• 반도체디스플레이기술학회지
• /
• 제21권1호
• /
• pp.119-126
• /
• 2022

MAS-based glass, which has been studied to replace the ceramic material used in the plasma etching chamber, has problems such as forming and processing due to its high melting temperature. To solve this problem, in this study, fluoride was added to the existing MAS-based glass to increase the workability in the glass manufacturing and to improve the chemical resistance to CF₄/Ar/O₂ plasma gas. Through RAMAN analysis, the structural change of the glass according to the addition of fluoride was observed. In addition, it was confirmed that high-temperature viscosity and thermal properties decreased as the fluoride content increased and plasma resistance was maintained, it showed an excellent etching rate of up to 11 times compared to quartz glass.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.470-475
• /
• 2013

In this study, we report that effects of a filler with a high coefficient of thermal expansion on a sealant for high-temperature ($750{\sim}850^{\circ}C$) SOFC. We designed a $SiO_2-BaO-ZnO-B_2O_3-Al_2O_3$ glass system with a softening temperature higher than $750^{\circ}C$. The properties of the glass system show not only low volumetric shrinking but also low swelling. The glass system did not create a crystal phase during along-term heat treatment. We fabricated a seal gasket with 0, 10, 15, and 20 wt% cristobalite added as filler materials with glass powder. The coefficient of thermal expansion of the seal gasket increased according to cristobalite content. During along-term heat treatment, the leak rate decreased by about 5% after a heat treatment in an oxidizing atmosphere at $750^{\circ}C$ for 2000 h, also decreasing by about 6% after a heat treatment in a reducing atmosphere at $750^{\circ}C$ for 1000 h.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.467-471
• /
• 2018

Diatomite powder, a naturally occurring porous raw material, was used to make ceramic materials with porosity and high strength. The sintering behavior of the diatomite powder at various sintering temperatures suggests that diatomite monoliths with a high porosity and strength can be prepared at $1100^{\circ}C$. The compressive strength of the sintered diatomite monoliths increased as the sintering temperature increased, and the molding pressure of 2 MPa and the binder of 18.6 wt.% were excellent. When the sintering temperature rises, the diatomite powder is melted, and its pores gradually disappear. SEM images show that strengthening begins with the formation of inter-particle bonds at a low sintering temperature.

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.648-653
• /
• 2012

Hybridization of dense ceramic membranes for hydrogen separation with an electronically conductive metallic phase is normally utilized to enhance the hydrogen permeation flux and thereby to increase the production efficiency of hydrogen. In this study, we developed a nickel and proton conducting oxide ($BaCe_{0.9}Y_{0.1}O_{3-{\delta}}$: BCY) based cermet (ceramic-metal composites) membrane. Focused on the general criteria in that the hydrogen permeation properties of a cermet membrane depend on its microstructural features, such as the grain size and the homogeneity of the mix, we tried to optimize the microstructure of Ni-BCY cermets by controlling the fabrication condition. The Ni-BCY composite powder was synthesized via a solid-state reaction using $2NiCO_3{\cdot}3Ni(OH)_2{\cdot}4H_2O$, $BaCeO_3$, $CeO_2$ and $Y_2O_3$ as a starting material. To optimize the mixing scale and homogeneity of the composite powder, we employed a high-energy milling process. With this high-energy milled composite powder, we could fabricate a fine-grained dense membrane with an excellent level of mixing homogeneity. This controlled Ni-BCY cermet membrane showed higher hydrogen permeability compared to uncontrolled Ni-BCY cermets created with a conventionally ball-milled composite powder.

• 한국세라믹학회지
• /
• 제29권3호
• /
• pp.202-210
• /
• 1992

• 한국세라믹학회지
• /
• 제55권4호
• /
• pp.358-363
• /
• 2018

To improve the polarization property of cathodes, which is the main factor limiting the performance of protonic ceramic fuel cells (PCFCs), $K_2NiF_4-type$ $Pr_2NiO_{4+{\delta}}$, which is expected to exhibit a triple conducting property (proton, oxygen ion, and hole conductions) was applied to PCFCs and its properties were investigated. Low-temperature microwave heat-treatment was used to achieve both sufficient interface adhesion between the electrolyte and the cathode layers and suppression of the secondary phase formation due to migration of elements such as barium and cerium. Through this fabrication method, a high performance of $0.82W{\cdot}cm^{-2}$ and low ohmic resistance of $0.06{\Omega}{\cdot}cm^2$ were obtained in an $Ni-BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $Pr_2NiO_{4+{\delta}}$ single cell at $650^{\circ}C$. This result verifies that the $K_2NiF_{4+{\delta}}-type$ cathode shows good chemical compatibility which, in turn, will make it a potent candidate as a PCFC cathode.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.1059-1065
• /
• 1993

The sliding wear behavior of the plasma sprayed zirconia containing 8wt% yttria was investigated over a range of room temperature to 800℃. Both of the friction coefficient and the wear loss increased reaching its maximum at about to 499℃. and then decreased again with increasing temperature up to 800℃. The worn surface at elevated temperature were observed and analyzed by scanning electron microscopy and X-ray diffractometer to study the mechanisms of high temperature wear behavior. Surface morphology of the worn samples changes with temperature. Monoclinic (m)/tetragonal (t) x-ray peak intensity ratio of wear debris and worn surface decreased with increasing temperature. Non-transformable tetragonal (t') to metastable tetragonal (t) phase transformation of worn surface increased with increasing temperature. The results indicate that dehumidification and above phase changes are contributing to the high temperature wear behavior of the plasma sprayed ZrO2-Y2O3 coatings.

• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.199-204
• /
• 1983

An attempt was made to study wetting behavior of various low temperature molten frist on ceramic substrates including high alumina silicon carbide and porous fired clay plates by Sessile-drop method. The cosine values of contact angles between substrates and molten frist were linear as a function of temperature unless chemical reactions between substrate and molten frit occured. Addition of BaO to frit composition indicated that cosine of values of contact angles were gradually increased with increasing temperature but in the frist contained $Li_2O$ consine values were abruptly increased with increasing temperature after reached a certain temperature. The contact angle increased with increasing roughness of the substrate surface in case of alumina substrate plate.

• 한국세라믹학회지
• /
• 제52권4호
• /
• pp.229-233
• /
• 2015

Currently, the majority of commercial white LEDs are phosphor converted LEDs made of a blue-emitting chip and YAG yellow phosphor dispersed in organic silicone. However, silicone in high-power devices results in long-term performance problems such as reacting with water, color transition, and shrinkage by heat. Additionally, yellow phosphor is not applicable to warm white LEDs that require a low CCT and high CRI. To solve these problems, mixing of green phosphor, red phosphor and glass, which are stable in high temperatures, is common a production method for high-power warm white LEDs. In this study, we fabricated conversion lenses with LUAG green phosphor, SCASN red phosphor and low-softening point glass for high-power warm white LEDs. Conversion lenses can be well controlled through the phosphor content and heat treatment temperature. Therefore, when the green phosphor content was increased, the CRI and luminance efficiency gradually intensified. Moreover, using high heat treatment temperatures, the fabricated conversion lenses had a high CRI and low luminance efficiency. Thus, the fabricated conversion lenses with green and red phosphor below 90 wt% and 10 wt% with a sintering temperature of $500^{\circ}C$ had the best optical properties. The measured values for the CCT, CRI and luminance efficiency were 3200 K, 80, and 85 lm/w.

• 한국세라믹학회지
• /
• 제43권9호
• /
• pp.582-587
• /
• 2006

Decomposition behavior of $ferro-Si_3N_4$was investigated with varying temperature and holding time in mud components for high temperature refractory applications. Porosities gradually increased with increasing temperature and holding time due to the carbothermal reduction of $Si_3N_4\;and\;SiO_2$. Silicon monoxide (SiO) as a intermediate resulted from evaporation of $Si_3N_4\;and\;SiO_2$ reacted with C sources to generate needle-like ${\beta}-SiC$ and Fe in $Si_3N_4$ acted as a catalyst in order to enhance growth of SiC grain with the preferred orientation. SiC generation yield increased with increasing holding time, all of the $Si_3N_4\;and\;SiO_2$ affected on SiC formation up to 2h. However, SiC generation was only dependent on residual $SiO_2$ over 2h, because the carbothermal reduction reaction of $Si_3N_4$ was no longer possible at that time.