• 한국항행학회논문지
• /
• 제21권6호
• /
• pp.651-658
• /
• 2017

방사선이 존재하는 환경에서 무색, 무미, 무촉의 방사선을 검출하기 위한 계측장비는 매우 중요하며 그동안 방사선 계측장비의 개발에 대한 많은 연구들이 있었다. 특히 방사선을 검출한 이후 측정된 검출신호를 손실 없이 효율적으로 처리하기 위해 검출된 미세전류를 전압형태로 정형하고, 이를 정확하게 판독하는 신호처리 부분은 매우 중요하다. 검출된 방사선 신호파형을 판독할 때, 지금까지는 신호의 전압파형을 짧은 시간 동안 일정한 값으로 유지시켜 파형의 크기를 판독한 후, 그 전기적인 값을 방전하고 다음 파형에 대비하는 피크홀드방식을 사용하였다. 이 연구에서는 방사선 검출기에서 측정된 검출신호 전압파형의 판독을 피크홀드방식이 아닌, 전압신호의 파고 정점에 이르는 시간을 포착하여 그 값을 직접 판독하는 방식을 제안한다. 이 방식에 의하면 전압 파고를 일정한 시간동안 유지하거나, 유지된 전압 파고를 초기상태로 만드는 복잡한 과정을 거치지 않고 검출된 방사선 신호를 정확하게 판독할 수 있다는 장점을 가지며, 실제 시뮬레이션을 통하여 이를 검증하였다.

• 한국통신학회논문지
• /
• 제28권5A호
• /
• pp.294-304
• /
• 2003

셀룰러 CDMA 시스템에서 보다 효과적인 소프트웨어 다운로드가 되기 위해, 영역 기반 세션수락제어 기법이 제안된다. 제안 방식에서 기지국은 단말이 셀의 기지국 근처에 위치할 때만 세션 시작을 허용한다. 단말의 위치가 셀의 기지국 근처이면 소프트웨어 다운로드 요구를 허용하고, 셀의 경계에 위치한 경우는, 셀의 근처로 올 때까지 기다려서, 소프트웨어 다운로드를 시도하도록 함으로서, 소프트웨어 다운로드 중 셀간 핸드오프가 일어나는 빈도를 줄여, 핸드오프 세션의 강제절단확률을 줄이는 방식이다. 세션지속시간의 분포함수로서 지수분포와 Pareto 분포를 고려하여 핸드오프 빈도, 평균 채널점유시간, 세션 블록킹 확률, 핸드오프 세션의 강제 절단 확률 관점에서 성능을 분석하였다. 성능분석 결과 단말 이동속도, 세션 요구 허용 지역의 크기, 핸드오프 전용 채널 수 등의 트래픽 특성에 따라 다르지만, 분석을 위해 가정한 파라미터 값을 기준으로, 기존 방식에 비해 30 ～ 250% 정도의 핸드오프 빈도를 줄일 수 있게 된다. 또한 신규세션의 블록킹 확률은 5 ~ 20% 정도 줄이지만, 핸드오프세션의 강제절단률은 35% ~ 220%까지 줄일 수 있게 됨을 알 수 있다.

• 한국수자원학회논문집
• /
• 제42권10호
• /
• pp.809-824
• /
• 2009

한정된 기간의 짧은 유출량 기록을 갖는 댐 유역에서의 수자원 시스템 거동예측은 수문학적 지속성여부에 대한 판단이 선행 되어야 하며 가용한 시계열자료에 대한 추계학적 분석을 통하여 실시하여야 한다. 본 연구에서는 계절형 ARIMA모형을 통하여 안동댐 유역의 강우량, 증발량 및 유출량 시계열자료로 월별 수문시스템 거동을 예측하였으며, 예측된 결과를 토대로 TANK모형과 ARIMA+TANK결합모형에 의한 장기유출모의를 실시하였다. 분석결과 관측자료의 특성을 비교적 잘 반영 하였으며, 댐 유입량 예측을 위한 추계학적 결합모형의 적용가능성을 검토하였다. 이는 상대적으로 유출량자료의 보유년한이 짧은 대상유역의 시계열 수문인자 예측을 통한 유출모의의 적용으로 수자원의 중 장기 전략수립에 도움이 되리라 사료된다.

• 한국세라믹학회지
• /
• 제54권4호
• /
• pp.285-291
• /
• 2017

This study investigated the effects of grain size and phase constitution on the mechanical properties of $3Y-ZrO_2$ by varying the sintering conditions. The raw powder prepared by a low-cost wet milling using the coarse solid oxide powders was sintered by both pressureless sintering and hot-pressing, respectively. As increasing holding time at $1450^{\circ}C$ for pressureless sintering, it promoted the microstructural coarsening of matrix grains and the phase transformation to tetragonal phase, whereas the bimodal microstructure embedded with abnormal $cubic-ZrO_2$ grains was observed regardless of sintering time. On the other hand, the specimens hot-pressed at $1300^{\circ}C$ for 2 h reached ~ 97% of relative density with homogeneous fine microstructure and mixed phase constitution. It was found that the proportion of untransformed monoclinic zirconia had the most adverse effect on the biaxial strength compared to the impacts of grain size and density. The pressureless sintering of the low-cost powder for prolonged sintering time to 8 h led to a decent combination of mechanical properties ($H_V=13.2GPa$, $K_{IC}=8.16MPa{\cdot}m^{1/2}$, ${\sigma}=981MPa$).

• 대한간호학회지
• /
• 제30권1호
• /
• pp.225-239
• /
• 2000

This study is a research of conceptual development to find the factors of presence. The concept and the definition of presence received from literary review. On the basis of these findings, we formulate the contents of presence through structured interview guide composed of open-ended questionnaire which included the frequency, attitude, and posture. We selected 104 samples who are the patients, doctors, nurses, and other health providers. And then the contents of presence were established after integrating the formulated contents and putting them in order. The categorizing of the presence was made after discussing with specialist in this field. By using the selected contents, we made 25 statements of presence which were categorized into three factors. The results were as follows: 1. The definition of presence is being with at the same time and space, making attention with openness, and the therapeutic interaction with empathy. 2. The contents of presence through personal interviews are The time required is 5 minutes(46.15%), 2-3 minutes(34.61%), and 10 minutes (15.38%) respectively. The frequency of visiting is 3 times(39.20%), every time(23.07%), and more than 5 times(20.19%) respectively. \circled2 In case of being with nurse is having pain(39.42%), suffering trouble or severe fear(9.61%), feeling discomfort(8.65%), taking care of wound(7.69%), and other unfavorable symptoms(6.73%) respectively. \circled3 The posture being with nurse is depends on the situations(63.46%), sitting(26.92%), and standing(9.61%) respectively. Eye contact with nurse is face to face(78.84%), depends on the situations(20.19%), and not face to face(0.96%) respectively. \circled4 The attitudes of comfort are explaining about disease(23.07%), holding on hands (14.42%), touching on the suffering parts (11.53%), and unconditionally being with(7.69%) respectively. \circled5 Nurses' caring actions are kindness (27.88%), replying to the question (12.50%), smiling(10.57%), bright appearances (8.65%), and right and quick treatment(8.65%) respectively. \circled6 The effects of being with are peaceful mind(58.65%), quick recovery(13.46%), and decrease in fear(12.50%) respectively. \circled7 The attitudes of being with are listening (11.53%), recognition(8.65%), talking about discomfort(8.65%), and answering kindly (7.69%) respectively. 3. From the analysis of presence factors, 25 statements and 3 categorized factors are presented.

• 방송공학회논문지
• /
• 제7권1호
• /
• pp.2-9
• /
• 2002

최근에 TV 방송에서 가상스튜디오나 가상캐릭터와 같은 가상현실(VR: Virtual Reality) 기술이 자주 사용되고 있으며 증강현실 (AR: Augmented Reality) 기술에 대한 관심도 높아지고 있다. 본 논문에서는 증강현실 기술을 방송에 응용한 가상스크린 시스템에 대해 소개한다. 가상스크린 시스템은 움직이는 색상패턴 패널을 추적하여 실시간으로 그 위에 동영상을 합성하는 증강영상 시스템이다. KBS 기술연구소에서는 가상스크린 시스템을 개발하고 'K-비전'이라 이름지었다. 이 시스템은 사용자가 들고 움직이는 패널에 동영상이나 그래픽 영상 등을 보여줄 수 있는데, 보여지는 모든 영상은 카메라의 움직임과 패널의 움직임에 따라 정확하게 입혀진다. 패널 추적을 위하여 블럽 분석(blob analysis)이나 특징 추적(feature tracking)과 같은 영상처리 기술을 이용한다. K-비전은 모든 타입의 카메라와 사용 가능하며. 특별한 부가장치가 필요하지 않다. 센서를 부착하지 않아도 되고. 캘리브레이션(calibration) 과정 또한 필요하지 않다. K-비전은 선거개표 방송. 다큐멘터리, 오락 프로그램 등 생방송 프로그램에서 활용한다.

• Journal of Welding and Joining
• /
• 제32권2호
• /
• pp.29-36
• /
• 2014

Recently, in order to enhance the function and usefulness of products, cladding of dissimilar materials that maximizes the performance of the material is being widely used in all areas of industry as an important process. Clad steel plate, produced by cladding stainless steel plate, an anticorrosive material, on carbon steel plate, is being used to produce pressure vessels. Stainless steel plate has good corrosion resistance, and carbon steel plate has good rigidity and strength; clad steel can satisfy all of these qualities at once. This study aims to find the ${\delta}$-ferrite behavior, mechanical properties, structure change, integrity and reliability of clad steel weld on hot rolled steel plates. For this purpose, multi-layer welding, repair welding and post weld heat treatment were implemented according to welding procedure specifications (WPS). In order to observe the mechanical properties and toughness of clad steel weld zone, post weld heat treatment was carried out according to ASME Sec. VIII Div.1 UW-40 procedure for post weld heat treatment. With heat treatment at $625^{\circ}C$, the hold time was used as the process variable, increased by intervals that were doubled each time, from 80 to 1,280 min. The structure of weld part was typical cast structure; localized primary austenite areas appeared near central vermicular ferrite and fusion line. The heat affected zone showed rough austenite structure created by the weld heat input. Due to annealing effects of heat treatment, the mechanical properties (tensile strength, hardness, impact value) of the heat affected area tended to decrease. From the results of this study, it is possible to conclude the integrity of clad steel welds is not affected much in field welding, repair welding, multi-layer welding, post weld heat treatment, etc.

• 기술사
• /
• 제1권1호
• /
• pp.18-25
• /
• 1968

Higher yield in rice paddies is greatly dependent on adequately balanced and timely supply of water. A majority of rice paddy in Korea is generally irrigated by rainfall, but in many cases it has to be supplemented by artificial irrigation for optimum rice culture. Although the water requirement of rice plant is for higher Than that of athec crops, submerged condition of rice paddy is not Necessarily required. The moisture requirement of rice plant varies with its growing stages, and it is possible to increase the irrigation efficiency through reduction of water loss due to percolation in rice paddies. An experimental plots were set up by means of sandomized block design with three duplication; (a) All time submerged, (b) Economically controlled, and (c) Extremely controlled. Three different irrigation periods Were (a) Initial sage, (b) Inter-stage, and (c) Yast stage. The topsoil of the three plots were excavated to the depth of 30 cm and then compacted with clay of 6 cm thickness. There after, they were piled up with the excavated top soils, leveled and cored with clay of 6 cm thickness around footpath in order to prevent leakage. The results obtained from the experiments are as follows, 1. There is no difference among the three experiments plots in terms of physical and chemical conditions, soil properties, and other characteristics. 2. Culm length and ear length are not affected by different irrigation methods. 3. There is no difference in the mature rate and 1, 000 grain weight of rice for the three plots. 4. The control plot which was irrigated every three days shows an increased yield over the all the time submerged plot by 17.8 percent. 5. The clay lined plot whose water holding capacity was held 5 days long, needs only to be irrigated every 7 days. 6. The clay lined plot shows an increased yield over the untreated plot ; over all-the-time submerged plot by 18 percent ; extremely controlled plot by 18 percent, and economically controlled plot by 33 percent. 7. It may be saved in water requirement about one Thirds.

• The Korean Journal of Physiology
• /
• 제24권2호
• /
• pp.377-388
• /
• 1990

Ca movements during the late plateau phase in rabbit atrium implicate Na-Ca exchange. In single atrial cells isolated from the rabbit the properties of the inward current of Na-Ca exchange were investigated using the whole cell voltage clamp technique. The inward currents were recorded during repolarization following brief 2 ms depolarizing pulse to +40 mV from a holding potential of -70 mV. Followings are the results obtained: 1) When stimulated every 30 sec, the inward currents were activated and reached peak values $6{\sim}12\;ms$ after the beginning of depolarizing pulse. The mean current amplitude was 342 pA/cell. 2) The current decayed spontaneously from the peak activation and the timecourse of the relaxation showed two different phases: fast and slow phase. 3) The recovery of the inward current was tested by paired pulse of various interval. The peak current recovered exponentialy with a time course similar to that of Ca current recovery. 4) Relaxation timecourse was also affected by pulse interval and time constant was reduced almost linearly according to the decrease of pulse interval between 30 sec and 1 sec. 5) The peak inward current was increased by long prepulse stimulation, Bay K, isoprenaline or c-AMP. 6) The relaxation time constant of the inward current was prolonged by Bay K or c-AMP, and shortened by isoprenaline. From the above results, it could be concluded that increase of the calcium current potentiates and prolongs intracellular calcium transients, while shortening of the timecourse by isoprenaline or short interval stimulations might be due to the facilitation of Ca uptake by SR.

• Journal of Welding and Joining
• /
• 제23권6호
• /
• pp.99-105
• /
• 2005

The mixing ratio effect of the GTD-111(base metal) powder and the GNI-3 (Ni-l4Cr-9.5Co-3.5Al-2.5B) powder on TLP(Transient Liquid Phase) bonding phenomena and mechanism was investigated. At the mixing ratio of the base metal powder under $50wt\%$, the base metal powders fully melted at the initial time and a large amount of the base metal near the bonded interlayer was dissolved by liquid inter metal. Liquid insert metal was eliminated by isothermal solidification which was controlled by the diffusion of B into the base metal. The solid phases in the bonded interlayer grew epitaxially from the base metal near the bonded interlayer inward the insert metal during the isothermal solidification. The number of grain boundaries farmed at the bonded interlayer corresponded with those of base metal. At the mixing ratio above $60wt\%$, the base metal powder melted only at the surface of the powder and the amount of the base metal dissolution was also less at the initial time. Nuclear of solids firmed not only from the base metal near the bonded interlayer but also from the remained base metal powder in the bonded interlayer. Finally, the polycrystal in the bonded interlayer was formed when the isothermal solidification finished. When the isothermal solidification was finished, the contents of the elements in the boned interlayer were approximately equal to those of the base metal. Cr-W borides and Cr-W-Ta-Ti borides formed in the base metal near the bonded interlayer. And these borides decreased with the increasing of holding time.