• 한국진공학회지
• /
• 제15권2호
• /
• pp.117-138
• /
• 2006

지표면에서 플라즈마는 전기방전에 의하여 만들어낸다. 그래서 대부분의 플라즈마 발생은 1백만분의 1기압보다 더 낮은 기압에서 발생하고 있었다. 그러나 많은 플라즈마 응용은 고기압에서 발생한 플라즈마를 요구하고 있다. 진공펌프와 같은 고가의 장비를 피하기 위하여 과학자들은 1기압이나 그이상의 압력에서 플라즈마를 발생하는 연구를 하기 시작했다. 많은 량의 제료 공정, 환경보호와 개선, 그리고 고효율 에너지 창출과 이용 등의 분야에 플라즈마를 사용할 때에는 오직 더 많은 량의 플라즈마를 더욱 값싸게 만들 때에만 가능한 것이다. 우리는 따라서 고기압에서 플라즈마를 만들어내는 새로운 방법을 개발하고 이러한 플라즈마가 21세기 산업에 적용될 수 있는 새로운 기반을 구축하는 연구를 수행하고 있다. 이러한 기술은 미래의 재료 공정이나, 환경 그리고 에너지 분야에 지대한 영향을 미칠 것으로 생각한다.

• 대한치과의사협회지
• /
• 제54권12호
• /
• pp.1035-1044
• /
• 2016

Purpose : The purpose of this study was to compare the plaque removal effects of vacuum oral cleaner developed for the patients with limited mobility with those of manual toothbrushes and high pressure injection oral cleaner (dental water jet). Meterials and methods : Thirty human subjects were measured with Patient Hygiene Performance index (PHP index) and O'Leary index before and after the use of toothbrush, high pressure injection oral cleaner and vacuum oral cleaner. These three different oral hygiene methods were conducted with seven-day intermittence. Then the statistical analysis was carried out to define plaque removal rate of three different oral hygiene methods (${\alpha}=.05$). Results : According to the efficacy analysis of plaque removal before and after the oral cleaning using each of three methods, significant reduction in plaque after the treatment compared to the previous state when using toothbrush, high pressure injection oral cleaner, and vacuum oral cleaner was observed (P < 0.001). PHP index of tooth brushing was higher than that of the high pressure injection oral cleaner, while PHP index of vacuum oral cleaner did not show significant difference from either of the other two methods. There was no significance difference in O'Leary index among the three methods. Conclusion : Effect of plaque removal using the vacuum oral cleaner is comparable to that of manual tooth brush or high pressure injection oral cleaner, so it will be helpful for self-oral hygiene care of the patients with limited mobility.

• 소성∙가공
• /
• 제21권3호
• /
• pp.195-201
• /
• 2012

A vacuum ladling die casting system is suggested as a means to obtain a high vacuum level. A high vacuum of 17.8 mmHg is obtained by sealing the inner space of the mould. The sample product is a rear-head housing for an auto-compressor, and the die-casting with 6-cavities was conducted. The flow analysis shows that the filling speed during vacuum ladling is faster than for a non-vacuum system. The air holes in the sample product were too small to be seen with the naked eye in X-ray films. Density tests show that the high vacuum ladling system reduces the internal porosity as much as 57.8% when compared to the non-vacuum system. A defective rate of only 0.17% was found from leak testing. The results of this research prove that the high vacuum die-casting process is useful for manufacturing of aluminium components under high internal pressure.

• Journal of Biosystems Engineering
• /
• 제28권6호
• /
• pp.525-530
• /
• 2003

This study was carried out to develop a vacuum nozzle seeder for the automation of large seeds sowing of fruit vegetables and rootstocks. Moreover, the seeding efficiency was examined to find the optimum operating condition considering high precision seeding. The important operating factors for high seeding rate were typically nozzle diameter and absorbing vacuum pressure. The optimum nozzle diameters were found 1.5, 1.5 and 2.0 mm for Chambak, Tuktozwa and Hukjong while the optimum vacuum pressures were 8.0㎪, 10.6㎪ and 5.3㎪, respectively. Under the optimum operating condition, the results indicated that the maximum seeding rates were 97.6％, 98.8％ and 97.6％ respectively for Chambak Tuktozwa and Hukjong. The vibrating acceleration of the hopper did not make any significant effects on the seeding rate when the vacuum pressure reached 8.0㎪ and the sowing rate became higher with lighter seed. As the seed became heavier, the larger diameter of nozzle was recommended 1.5mm of the nozzle diameter was found to be applied for the experimental seeds. The vacuum pressure was also found 8.0㎪ - 13.3㎪ at that time.

• 한국정밀공학회지
• /
• 제30권12호
• /
• pp.1327-1333
• /
• 2013

Air bearings are widely used in precision stages because of low friction and high motion accuracy, however, they suffer from low stiffness in comparison with rolling bearings or hydrostatic bearings. So, several preloading methods using weight, magnet and vacuum force, and opposing pads have been used to increase the stiffness of the air bearings. In this paper, pressure distributions of the vacuum preloaded porous air bearings are calculated using the proposed method. And then, the load capacity and stiffness are analyzed. For the vacuum preloaded air bearings, the stiffness is increased owing to reduced bearing clearance by vacuum force. The simulation results indicate that variation of vacuum pressure with clearance in the vacuum pocket gives rise to low stiffness, so the vacuum pocket should be designed for pressure to be constantly maintained regardless of the bearing clearance by means of large effective pumping speed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.31-34
• /
• 2007

본 연구는 고온의 연소 가스를 이용하여 고공 환경 모사용 초음속 디퓨저의 성능을 파악하는 것이다. 실험 장치는 크게 액체로켓 연소실, 진공 챔버, 냉각수 링 및 디퓨저로 구성되어 있다. 먼저 연소실험 전에 고압의 질소가스(30barg)와 진공 펌프를 이용하여 액체로켓 엔진과 디퓨저의 기밀시험을 수행 하였다. 제작된 디퓨저를 포함한 시험 리그의 기밀테스트 결과， 고압 조건 및 진공압 조건에서 모두 누설이 없이 양호하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.145-152
• /
• 1996

This paper deals with an experimental study on the f~iction torque characteristics of magnctic fluid seals for various oil temperatures, rotating speeds, and vacuum pressures. The friction torque of MFS was measured by high response torque meter. The experimental results show that, as the rotating speed increases, the fi'iction torque of MFS increases and as the oil temperature increases, the friction torque of MFS decreases. Also, the experimental results show that the friction torque of Model II is 1.73 ~ 2.56, 2.0 ~ 2.89, 2.0 - 3.25 times larger than those of Model I under the atmospheric pressure, vacuum pressure(10$^{-4}$ and 10$^{-6}$ torr), respectively.

• Tribology and Lubricants
• /
• 제13권2호
• /
• pp.105-111
• /
• 1997

This paper deals with an experimental study on the friction torque characteristics of magnetic fluid seals for various oil temperatures, rotating speeds, and vacuum pressures. The friction torque of MFS was measured by high response torque meter. The experimental results show that, as the rotating speed increases, the friction torque of MFS increases and as the oil temperature increases, the friction torque of MFS decreases. Also, the experimental results show that the friction torque of Model-II is 1.73~2.56, 2.0~2.89, 2.0~3.25 times higher than those of Model-I under the atmospheric pressure, vacuum pressure ($10^{-4} and 10^{-6}$ torr), respectively.

• 한국수소및신에너지학회논문집
• /
• 제32권6호
• /
• pp.585-591
• /
• 2021

Liquefied hydrogen have advantage which reduces the volume by about 800 times or more compared to hydrogen gas, so it is possible to increase the storage density. However, liquefied hydrogen produced by cryogenic cooling of 20 K or less at normal pressure has a problem of maximizing the insulation effect that blocks heat introduced from the outside. Representative insulation technologies include vacuum insulation and multi-layer insulation materials and in general, heat blocking is attempted by combining insulation technologies. Therefore, in this study, the pressure of the internal vacuum layer was changed to 10^-1, 10^-2, 10^-3 and 10^-4 Torr to confirm the thermal insulation performance of the vacuum jacket valve for transporting liquefied hydrogen. As a result, it was confirmed that the insulation performance improved as the degree of vacuum increased.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권3호
• /
• pp.197-205
• /
• 2004

연약지반 개량을 위해 진공압밀공법을 적용할 경우 발생되는 Hardening Zone의 범위와 진공압 세기의 관계를 연구하였다. 이를 위하여 단위 셀 형식의 시험기를 제작하여 국내의 대표적 준설매립공사지역인 광양, 부산, 목포에서 채취한 고함수비 상태에서의 준설점성토에 대해 각각 함수비와 콘저항치수를 측정하여 진공압의 변화에 따른 Hardening Zone의 변화를 파악하였다. 높은 진공압상태에서는 배수재의 막힘현상과 배수재 부근에서 빠르게 생성되는 Hardening Zone 등으로 인하여 배수층으로의 간극수의 흐름이 방해되어 낮은 진공압상태에서 보다 Hardening zone의 범위가 커지지는 않았다.