• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.245-259
• /
• 2003

This paper deals with an Umbrealla Arch Reinforcement Method (UARM) in tunnelling. It is known that the mechanism of the reinforcement system is too complex to be simulated in existent finite element (FE) frameworks when considering its complex geometry of pipe arrangements and contribution of each component of the reinforcement to reinforcing effect. In this study a 3-D elastoplastic FE procedure is, therefore, proposed by introducing homogenisation technique, which is used to define mathematically elastic as well as elastoplastic characteristics of a reinforced ground material as a composite. A number of practical suggestions are addressed considering staged constructions of tunnels. For illustrative purposes, a series of parametric studies are undertaken and anisotropic characteristics of the reinforced ground as well as effects of the reinforcement on tunnel convergences are investigated. It is found that the reinforced ground material defined in homogenisation framework has its mechanical characteristics reasonably representing inherent geometrical and quantitative characteristics of each of constituents.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.2
• /
• pp.248-260
• /
• 2021

Cobalt-chromium alloys are used to fabricate various dental prostheses, and have advantages of low cost and excellent mechanical properties compared to other alloys. Recently, selective laser melting, which is an additive manufacturing method, has been used to overcome the disadvantages of the conventional fabrication method. A local rapid heating and cooling process of selective laser melting induces fine microstructures, grain refinement, and reduction of porosities of the alloys. Therefore, it can improve mechanical properties compared to the alloys fabricated by the conventional method. On the other hand, layering process and rapid heating and cooling cause accumulation of a large amount of residual stresses that can adversely affect the mechanical properties. A heat treatment for removing residual stresses through recovery and recrystallization process caused complicated changes in mechanical properties induced by phase transformation, precipitate and homogenization of the microstructures. The purpose of this review was to compare the manufacturing methods of Co-Cr alloys and to investigate the characteristics of Co-Cr alloys fabricated by selective laser melting.

• KSBB Journal
• /
• v.16 no.5
• /
• pp.523-525
• /
• 2001

Curdlan is one biopolymer composed of ${\beta}$1,3-glucan and dissolved in a alkali solution but formed salt under neutral or acid condition. It was produced by Agrobactrium species and the separation process is necessary to make pure curdlan from the culture broth. The pH swing separation method was as feasible separation process using solubility changes with the pH difference. however, this method requires a lot of acid and alkali solution also produces a lot of waste. Therefore, an efficient process which could save energy and minimize toxic waste was developed. A density gradient separation process was developed in this research. High density sucrose solution was used as a separation agent. Curdlan was separated from the culture broth when the density of the sucrose solution was 1.15 g/L. Since the curdlan was produced on the surface of cell wall. the pre-treatment of culture broth was necessary. Curdlan recovery yield was increased up to 83% with the homogenization of the culture broth and further increased up to 87% with the treatment of alkai-acid solution.

• The Journal of the Korean Society for Microbiology
• /
• v.7 no.1
• /
• pp.21-27
• /
• 1972

A simple and effective procedure is described for semi-purification of viable Myco. leprae from biopsied lepromatous nodules by trypsinization and high-speed centrifugation. An unique characteristic of this method is a complete omission of conventional grinding or homogenization of minced lepromatous tissues prior to purification. Inoculation of trypsin-purified preparation of Myco. leprae into foot pads and ear lobes of Korean chipmunk(Tamias sibiricus asiaticus, Gmelin) resulted in apparent increases in total number of acid-fast bacilli per inoculated tissue 8 and 12 months after inoculation.

• Journal of Pharmaceutical Investigation
• /
• v.33 no.4
• /
• pp.319-322
• /
• 2003

Many studies have been attempted to overcome the problems of paclitaxel related to the extremely low aqueous solubility of paclitaxel and the unexpected side-effects caused by $Cremophor^{\circledR}$ EL in a commercial paclitaxel formulation, $Taxol^{\circledR}$. In order to formulate a new delivery system suitable for intravenous administration without toxic excipients, in this study, paclitaxel was incorporated into solid lipid nanoparticles (Px-SLN) by hot homogenization technique using a microfluidizer. Particle size and zeta potential were measured by a Zetasizer. In vitro drug release experiment was performed by a dialysis diffusion method. Each Px-SLN or $Taxol^{\circledR}$ was intravenously administered to the male Sprague-Dawley rats at a dose of 5 mg/kg as paclitaxel. Blood samples were deproteinated with acetonitrile and assayed for paclitaxel by the validated HPLC/MS/MS method. Mean particle size and zeta potential were measured as 72.1 nm (< Polydispersity 0.3) and -41.5 mV, respectively. The content of paclitaxel in SLN was 1.42 mg/ml and the drug loading efficiency was $71.2{\pm}4.3%$. The $AUC_t$ of Px-SLN was 3.4-fold greater than that of $Taxol^{\circledR}$. The Px-SLN might be a promising candidate for an alternative formulation for the parenteral delivery of paclitaxel.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.41-48
• /
• 2012

A numerical analysis of thermal stratification in the upper plenum of the MONJU fast breeder reactor was performed. Calculations were performed for a 1/6 simplified model of the MONJU reactor using the commercial code, CFX-13. To better resolve the geometrically complex upper core structure of the MONJU reactor, the porous media approach was adopted for the simulation. First, a steady state solution was obtained and the transient solutions were then obtained for the turbine trip test conducted in December 1995. The time dependent inlet conditions for the mass flow rate and temperature were provided by JAEA. Good agreement with the experimental data was observed for steady state solution. The numerical solution of the transient analysis shows the formation of thermal stratification within the upper plenum of the reactor vessel during the turbine trip test. The temporal variations of temperature were predicted accurately by the present method in the initial rapid coastdown period (~300 seconds). However, transient numerical solutions show a faster thermal mixing than that observed in the experiment after the initial coastdown period. A nearly homogenization of the temperature field in the upper plenum is predicted after about 900 seconds, which is a much shorter-term thermal stratification than the experimental data indicates. This discrepancy is due to the shortcoming of the turbulence models available in the CFX-13 code for a natural convection flow with thermal stratification.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.412-418
• /
• 2011

Reliability-based Topology optimization(RBTO) is to get an optimal design satisfying uncertainties of design variables. Although RBTO based on homogenization and density distribution method has been done, RBTO based on BESO has not been reported yet. This study presents a reliability-based topology optimization(RBTO) using bi-directional evolutionary structural optimization(BESO). Topology optimization is formulated as volume minimization problem with probabilistic displacement constraint. Young's modulus, external load and thickness are considered as uncertain variables. In order to compute reliability index, four methods, i.e., RIA, PMA, SLSV and ADL(adaptive-loop), are used. Reliability-based topology optimization design process is conducted to obtain optimal topology satisfying allowable displacement and target reliability index with the above four methods, and then each result is compared with respect to numerical stability and computing time. The results of this study show that the RBTO based on BESO using the four methods can effectively be applied for topology optimization. And it was confirmed that DLSV and ADL had better numerical efficiency than SLSV. ADL and SLSV had better time cost than DLSV. Consequently, ADL method showed the best time efficiency and good numerical stability.

• Computers and Concrete
• /
• v.26 no.2
• /
• pp.127-136
• /
• 2020

There is an inherent randomness for concrete microstructure even with the same manufacturing process. Meanwhile, the concrete material under the aqueous environment is usually not fully saturated by water. This study aimed to develop a stochastic micromechanical framework to investigate the probabilistic behavior of the unsaturated concrete from microscale level. The material is represented as a multiphase composite composed of the water, the pores and the intrinsic concrete (made up by the mortar, the coarse aggregates and their interfaces). The differential scheme based two-level micromechanical homogenization scheme is presented to quantitatively predict the concrete's effective properties. By modeling the volume fractions and properties of the constituents as stochastic, we extend the deterministic framework to stochastic to incorporate the material's inherent randomness. Monte Carlo simulations are adopted to reach the different order moments of the effective properties. A distribution-free method is employed to get the unbiased probability density function based on the maximum entropy principle. Numerical examples including limited experimental validations, comparisons with existing micromechanical models, commonly used probability density functions and the direct Monte Carlo simulations indicate that the proposed models provide an accurate and computationally efficient framework in characterizing the material's effective properties. Finally, the effects of the saturation degrees and the pore shapes on the concrete macroscopic probabilistic behaviors are investigated based on our proposed stochastic micromechanical framework.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.602-611
• /
• 2013

We have investigated the influence of system composition and preparation conditions on the particle size of vitamin E acetate (VE)-loaded nanoemulsions prepared by PIC(phase inversion composition) emulsification. This method relies on the formation of very fine oil droplets when water is added to oil/surfactant mixture. The oil-to-emulsion ratio content was kept constant (5 wt.%) while the surfactant-to-oil ratio (%SOR) was varied from 50 to 200 %. Oil phase composition (vitamin E to medium chain ester ratio, %VOR) had an effect on particle size, with the smallest droplets being formed below 60 % of VOR. Food-grade non-ionic surfactants (Tween 80 and Span 80) were used as an emulsifier. The effect of f on the droplet size distribution has been studied. In our system, the droplet volume fraction, given by the oil volume fraction plus the surfactant volume fraction, was varied from 0.1 to 0.3. The droplet diameter remains less than 350 nm when O/S is fixed at 1:1. The droplet size increases gradually as the increasing the volume fraction. Particle size could also be reduced by increasing the temperature when water was added to oil/surfactant mixture. By optimizing system composition and homogenization conditions we were able to form VE-loaded nanoemulsions with small mean droplet diameters (d < 50 nm). The PIC emulsification method therefore has great potential for forming nanoemulsion-based delivery systems for food, personal care, and pharmaceutical applications.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2290-2294
• /
• 2014

For the present study, rhEGF was encapsulated into solid lipid nanoparticles (SLNs). The SLNs were prepared by the $W_1/O/W_2$ double emulsification method combined with the high pressure homogenization method and the physical properties such as particle size, zeta-potential and encapsulation efficiency were measured. The overall particle morphology of SLNs was investigated using a transmission electron microscopy (TEM). The percutaneous skin permeation and accumulation property of rhEGF was evaluated using Franz diffusion cell system along with confocal laser scanning microscopy (CLSM). The mean particle size of rhEGF-loaded SLNs was $104.00{\pm}3.99nm$ and the zeta-potential value was in the range of -$36.99{\pm}0.54mV$, providing a good colloidal stability. The TEM image revealed a spherical shape of SLNs about 100 nm and the encapsulation efficiency was $18.47{\pm}0.22%$. The skin accumulation of rhEGF was enhanced by SLNs. CLSM image analysis provided that the rhEGF rat skin accumulation is facilitated by an entry of SLNs through the pores of skin.