NT(Nano Technology). The device consists of an optical parts including LEDs(Light Emitting Diodes), an image sensor, a communication module and a power module. Capsule endoscope is the embodiment of the state-of-the art technology and requires key technologies in the various engineering fields. Therefore, in this paper, we introduce the composition of the capsule endoscope system, and compare the communication method between RF(Radio Frequency) communication and HBC(Human Body Communication), which are typically used for data transmission in the capsule endoscope. Furthermore, we analyze the specification of commercialized capsule endoscopes and present the future developments and technical challenges.