• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.1
• /
• pp.35-42
• /
• 2010

The rapid economic development induced the massive road constructions, becoming bigger and high-speed of the vehicles. However, it brings lots of social problems, such as air pollutions, traffic noise and vibration. Special concrete block for the base course of asphalt pavement is needed to decrease traffic noise such as tire's explosive and vehicles sound, applying Helmholtz Resonators theory to asphalt pavement. If it is applied to the area where it happens considerable noise such as a junction, the street of a housing complex and a residential street, it is one of considerable method to solve the social requirements of noise problem. This research examines couple of laboratory tests for the sound absorption effect of the concrete block and the base concrete block. There are specimens which is fixed hall-size, space, depth as the condition of this research, and these are analysed of noise decrease effect using different condition of the first noise of each vehicle. As a result of analysis data according to vehicle noise volume, measurement distance, a form and size of the hall using the base concrete block, the use of special concrete base showed a good alternative solution for decreasing traffic noise level, from 4 dB to 9 dB.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.3
• /
• pp.78-88
• /
• 2014

Now, UTIS collects and provides traffic information by building RSE 1,150(unit) and OBE about 51,000(vehicle). it's inevitable to enlarge traffic information sources which use to improve quality of UTIS traffic information for Stabilizing UTIS's service. but there are missing data sections. And, In this study as a way to overcome these problems, based on BIS(Bus information system) installed and operating in the capital area to develop normal vehicle's link transit time estimation model which is used realtime collecting BMS data, we'll utilize the model to provide missing data section's information. For these problem, we selected partial section of suwon-city, anyang-city followed by drive only way or not and conducted model estimating and verification each of BMS data and UTIS traffic information. Consequently, Case2,4,6,8 presented highly credibility between UTIS communication data and estimated value but In the Case 3,5 we determined to replace communication data of UTIS' missing data section too hard for large error. So we need to apply high credibility model formula adjusting road managing condition and the situation of object section.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.61-69
• /
• 2020

This study examined the braking characteristics of a heavy haul freight train with P4a distribution valves applied to domestic high-speed freight trains. A freight train was composed of 50 cars, which is twice the normal operation. A braking test was performed to confirm the characteristics of the braking of a heavy haul. The brake cylinder pressures were measured for emergency and service braking on the 1st, 10th, 20th, 30th, and 50th cars. Because the brake signal is transmitted to the pressure through the braking tube connected to the end of the train, the rear vehicle is braking later than the vehicle ahead. Therefore, it is necessary to predict the brake pressures in all cars in a train to supplement the results of the limited tests and calculate the braking distance. The pressure in each car was determined using empirical models of linear interpolation, stepwise, and exponential models, which provided reliable information. The predictive results of the empirical models were compared with the measured results, and the exponential model was predicted relatively accurately. These results are expected to contribute to the safe operation of heavy haul freight trains and can be used to predict the braking distance and calculate the level of impact between vehicles during braking.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.2
• /
• pp.29-43
• /
• 2019

The calibration of microscopic traffic simulation models has received much attention in the simulation field. Although no standard has been established for it, a genetic algorithm (GA) has been widely employed in recent literature because of its high efficiency to find solutions in such optimization problems. However, the performance still falls short in simulation analyses to support fast decision making. This paper proposes a new calibration procedure using a dual GA and central composite design (CCD) in order to improve the efficiency. The calibration exercise goes through three major sequential steps: (1) experimental design using CCD for a quadratic response surface model (RSM) estimation, (2) 1st GA procedure using the RSM with CCD to find a near-optimal initial population for a next step, and (3) 2nd GA procedure to find a final solution. The proposed method was applied in calibrating the Gipps car-following model with respect to maximizing the likelihood of a spacing distribution between a lead and following vehicle. In order to evaluate the performance of the proposed method, a conventional calibration approach using a single GA was compared under both simulated and real vehicle trajectory data. It was found that the proposed approach enhances the optimization speed by starting to search from an initial population that is closer to the optimum than that of the other approach. This result implies the proposed approach has benefits for a large-scale traffic network simulation analysis. This method can be extended to other optimization tasks using GA in transportation studies.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.4
• /
• pp.423-430
• /
• 2019

The convergence of the automotive industry and the ICT technology can be broadly divided into the commercial service sector and the Cooperative-ITS (C-ITS) service sector. The C-ITS service sector is using V2X communication technology as a field that aims to provide safer transportation, more green and efficient transportation, and more predictable and productive mobility. The recent convergence of self-driving cars and connected cars requires high data rates, low transmission delays, and low transmission error rates. Interest in comparison of performance between WAVE and C-V2X (LTE-V2X, 5G-V2X) has been amplified and application services by communication technology are being studied. In this paper, we design the application performance evaluation method of Hybrid V2X communication system and confirm that the decrease of packet error rate (PER) performance is caused by the increase of communication distance, not the vehicle speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.8
• /
• pp.896-905
• /
• 2012

Recently, the application of the plastic material to automotive components and structures has steadily increased to satisfy demands on the saving of overall weight and the improvement of energy efficiency. The objective of this paper is to investigate the development of a bumper back-beam using a thermoplastic olefin (TPO). The bumper back-beam was designed to be manufactured from the injection molding process. In order to obtain a proper design of the bumper back-beam, three-dimensional finite element analyses were performed for various design alternatives. Stress-strain curves for different strain rates were measured by high speed tensile tests of the TPO to consider strain rate effects in the FEA. The influence of the sectional shape and the rib formation on the contact force-intrusion curves, the deflection and the energy absorption rate of the bumper back-beam was examined. From the results of the examination, a proper design of the bumper back-beam was acquired. The bumper back-beam consisting of TPO was fabricated from the injection moulding process and the vibration welding. Pendulum crash tests were carried out using the fabricated bumper back-beam. The results of the tests showed that the designed bumper back-beam can satisfy requirements of the federal motor vehicle safety standard (FMVSS). Through the comparison of the previously designed bumper back-beam with the newly designed bumper back beam, it was noted that the weight of the designed bumper back-beam is lighter than that of the previously designed bumper back beam by nearly 16 %. In addition, it was considered that the newly designed bumper back beam can improve recycling of the bumper back-beam.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.193-199
• /
• 2016

Since the variations of electromagnetic suspension forces of maglev trains have close relations with the acceleration of the levitated bodies, it is basic to control the levitation forces using the measured acceleration of vehicles. In this study, an airgap control algorithm based on acceleration feedback is applied to maglev trains and a dynamic analysis method is developed considering maglev train-guideway interaction. Using the developed method, dynamic behaviors of a maglev train-guideway interaction system are investigated. It is observed from the analysis that the current design guidelines can be satisfied when the proposed airgap control algorithm is employed. Using the contorl algorithm, the current guidelines can be improved and economical maglev railway guideway structures can be designed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.185-191
• /
• 2006

DSRC((Dedicated Short Range Communication) is dedicated short range communication for wireless communications between RSE(Road Side Equipment) and OBE(On-Board Unit) within vehicle moving high speed. In this paper, we implemented 5.8GHz DSRC modem according to Korea TTA(Telecommunication Technology Association) standard and investigated implementation results and design process for SoC(System on a Chip) embedding ARM CPU which control overall signal and process arithmetic work. The SoC is implemented by 0.11um design technology and 480pins EPBGA package. In the implemented SoC ($Jaguar^{TM}$), 5.8GHz DSRC PHY(Physical Layer) modem and MAC are designed and included. For CPU core ARM926EJ-S is embedded, and LCD controller, smart card controller, ethernet MAC, and memory controller are designed as main function.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.4
• /
• pp.398-404
• /
• 2015

In this paper, we describe the design and performance of a prototype multi-rotor unmaned aerial vehicle( UAV) platform featuring an inertial measurement unit(IMU) based autonomous-flying for use in bluetooth communication environments. Although there has been a fair amount of study of free-flying UAV with multi-rotors, the more recent trend has been to outfit hexarotor helicopter with gimbal to support various services. This paper introduces the hardware and software systems toward very compact and autonomous hexarotors, where they can perform search, rescue, and surveillance missions without external assistance systems like ground station computers, high-performance remote control devices or vision system. The proposed system comprises the construction of the test hexarotor platform, the implementation of an IMU, mathematical modeling and simulation in the helicopter. Furthermore, the hexarotor helicopter with implemented IMU is connected with a micro controller unit(MCU)(ARM-cortex) board. The micro-controller is able to command the rotational speed of the rotors and to get the measurements of the IMU as input signals. The control simulation and experiment on the real system are implemented in the test platform, evaluated and compared against each other.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.2
• /
• pp.99-107
• /
• 2016

Test research on Infra-Red Thermography(IRT) technique in a supersonic wind tunnel has been conducted. Inadvertent technical difficulties and their solutions associated with the technique in running of the facility were examined. Two flow conditions at Mach number of 3 and 4 were considered. A double compression ramp model, that replicates realistic high-speed vehicle configuration, was used as test model. The present IR data were compared with shadowgraph visualization images and laminar computational fluid dynamics(CFD) results. It has been shown that the IRT technique can be used in quantifying various fluid dynamic features such as flow transition, separation and three-dimensional phenomena around the double compression ramp model.