• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1502-1509
• /
• 2006

In this paper, we proposed reliability and capacity enhancement methods for IEEE 802.15.3 HDR-WPAN (High Data Rate-Wireless Personal Area Network) system which is currently getting an interest in home network technology adopting a MIMO technique. We also analyzed performance or the proposed system through a computer simulation. The HDR-WPAN system using V-BLAST algorithm, transmitting the different signal vector to each other's sub-channel, can get the transmission speed of more than 110Mbps using two Tx/Px antenna without bandwidth expansion in TCM-64QAM mode. Also the proposed system has reliability of 104 at $E_b/N_0=35dB$ under the Rayleigh fading channel in case of two Tx/Rx antenna with MMSE algorithm. The HDR-WPAN system adopting V-BLAST method has its drawback which is very complicated to determine the decision-ordering at the receiver. But, the proposed system enhances the transmission capacity and reliability without extra bandwidth expansion by sending data streams to multiple antennas.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.41-46
• /
• 2014

In this paper, a transceiver of VLC (Visible Light Communication) using LED white lighting has been implemented. We analyzed differences between conventional wireless communication and VLC with high-speed data transmission in a variety of environments, and confirmed symbols which passed through a channel using QAM. In order to get a high data rate, we found some variables that should be considered essentially though experiments. In addition, we set a bandwidth and found an optimal gain according to the distance between transmitter and receiver. We analyzed proposed system model through Labview and finally showed a system performance. The performance showed a 2Mbps QAM data rate in real visible light indoor channels.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.9A
• /
• pp.867-875
• /
• 2005

In this paper, we fabricated along distance wireless communication transmitter and receiver over the 100 which used NRD technology. To make the transmitter and receiver of 400Hz band using the non radiative dielectric wave guide, transmitter was composed of gm oscillator, m modulator and antenna, receiver was composed of local gum oscillator, balanced mixer, 3dB direction coupler and antenna. Also we executed a wireless communication image transmission examination to the transmitter and receiver. We receive the image information in real-time data transmission from receiver after we send the image signal in the wireless distance of the 10km. Therefore, the 400Hz band U transmitter and receiver to be developed will be used widely for the transmission system CATV or broadband transmission system. This will be utilized also to the link device of a long distance high speed wireless communication network.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.9
• /
• pp.2022-2028
• /
• 2015

SpaceWire is a standard for high-speed links and networks between spacecraft components, which was invented for better, cheaper and faster on-board data handling in spacecraft. The standard defines timecode and its distribution which can be used for time synchronization among the nodes in a SpaceWire network. A timecode output from the time master which provides standard time over a SpaceWire network travels through links and routers to reach every nodes. While traveling, a timecode suffers from transmission delay and jitter which cause some difference in time synchronization among nodes. In this work, a simulator was developed using OMNeT++ to simulate the operation of a SpaceWire network and some analyses were performed on the transmission delay and jitter accompanied with a transmission of a timecode. The result will be used in the near future for the research of a precise time synchronization technique over a SpaceWire network.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.142-146
• /
• 2012

Today, the demand for high-speed data communication and mobile communication has exploded. Thus, there is a growing need for optical communication systems that convert large volumes of data to optical signals and that accommodate and transmit the signals across long distances. Digital optical communication with these characteristics consists of a master unit (MU) and a slave unit (SU). However, the digital optical units that are currently commercialized or being developed transmit data without compression. Thus, digital optical communication using these units is restricted by the quantity of optical frames when adding diversity or operating with various combinations of CDMA, WCDMA, WiBro, GSM, LTE, and other mobile communication technologies. This paper suggests the application of a data compression algorithm to a digital signal processor (DSP) chip as a field programmable gate array (FPGA) and a complex programmable logic device (CPLD) of a digital optical unit to add separate optical waves or to transmit complex data without specific changes in design of the optical frame.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.2
• /
• pp.26-36
• /
• 2008

Due to the differential and low voltage swing, Low Voltage Differential Signaling(LVDS) has been widely used for high speed data transmission with low power consumption. This paper proposes new LVDS I/O interface circuits for more than 1.3 Gb/s operation. The LVDS receiver proposed in this paper utilizes a sense amp for the pre-amp instead of a conventional differential pre-amp. The proposed LVDS allows more than 1.3 Gb/s transmission speed with significantly reduced driver output voltage. Also, in order to further improve the power consumption and noise performance, this paper introduces an inductance impedance matching technique which can eliminate the termination resistor. A new form of unfolded impedance matching method has been developed to accomplish the impedance matching for LVDS receivers with a sense amplifier as well as with a differential amplifier. The proposed LVDS I/O circuits have been extensively simulated using HSPICE based on 0.35um TSMC CMOS technology. The simulation results show improved power gain and transmission rate by ${\sim}12%$ and ${\sim}18%$, respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.2
• /
• pp.222-231
• /
• 2011

In this paper, we have proposed a method which can make it possible to stably transmit and receive data like the ARC-164 radio frequency hopping environment as a S/W packet modem with PSK modulation. This is a method that the S/W packet modem with PSK digital modulation and the use of PC sound cards change over from data to voice signals and then transmit/receive data. We confirmed not only that it is possible to solve the slow speed communication with the use of sending data through multi-channels and PSK modulation that has the ability to methodically improve transmission rates, but also that it is possible to send the state of frequency hopping stably. In conclusion, we've confirmed both tactical values that though the transmission rate may be a tad slow, a state of frequency hopping of more than 94% confidence plus voice and data can be sent via radio at the same time. In this paper, the proposed S/W packet modem is only an implemented S/W component, so when we apply it to aircraft that we don't consider EMC problems with, then we have the advantage of a wider use of conventional UHF/VHF/HF radio that is possible to voice communication. If we recognize these operational requirements, we can apply for a lot of field equipment efficiently.

• Journal of the Society of Disaster Information
• /
• v.10 no.2
• /
• pp.254-262
• /
• 2014

KISStool is developed and established by KIGAM, in order to link and share the earthquake data easily with institutes related, this study includes the development of a KISStool program format and protocol supporting Kit. The Kit has functions such as transforming and sending a seismic data. The functions of the kit are implemented in modules, which are running on the realtime basis. The firmware is embedded into the Kit, which transforms the seismic data into the formats, miniSEED and QSCD20. These data are sent to KISStool program. We have confirmed the results of the data transforming, transmissions and storage functions are conducted normally, the speed of transmission shows same level when comparing with a standard system. We expect that the firmware developed in this study will have high usability not only for linking with KISStool program through being embedded into incompatible digitizers, but also for improving performance of older ones.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.3
• /
• pp.1-7
• /
• 1975

In this paper, a method of writing and reproducing high density data with ordinary Audio cassette deck is discribed. In writing, the data N or NRZ code are modulated into PM code to take the positive code N(1) and the negative code N(0) are taken from the complement of the NRZ code, each of which are written into 2 channel track. In reading, the error corrected and the clock pulse can be generated from the reading pulse itself. Also, without modifying the interior circuit of the deck it is possible to use the deck in both the data and audio by adapting a few simple circuits. Over the range of 25HZ-4KHZ, it was possible to write and reproduce at the speed of 787 bps transmission rate.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.5
• /
• pp.185-192
• /
• 2011

In this paper, we simulate and analyze performance of iterative coding scheme, double binary turbo code, for high speed power line communication (PLC) systems. PLC system has hostile environment for high speed data transmission, so error correction method is necessary to compensate effects of PLC channel. We employ the PLC model proposed by M. Zimmerman and Middleton Class A interference model, and system performance is evaluated in terms of bit error rate (BER). From the simulation results, we confirm double binary turbo code provides considerable coding gains to PLC system and BER performance is significantly improved as the number of iteration increase. It is also confirmed that BER performance increases as code rate is lager, while it decreases as the code rate is smaller.